This patch adds a binding that describes the Rockchip PCIe controller
found on Rockchip SoCs PCIe interface.
Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
Reviewed-by: Brian Norris <briannorris@xxxxxxxxxxxx>
---
Changes in v9: None
Changes in v8:
- add Brian's review-tag
Changes in v7:
- move optional properties ahead of interrupt subnode
- use 0-base index for INTx
Changes in v6:
- add ack tag from Rob
Changes in v5:
- fix wrong example reported by Marc
- add seperate section to describe the interrupt controller child
node
Changes in v4:
- fix example of adding intermediate interrupt controller for pcie
legacy interrrupt
Changes in v3:
- fix example dts code suggested by Rob and Marc
- remove driver's behaviour of regulator
Changes in v2:
- fix lots clk/reset stuff suggested by Heiko
- remove msi-parent and add msi-map suggested by Marc
- drop phy related stuff
- some others minor fixes
.../devicetree/bindings/pci/rockchip-pcie.txt | 106 +++++++++++++++++++++
1 file changed, 106 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt
diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
new file mode 100644
index 0000000..3f74c87
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
@@ -0,0 +1,106 @@
+* Rockchip AXI PCIe Root Port Bridge DT description
+
+Required properties:
+- #address-cells: Address representation for root ports, set to <3>
+- #size-cells: Size representation for root ports, set to <2>
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- compatible: Should contain "rockchip,rk3399-pcie"
+- reg: Two register ranges as listed in the reg-names property
+- reg-names: Must include the following names
+ - "axi-base"
+ - "apb-base"
+- clocks: Must contain an entry for each entry in clock-names.
+ See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+ - "aclk"
+ - "aclk-perf"
+ - "hclk"
+ - "pm"
+- msi-map: Maps a Requester ID to an MSI controller and associated.
+ See ./pci-msi.txt
+- phys: From PHY bindings: Phandle for the Generic PHY for PCIe.
+- phy-names: MUST be "pcie-phy".
+- interrupts: Three interrupt entries must be specified.
+- interrupt-names: Must include the following names
+ - "sys"
+ - "legacy"
+ - "client"
+- resets: Must contain five entries for each entry in reset-names.
+ See ../reset/reset.txt for details.
+- reset-names: Must include the following names
+ - "core"
+ - "mgmt"
+ - "mgmt-sticky"
+ - "pipe"
+- pinctrl-names : The pin control state names
+- pinctrl-0: The "default" pinctrl state
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+- interrupt-map-mask and interrupt-map: standard PCI properties
+
+Optional Property:
+- ep-gpios: contain the entry for pre-reset gpio
+- num-lanes: number of lanes to use
+- vpcie3v3-supply: The phandle to the 3.3v regulator to use for pcie.
+- vpcie1v8-supply: The phandle to the 1.8v regulator to use for pcie.
+- vpcie0v9-supply: The phandle to the 0.9v regulator to use for pcie.
+
+*Interrupt controller child node*
+The core controller provides a single interrupt for legacy INTx. The pcie node
+should contain an interrupt controller node as a target for the PCI
+'interrupt-map' property. This node represents the domain at which the four
+INTx interrupts are decoded and routed.
+
+
+Required properties for Interrupt controller child node:
+- interrupt-controller: identifies the node as an interrupt controller
+- #address-cells: specifies the number of cells needed to encode an
+ address. The value must be 0.
+- #interrupt-cells: specifies the number of cells needed to encode an
+ interrupt source. The value must be 1.
+
+Example:
+
+pcie0: pcie@f8000000 {
+ compatible = "rockchip,rk3399-pcie";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
+ <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>;
+ clock-names = "aclk", "aclk-perf",
+ "hclk", "pm";
+ bus-range = <0x0 0x1>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>;
+ interrupt-names = "sys", "legacy", "client";
+ assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
+ assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
+ assigned-clock-rates = <100000000>;
+ ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000
+ 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>;
+ num-lanes = <4>;
+ msi-map = <0x0 &its 0x0 0x1000>;
+ reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>;
+ reg-names = "axi-base", "apb-base";
+ resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
+ <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
+ reset-names = "core", "mgmt", "mgmt-sticky", "pipe";
+ phys = <&pcie_phy>;
+ phy-names = "pcie-phy";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreq>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+ <0 0 0 2 &pcie0_intc 1>,
+ <0 0 0 3 &pcie0_intc 2>,
+ <0 0 0 4 &pcie0_intc 3>;
+ pcie0_intc: interrupt-controller {
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+};
--
2.3.7
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
