Hi Arnd > -----Original Message----- > From: Arnd Bergmann [mailto:arnd@xxxxxxxx] > Sent: 14 September 2016 22:32 > To: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > Cc: Yuanzhichang; devicetree@xxxxxxxxxxxxxxx; > lorenzo.pieralisi@xxxxxxx; Gabriele Paoloni; minyard@xxxxxxx; > gregkh@xxxxxxxxxxxxxxxxxxx; benh@xxxxxxxxxxxxxxxxxxx; John Garry; > will.deacon@xxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; xuwei (O); Linuxarm; > linux-serial@xxxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx; > zourongrong@xxxxxxxxx; liviu.dudau@xxxxxxx; kantyzc@xxxxxxx; > zhichang.yuan02@xxxxxxxxx > Subject: Re: [PATCH V3 2/4] ARM64 LPC: LPC driver implementation on > Hip06 > > On Wednesday, September 14, 2016 10:50:44 PM CEST zhichang.yuan wrote: > > > > On 2016/9/14 20:33, Arnd Bergmann wrote: > > > On Wednesday, September 14, 2016 8:15:52 PM CEST Zhichang Yuan > wrote: > > > > > >> +Required properties: > > >> +- compatible: should be "hisilicon,low-pin-count" > > >> +- #address-cells: must be 2 which stick to the ISA/EISA binding > doc. > > >> +- #size-cells: must be 1 which stick to the ISA/EISA binding doc. > > >> +- reg: base address and length of the register set for the > device. > > >> +- ranges: define a 1:1 mapping between the I/O space of the child > device and > > >> + the parent. > > > > > > Do we still need the "ranges" here? The property in your example > seems > > > wrong. > > > > I think "ranges" is needed. > > without this, of_translate_address --> __of_translate_address --> > of_translate_one will fail when translating the child's IO resource. > > > > > > > >> + ranges = <0x01 0xe4 0x0 0xe4 0x1000>; > > > > > > You translate I/O port 0x00e4 through 0x10e4 to CPU address 0x0e4? > > The hip06 LPC is defined as isa type. > > So, 0x01 0xe4 is the local IO address of 0xe4. With this ranges, 0xe4 > of child will be 1:1 mapped as 0xe4. > > It means no translation. > > No, "no translation" would be leaving out the ranges, we should > fix the code so it handles this case according to the specification > of the ISA DT binding, rather than adding an incorrect ranges > property to make it work with the incorrect Linux implementation. > > of_translate_address() should fail here, and whichever code calls > it should try something else, possibly something we have to > implement that can return the correct IORESOURCE_* type. >From <<3.1.1. Open Firmware Properties for Bus Nodes>> in http://www.firmware.org/1275/bindings/isa/isa0_4d.ps I quote: "There shall be an entry in the "ranges" property for each of the Memory and/or I/O spaces if that address space is mapped through the bridge." It seems to me that it is ok to have 1:1 address mapping and that therefore of_translate_address() should fail if "ranges" is not present. This is also explained quite well in http://lxr.free-electrons.com/source/drivers/of/address.c#L490 what do you think? Thanks Gab > > > > > > > I don't get this part. The bus driver should not care what its > > > children are, just register and PIO ranges that the bus can handle > > > in theory, i.e. from 0x000 to 0xfff. > > > > Just as we discussed in V2, the legacy PIO range is specific to some > > device, such as for ipmi bt, 0xe4 - 0xe7 will be populated. > > I don't want to occupy a larger PIO range in which only small part > PIOs > > are used by our LPC. At this moment, two PIO ranges are using > > through the device property configuration, 0xe4-0xe7, 0x2f8-0x2ff. > > > > If we configure 0-0x1000 for the LPC to cover those two ranges, most > > PIO are wasted and other PIO device on other buses lose the chance to > > use the PIO below 0x1000. > > Otherwise, PIO conflict will happen. So, My idea is only occupied > > the PIO ranges which are really needed for the children. > > The only thing it can realistically conflict with would be another > LPC bus behind on a PCI host bridge. On ARM64, all regular PCI > devices that have IORESOURCE_IO ports are intentionally moved > to (bus) port numbers above 0x1000. > > > And there are probably multiple child devices under LPC, the global > arm64_extio_ops only can cover one PIO range. It is fortunate only ipmi > driver can not support I/O > > operation registering, serial driver has serial_in/serial_out to > > be registered. So, only the PIO range for ipmi device is stored > > in arm64_extio_ops and the indirect-IO > > works well for ipmi device. > > You should not do that in the serial driver, please just use the > normal 8250 driver that works fine once you handle the entire > port range. > > > Arnd -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
