On 10/17/2016 14:09, Lorenzo Pieralisi wrote: > On Mon, Oct 17, 2016 at 12:36:34AM -0400, Joshua Kinard wrote: >> On 06/23/2016 18:16, Bjorn Helgaas wrote: >>> We claim PCI BAR and bridge window resources in pci_bus_assign_resources(), >>> but when PCI_PROBE_ONLY is set, we treat those resources as immutable and >>> don't call pci_bus_assign_resources(), so the resources aren't put in the >>> resource tree. >>> >>> When the resources aren't in the tree, they don't show up in /proc/iomem, >>> we can't detect conflicts, and we need special cases elsewhere for >>> PCI_PROBE_ONLY or resources without a parent pointer. >>> >>> Claim all PCI BAR and window resources in the PCI_PROBE_ONLY case. >>> >>> If a PCI_PROBE_ONLY platform assigns conflicting resources, Linux can't fix >>> the conflicts. Previously we didn't notice the conflicts, but now we will, >>> which may expose new failures. >>> >>> Signed-off-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx> >>> --- [snip] >> >> So I finally tested this on two SGI platforms, IP30 and IP27. For IP30, it >> works fine once I drop the "pci_set_flags(PCI_PROBE_ONLY);" call. IP30 uses >> standard virtual addressing via ioremap and the like for all of its PCI stuff, >> so it was trivial to fix it. >> >> IP27, on the other hand, is not happy with this change. I don't know about >> mainline IP27, as that's generally bitrotted and didn't boot the last time I >> tried it, but under the refactored code I'm using that actually boots, this >> platform still needs to bypass *all* attempts to claim or assign the PCI addresses. >> >> I suspect the difference with IP27 is unlike normal systems, IP27 uses special >> physical addresses in the 0x92xxxxxxxxxxxxxx block to address I/O devices, so >> there's no proper ioremap or use of virtual addressing for I/O. Ralf, does >> this sound correct? >> >> If I use the patches I got plus this change and set PCI_PROBE_ONLY, this is >> what happens: >> >> [ 47.299511] PCI host bridge to bus 0001:00 >> [ 47.348155] pci_bus 0001:00: root bus resource [mem >> 0x920000000f200000-0x920000000f9fffff] >> [ 47.447663] pci_bus 0001:00: root bus resource [io >> 0x920000000fa00000-0x920000000fbfffff] >> [ 47.547183] pci_bus 0001:00: root bus resource [bus 01-ff] >> [ 47.616581] pci 0001:00:00.0: can't claim BAR 0 [io 0xf200000-0xf2000ff]: >> no compatible bridge window >> [ 47.726766] pci 0001:00:00.0: can't claim BAR 1 [mem 0x0f200000-0x0f200fff]: >> no compatible bridge window >> [ 47.840937] pci 0001:00:00.0: can't claim BAR 6 [mem 0x00000000-0x0000ffff >> pref]: no compatible bridge window >> [ 47.960317] pci 0001:00:01.0: can't claim BAR 0 [io 0xf400000-0xf4000ff]: >> no compatible bridge window >> [ 48.072399] pci 0001:00:01.0: can't claim BAR 1 [mem 0x0f400000-0x0f400fff]: >> no compatible bridge window >> [ 48.186560] pci 0001:00:01.0: can't claim BAR 6 [mem 0x00000000-0x0000ffff >> pref]: no compatible bridge window >> [ 48.305957] pci 0001:00:02.0: can't claim BAR 0 [mem 0x0f600000-0x0f6fffff]: >> no compatible bridge window >> [ 48.420098] pci 0001:00:06.0: can't claim BAR 0 [mem 0x0fa00000-0x0fafffff]: >> no compatible bridge window >> [ 48.534294] pci 0001:00:07.0: can't claim BAR 0 [mem 0x00000000-0x00001fff]: >> no compatible bridge window >> [ 48.648541] qla1280: QLA1040 found on PCI bus 0, dev 0 >> [ 48.710232] PCI: Enabling device 0001:00:00.0 (0006 -> 0007) >> [ 48.779231] qla1280 0001:00:00.0: can't ioremap BAR 1: [mem size 0x00001000] >> [ 48.863145] qla1280: Unable to map I/O memory >> [ 48.916520] qla1280: QLA1040 found on PCI bus 0, dev 1 >> [ 48.977298] PCI: Enabling device 0001:00:01.0 (0006 -> 0007) >> [ 49.046128] qla1280 0001:00:01.0: can't ioremap BAR 1: [mem size 0x00001000] >> [ 49.130201] qla1280: Unable to map I/O memory >> [ 49.183068] IOC3 0001:00:02.0: can't ioremap BAR 0: [mem size 0x00100000] >> [ 49.264292] ioc3: Unable to remap PCI BAR for 0001:00:02.0. >> [ 49.331533] IOC3 0001:00:06.0: can't ioremap BAR 0: [mem size 0x00100000] >> [ 49.412984] ioc3: Unable to remap PCI BAR for 0001:00:06.0. >> >> >> If I disable PCI_PROBE_ONLY, then this: >> >> [ 47.588033] PCI host bridge to bus 0001:00 >> [ 47.636649] pci_bus 0001:00: root bus resource [mem >> 0x920000000f200000-0x920000000f9fffff] >> [ 47.736144] pci_bus 0001:00: root bus resource [io >> 0x920000000fa00000-0x920000000fbfffff] >> [ 47.835621] pci_bus 0001:00: root bus resource [bus 01-ff] >> [ 47.905023] pci 0001:00:02.0: BAR 0: no space for [mem size 0x00100000] >> [ 47.982775] pci 0001:00:02.0: BAR 0: failed to assign [mem size 0x00100000] >> [ 48.066586] pci 0001:00:06.0: BAR 0: no space for [mem size 0x00100000] >> [ 48.146173] pci 0001:00:06.0: BAR 0: failed to assign [mem size 0x00100000] >> [ 48.229972] pci 0001:00:00.0: BAR 6: no space for [mem size 0x00010000 pref] >> [ 48.314783] pci 0001:00:00.0: BAR 6: failed to assign [mem size 0x00010000 pref] >> [ 48.403825] pci 0001:00:01.0: BAR 6: no space for [mem size 0x00010000 pref] >> [ 48.488655] pci 0001:00:01.0: BAR 6: failed to assign [mem size 0x00010000 pref] >> [ 48.577695] pci 0001:00:00.0: BAR 1: no space for [mem size 0x00001000] >> [ 48.657260] pci 0001:00:00.0: BAR 1: failed to assign [mem size 0x00001000] >> [ 48.741068] pci 0001:00:01.0: BAR 1: no space for [mem size 0x00001000] >> [ 48.820644] pci 0001:00:01.0: BAR 1: failed to assign [mem size 0x00001000] >> [ 48.904452] pci 0001:00:00.0: BAR 0: no space for [io size 0x0100] >> [ 48.979840] pci 0001:00:00.0: BAR 0: failed to assign [io size 0x0100] >> [ 49.059459] pci 0001:00:01.0: BAR 0: no space for [io size 0x0100] >> [ 49.134855] pci 0001:00:01.0: BAR 0: failed to assign [io size 0x0100] >> [ 49.214588] qla1280: QLA1040 found on PCI bus 0, dev 0 >> [ 49.277249] qla1280 0001:00:00.0: can't ioremap BAR 1: [??? 0x00000000 flags >> 0x0] >> [ 49.366330] qla1280: Unable to map I/O memory >> [ 49.419832] qla1280: QLA1040 found on PCI bus 0, dev 1 >> [ 49.481211] qla1280 0001:00:01.0: can't ioremap BAR 1: [??? 0x00000000 flags >> 0x0] >> [ 49.570560] qla1280: Unable to map I/O memory >> [ 49.623439] IOC3 0001:00:02.0: can't ioremap BAR 0: [??? 0x00000000 flags 0x0] >> [ 49.709857] ioc3: Unable to remap PCI BAR for 0001:00:02.0. >> [ 49.777113] IOC3 0001:00:06.0: can't ioremap BAR 0: [??? 0x00000000 flags 0x0] >> [ 49.863796] ioc3: Unable to remap PCI BAR for 0001:00:06.0. >> >> >> The only fix I could come up with was more IP27 #ifdef hackery to retain the >> original code for IP27, but use the new conditional logic for all other >> platforms. Would a patch for this be acceptable (with verbose comment), or is >> there a better way to deal with IP27 that doesn't involve re-writing its I/O >> addressing support entirely? > > Would you mind providing a kernel boot log, lspci output and /proc/iomem > /proc/ioports for your "working" system boot ? That would help debugging > what's the expected resources allocation for the system and consequently > where the problem currently lies. Sure. I've disabled line-wrapping on this message so my mail client doesn't mangle the output. First, is the boot output from my serial console: [ 0.000000] Linux version 4.8.2-mipsgit-20161016 (root@helcaraxe) (gcc version 5.4.0 (Gentoo Hardened 5.4.0 p1.0, pie-0.6.5) ) #4 SMP Mon Oct 17 19:48:30 EDT 2016 [ 0.000000] ARCH: SGI-IP27 [ 0.000000] PROMLIB: ARC firmware Version 64 Revision 0 [ 0.000000] SMP: Discovered 4 cpus on 2 nodes [ 0.000000] ************** Topology ******************** [ 0.000000] 00 01 [ 0.000000] 00 255 255 [ 0.000000] 01 255 255 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00000f14 (R14000) [ 0.000000] FPU revision is: 00000900 [ 0.000000] Checking for the multiply/shift bug... no. [ 0.000000] Checking for the daddiu bug... no. [ 0.000000] IP27: Running on node 0. [ 0.000000] IP27: Node 0 has a primary CPU, CPU is running. [ 0.000000] IP27: Node 0 has a secondary CPU, CPU is running. [ 0.000000] IP27: Machine is in M mode. [ 0.000000] IP27: CPU 1A (CPU0): 500 MHz CPU detected. [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0000000000838000 @ 000000000001c000 (usable) [ 0.000000] memory: 000000000057c000 @ 0000000000854000 (usable after init) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] cma: Reserved 32 MiB at 0x00000001fe000000 [ 0.000000] REPLICATION: ON nasid 0, ktext from nasid 0, kdata from nasid 0 [ 0.000000] REPLICATION: ON nasid 1, ktext from nasid 0, kdata from nasid 0 [ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Unified secondary cache 8192kB 2-way, linesize 128 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x00000001ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] node 1: [mem 0x0000000100000000-0x00000001ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] Initmem setup node 1 [mem 0x0000000100000000-0x00000001ffffffff] [ 0.000000] percpu: Embedded 4 pages/cpu @a800000002010000 s36096 r0 d29440 u65536 [ 0.000000] Built 2 zonelists in Node order, mobility grouping on. Total pages: 522240 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=dksc(0,1,0) console=ttyS0,9600 [ 0.000000] PID hash table entries: 4096 (order: 1, 32768 bytes) [ 0.000000] Memory: 8307776K/8388608K available (6498K kernel code, 454K rwdata, 1436K rodata, 5616K init, 543K bss, 48064K reserved, 32768K cma-reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000] NR_IRQS:256 [ 0.000000] clocksource: HUB: mask: 0xfffffffffffff max_cycles: 0x127350b88, max_idle_ns: 1763180808480 ns [ 0.000019] sched_clock: 52 bits at 1250kHz, resolution 800ns, wraps every 4398046510800ns [ 0.102422] Console: colour dummy device 80x25 [ 0.154975] Calibrating delay loop... 749.56 BogoMIPS (lpj=3747840) [ 0.317670] pid_max: default: 32768 minimum: 301 [ 0.377938] Dentry cache hash table entries: 1048576 (order: 9, 8388608 bytes) [ 0.592303] Inode-cache hash table entries: 524288 (order: 8, 4194304 bytes) [ 0.736316] Mount-cache hash table entries: 16384 (order: 3, 131072 bytes) [ 0.817310] Mountpoint-cache hash table entries: 16384 (order: 3, 131072 bytes) [ 0.916094] Checking for the daddi bug... no. [ 0.976495] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 0.976520] Primary data cache 32kB, 2-way, VIPT, no aliases, linesize 32 bytes [ 0.976532] Unified secondary cache 8192kB 2-way, linesize 128 bytes. [ 0.979792] IP27: CPU 1B (CPU1): 500 MHz CPU detected. [ 0.979824] CPU1 revision is: 00000f14 (R14000) [ 0.979831] FPU revision is: 00000900 [ 1.014463] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 1.014493] Primary data cache 32kB, 2-way, VIPT, no aliases, linesize 32 bytes [ 1.014506] Unified secondary cache 8192kB 2-way, linesize 128 bytes. [ 1.017888] IP27: CPU 2A (CPU2): 500 MHz CPU detected. [ 1.017931] CPU2 revision is: 00000f14 (R14000) [ 1.017938] FPU revision is: 00000900 [ 1.055420] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes. [ 1.055452] Primary data cache 32kB, 2-way, VIPT, no aliases, linesize 32 bytes [ 1.055467] Unified secondary cache 8192kB 2-way, linesize 128 bytes. [ 1.058810] IP27: CPU 2B (CPU3): 500 MHz CPU detected. [ 1.058851] CPU3 revision is: 00000f14 (R14000) [ 1.058858] FPU revision is: 00000900 [ 1.092672] Brought up 4 CPUs [ 2.484801] devtmpfs: initialized [ 2.603700] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 2.892716] random: fast init done [ 2.990752] xor: measuring software checksum speed [ 3.146730] 8regs : 486.400 MB/sec [ 3.295350] 8regs_prefetch: 486.400 MB/sec [ 3.448144] 32regs : 486.400 MB/sec [ 3.596768] 32regs_prefetch: 486.400 MB/sec [ 3.650415] xor: using function: 32regs_prefetch (486.400 MB/sec) [ 3.834852] NET: Registered protocol family 16 [ 3.946535] cpuidle: using governor ladder [ 4.043955] cpuidle: using governor menu [ 4.089355] xtalk:n0/0 xbow widget (rev 1.3) [ 4.140796] xtalk:n0/8 kona widget (rev unknown) registered as a platform device. [ 4.230796] xtalk:n0/b bridge widget (rev D) registered as a platform device. [ 4.316712] xtalk:n0/c bridge widget (rev D) registered as a platform device. [ 4.402590] xtalk:n0/d impact widget (rev B) registered as a platform device. [ 4.488444] xtalk:n0/f bridge widget (rev C) registered as a platform device. [ 4.574178] xtalk:n1/0 xbow widget (rev 1.3) [ 5.247396] raid6: int64x1 gen() 84 MB/s [ 5.467370] raid6: int64x1 xor() 80 MB/s [ 5.687324] raid6: int64x2 gen() 151 MB/s [ 5.907243] raid6: int64x2 xor() 116 MB/s [ 6.127125] raid6: int64x4 gen() 235 MB/s [ 6.347155] raid6: int64x4 xor() 142 MB/s [ 6.567117] raid6: int64x8 gen() 251 MB/s [ 6.787018] raid6: int64x8 xor() 175 MB/s [ 6.836420] raid6: using algorithm int64x8 gen() 251 MB/s [ 6.901352] raid6: .... xor() 175 MB/s, rmw enabled [ 6.960002] raid6: using intx1 recovery algorithm [ 7.017544] SCSI subsystem initialized [ 7.063853] clocksource: Switched to clocksource HUB [ 7.363862] FS-Cache: Loaded [ 31.643872] NET: Registered protocol family 2 [ 31.696149] TCP established hash table entries: 65536 (order: 5, 524288 bytes) [ 31.787294] TCP bind hash table entries: 65536 (order: 6, 1048576 bytes) [ 31.874832] TCP: Hash tables configured (established 65536 bind 65536) [ 31.952084] UDP hash table entries: 4096 (order: 3, 131072 bytes) [ 32.026304] UDP-Lite hash table entries: 4096 (order: 3, 131072 bytes) [ 32.403836] NET: Registered protocol family 1 [ 32.583876] RPC: Registered named UNIX socket transport module. [ 32.653282] RPC: Registered udp transport module. [ 32.709785] RPC: Registered tcp transport module. [ 32.766346] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 34.045622] futex hash table entries: 1024 (order: 3, 131072 bytes) [ 34.275238] workingset: timestamp_bits=40 max_order=19 bucket_order=0 [ 34.350961] zbud: loaded [ 37.383916] NFS: Registering the id_resolver key type [ 37.442917] Key type id_resolver registered [ 37.493101] Key type id_legacy registered [ 37.541388] efs: 1.0a - http://aeschi.ch.eu.org/efs/ [ 37.873853] SGI XFS with ACLs, security attributes, realtime, no debug enabled [ 39.453936] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 39.541066] io scheduler noop registered [ 39.588223] io scheduler deadline registered [ 39.639639] io scheduler cfq registered (default) [ 39.973936] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 40.148640] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 40.245916] loop: module loaded [ 40.283288] mousedev: PS/2 mouse device common for all mice [ 40.349460] md: linear personality registered for level -1 [ 40.414802] md: raid0 personality registered for level 0 [ 40.478677] md: raid1 personality registered for level 1 [ 40.542549] md: raid10 personality registered for level 10 [ 40.609068] md: raid6 personality registered for level 6 [ 40.672411] md: raid5 personality registered for level 5 [ 40.736315] md: raid4 personality registered for level 4 [ 40.800808] PCI host bridge to bus 0000:00 [ 40.849424] pci_bus 0000:00: root bus resource [mem 0x920000000b200000-0x920000000b9fffff] [ 40.948920] pci_bus 0000:00: root bus resource [io 0x920000000ba00000-0x920000000bbfffff] [ 41.048408] pci_bus 0000:00: root bus resource [bus 00-ff] [ 41.114880] PCI host bridge to bus 0001:00 [ 41.163629] pci_bus 0001:00: root bus resource [mem 0x920000000c200000-0x920000000c9fffff] [ 41.263152] pci_bus 0001:00: root bus resource [io 0x920000000ca00000-0x920000000cbfffff] [ 41.362645] pci_bus 0001:00: root bus resource [bus 01-ff] [ 41.430847] PCI host bridge to bus 0002:00 [ 41.478263] pci_bus 0002:00: root bus resource [mem 0x920000000f200000-0x920000000f9fffff] [ 41.577771] pci_bus 0002:00: root bus resource [io 0x920000000fa00000-0x920000000fbfffff] [ 41.677250] pci_bus 0002:00: root bus resource [bus 02-ff] [ 41.746742] qla1280: QLA1040 found on PCI bus 0, dev 0 [ 41.806687] PCI: Enabling device 0002:00:00.0 (0006 -> 0007) [ 41.875796] scsi(0): Enabling vchannel on BRIDGE for SGI/MIPS [ 42.324520] random: crng init done [ 42.839160] scsi(0:0): Resetting SCSI BUS [ 45.964232] scsi host0: QLogic QLA1040 PCI to SCSI Host Adapter [ 45.964232] Firmware version: 7.65.06, Driver version 3.27.1 [ 46.118149] qla1280: QLA1040 found on PCI bus 0, dev 1 [ 46.178192] PCI: Enabling device 0002:00:01.0 (0006 -> 0007) [ 46.289985] scsi 0:0:1:0: Direct-Access SEAGATE SX150176LC BA12 PQ: 0 ANSI: 2 [ 46.387174] scsi(0:0:1:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 31 [ 46.486875] scsi 0:0:2:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 46.583893] scsi(0:0:2:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 31 [ 46.683736] scsi 0:0:3:0: Direct-Access SEAGATE SX150176LC BA08 PQ: 0 ANSI: 2 [ 46.780696] scsi(0:0:3:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 31 [ 46.880821] scsi 0:0:4:0: Direct-Access SEAGATE SX150176LC BA11 PQ: 0 ANSI: 2 [ 46.977716] scsi(0:0:4:0): Sync: period 10, offset 12, Wide, Tagged queuing: depth 31 [ 47.077797] scsi 0:0:5:0: Direct-Access SEAGATE SX150176LC BA11 PQ: 0 ANSI: 2 [ 47.174768] scsi(0:0:5:0):[ 47.181219] scsi(1:0): Resetting SCSI BUS [ 47.251839] Sync: period 10, offset 12, Wide, Tagged queuing: depth 31 [ 47.639912] scsi 0:0:6:0: CD-ROM TOSHIBA CD-ROM XM-5701TA 0167 PQ: 0 ANSI: 2 [ 47.736890] scsi(0:0:6:0): Sync: period 10, offset 12 [ 51.553976] scsi host1: QLogic QLA1040 PCI to SCSI Host Adapter [ 51.553976] Firmware version: 7.65.06, Driver version 3.27.1 [ 51.998859] ioc3: part: [], serial: [] => class IP27 BaseIO [ 52.068783] ioc3-eth: Ethernet address is 08:00:69:05:64:74. [ 52.136831] IOC3 0002:00:02.0 eth0: link up, 100Mbps, full-duplex, lpa 0x8DE1 [ 52.220897] eth0: Using PHY 31, vendor 0x20005c0, model 0, rev 0. [ 52.294232] eth0: IOC3 SSRAM has 128 kbyte. [ 52.345852] rtc-m48t35 rtc-m48t35: rtc core: registered m48t35 as rtc0 [ 52.588471] console [ttyS0] enabled [ 52.489601] 0002:00:02.0: ttyS0 at IOC3 0xf620178 (irq = 0, base_baud = 458333) is a 16550A [ 52.671141] bootconsole [early0] disabled [ 54.146680] 0002:00:02.0: ttyS1 at IOC3 0xf620170 (irq = 0, base_baud = 458333) is a 16550A [ 54.248408] IOC3 Master Driver loaded for 0002:00:02.0 [ 54.313895] ioc3: NIC search failed. [ 54.356992] ioc3: part: [], serial: [] => class IP27 BaseIO [ 54.424356] ioc3: request_irq fails for IRQ 0xffffffff [ 54.490948] ioc3-eth: Ethernet address is 00:00:00:00:00:00. [ 54.561038] IOC3 0002:00:06.0 eth1: link down [ 54.613597] eth1: Using PHY 31, vendor 0x0, model 0, rev 0. [ 54.680825] eth1: IOC3 SSRAM has 64 kbyte. [ 54.765266] 0002:00:06.0: ttyS2 at IOC3 0xfa20178 (irq = 0, base_baud = 458333) is a 16550A [ 54.888655] 0002:00:06.0: ttyS3 at IOC3 0xfa20170 (irq = 0, base_baud = 458333) is a 16550A [ 54.990198] IOC3 Master Driver loaded for 0002:00:06.0 [ 55.052840] NET: Registered protocol family 26 [ 55.509832] sd 0:0:1:0: [sda] 97693755 512-byte logical blocks: (50.0 GB/46.6 GiB) [ 55.515697] sr 0:0:6:0: [sr0] scsi-1 drive [ 55.515709] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 55.520834] sd 0:0:4:0: [sdd] 97693755 512-byte logical blocks: (50.0 GB/46.6 GiB) [ 55.523611] sd 0:0:4:0: [sdd] Write Protect is off [ 55.526511] sd 0:0:4:0: [sdd] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 55.550956] sdd: sdd1 sdd2 sdd3 sdd4 sdd5 sdd6 sdd9 sdd11 [ 55.562326] sd 0:0:4:0: [sdd] Attached SCSI disk [ 55.564803] sd 0:0:5:0: [sde] 97693755 512-byte logical blocks: (50.0 GB/46.6 GiB) [ 55.567564] sd 0:0:5:0: [sde] Write Protect is off [ 55.570463] sd 0:0:5:0: [sde] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 55.600908] sd 0:0:5:0: [sde] Attached SCSI disk [ 55.604715] sd 0:0:2:0: [sdb] 97693755 512-byte logical blocks: (50.0 GB/46.6 GiB) [ 55.605297] sd 0:0:3:0: [sdc] 97693755 512-byte logical blocks: (50.0 GB/46.6 GiB) [ 55.607054] sd 0:0:2:0: [sdb] Write Protect is off [ 55.607592] sd 0:0:3:0: [sdc] Write Protect is off [ 55.609959] sd 0:0:2:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 55.610460] sd 0:0:3:0: [sdc] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 55.631199] sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb9 sdb11 [ 55.634048] sdc: sdc1 sdc2 sdc3 sdc4 sdc5 sdc6 sdc9 sdc11 [ 55.646437] sd 0:0:3:0: [sdc] Attached SCSI disk [ 55.647162] sd 0:0:2:0: [sdb] Attached SCSI disk [ 57.150140] sd 0:0:1:0: [sda] Write Protect is off [ 57.173988] NET: Registered protocol family 10 [ 57.264566] sd 0:0:1:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 57.386960] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda9 sda11 [ 57.464000] sd 0:0:1:0: [sda] Attached SCSI disk [ 57.544064] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 57.617430] NET: Registered protocol family 17 [ 57.671360] 8021q: 802.1Q VLAN Support v1.8 [ 57.722075] sctp: Hash tables configured (bind 1024/1024) [ 58.093962] Key type dns_resolver registered [ 58.148015] rtc-m48t35 rtc-m48t35: setting system clock to 2016-10-17 23:49:58 UTC (1476748198) [ 59.626451] Freeing unused kernel memory: 5616K (a800000000854000 - a800000000dd0000) [ 59.720950] This architecture does not have kernel memory protection. Next is /proc/iomem and /proc/ioports: # cat /proc/iomem 0f600000-0f6fffff : ioc3 0f680000-0f687fff : rtc-m48t35 0fa00000-0fafffff : ioc3 920000000b200000-920000000b9fffff : Bridge MEM 920000000c200000-920000000c9fffff : Bridge MEM 920000000f200000-920000000f9fffff : Bridge MEM / # cat /proc/ioports 920000000ba00000-920000000bbfffff : Bridge IO 920000000ca00000-920000000cbfffff : Bridge IO 920000000fa00000-920000000fbfffff : Bridge IO And lspci -vvvx: / # /usr/sbin/lspci -vvvx 0001:00:00.0 Unassigned class [ff00]: Silicon Graphics Intl. Corp. Linc I/O controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 Region 0: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=134217729] Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Expansion ROM at <unassigned> [disabled] [size=2] lspci: Unable to load libkmod resources: error -12 00: a9 10 02 00 00 00 00 02 00 00 00 ff 00 f8 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0001:00:01.0 Unassigned class [ff00]: Silicon Graphics Intl. Corp. Linc I/O controller Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 Region 0: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=134217729] Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Expansion ROM at <unassigned> [disabled] [size=2] 00: a9 10 02 00 00 00 00 02 00 00 00 ff 00 f8 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0002:00:00.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev 05) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 1 NUMA node: 0 Region 0: I/O ports at f200000 [size=257] Region 1: Memory at 0f200000 (32-bit, non-prefetchable) [size=4097] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Expansion ROM at <unassigned> [disabled] [size=65537] Kernel driver in use: qla1280 00: 77 10 20 10 07 00 00 02 05 00 00 01 40 40 00 00 10: 01 00 20 0f 00 00 20 0f 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0002:00:01.0 SCSI storage controller: QLogic Corp. ISP1020 Fast-wide SCSI (rev 05) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 256 bytes Interrupt: pin A routed to IRQ 2 NUMA node: 0 Region 0: I/O ports at f400000 [size=257] Region 1: Memory at 0f400000 (32-bit, non-prefetchable) [size=4097] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Expansion ROM at <unassigned> [disabled] [size=65537] Kernel driver in use: qla1280 00: 77 10 20 10 07 00 00 02 05 00 00 01 40 40 00 00 10: 01 00 40 0f 00 00 40 0f 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0002:00:02.0 Unassigned class [ff00]: Silicon Graphics Intl. Corp. IOC3 I/O controller (rev 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 3 NUMA node: 0 Region 0: Memory at 0f600000 (32-bit, non-prefetchable) [size=1048577] Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Expansion ROM at <unassigned> [disabled] [size=2] Kernel driver in use: IOC3 00: a9 10 03 00 06 00 80 02 01 00 00 ff 00 40 00 00 10: 00 00 60 0f 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0002:00:06.0 Unassigned class [ff00]: Silicon Graphics Intl. Corp. IOC3 I/O controller (rev 01) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 5 NUMA node: 0 Region 0: Memory at 0fa00000 (32-bit, non-prefetchable) [size=1048577] Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [size=2] Expansion ROM at <unassigned> [disabled] [size=2] Kernel driver in use: IOC3 00: a9 10 03 00 06 00 80 02 01 00 00 ff 00 40 00 00 10: 00 00 a0 0f 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00 0002:00:07.0 Non-VGA unclassified device: Silicon Graphics Intl. Corp. RAD Audio (rev 70) Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- NUMA node: 0 Region 0: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=8193] Region 1: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 2: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 3: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 4: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Region 5: Memory at <unassigned> (32-bit, non-prefetchable) [disabled] [size=2] Expansion ROM at <unassigned> [disabled] [size=2] 00: a9 10 05 00 00 00 80 04 70 00 00 00 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 IP27 hardware does some interesting things with address spaces, depending on which "mode" you run the machine in. "M mode" is the only one that's really usable these days (the other, "N mode", doesn't boot). Under M mode, there's five address spaces, of which, "I/O Space" is selectable by turning on specific bits in the 64-bit memory address. So, given 0x920000000b200000, bits 63:62 select physical addressing (10) and bits 58:57 select I/O space (01), resulting in all PCI addresses (or any I/O address) appearing in the 0x92xxxxxxxxxxxxxx range. The rest of the bits go on to select which NUMA node the I/O is targeted at and which Crosstalk widget to access, and so on. I still haven't fully understood it all myself just yet. You can google for document 007-3410-001, "Origin and Onyx2 Programmer's Reference Manual" for more details (it's no longer available via SGI's TechPubs, but it is archived on plenty of other sites). This particular machine that I have has three "BRIDGE" chips in it, all attached to the Crosstalk bus. Each BRIDGE can address up to 8 PCI devices, but some crosstalk boards slap a BRIDGE chip on for just a single device. In this instance, the BRIDGE w/ address 0x920000000fxxxxxx is the IO6 at xtalk widget 0xf (this has the basic I/O devices for this machine). The BRIDGE at 0x920000000cxxxxxx (widget 0xc) is a PCI "shoebox" that can hold up to three PCI-X cards, and the BRIDGE at 0x920000000bxxxxxx (widget 0xb) is an SGI-specific HIPPI board (ID'ed as a LINC I/O controller by pci.ids). -- Joshua Kinard Gentoo/MIPS kumba@xxxxxxxxxx 6144R/F5C6C943 2015-04-27 177C 1972 1FB8 F254 BAD0 3E72 5C63 F4E3 F5C6 C943 "The past tempts us, the present confuses us, the future frightens us. And our lives slip away, moment by moment, lost in that vast, terrible in-between." --Emperor Turhan, Centauri Republic -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
