> On 13/07/16 10:36, Bharat Kumar Gogada wrote: > >> Subject: Re: PCIe MSI address is not written at pci_enable_msi_range > >> call > >> > >> On 13/07/16 10:10, Bharat Kumar Gogada wrote: > >>>> Subject: Re: PCIe MSI address is not written at > >>>> pci_enable_msi_range call > >>>> > >>>> On 13/07/16 09:33, Bharat Kumar Gogada wrote: > >>>>>> Subject: Re: PCIe MSI address is not written at > >>>>>> pci_enable_msi_range call > >>>>>> > >>>>>> On 13/07/16 07:22, Bharat Kumar Gogada wrote: > >>>>>>>> Subject: Re: PCIe MSI address is not written at > >>>>>>>> pci_enable_msi_range call > >>>>>>>> > >>>>>>>> On 11/07/16 10:33, Bharat Kumar Gogada wrote: > >>>>>>>>> Hi Marc, > >>>>>>>>> > >>>>>>>>> Thanks for the reply. > >>>>>>>>> > >>>>>>>>> From PCIe Spec: > >>>>>>>>> MSI Enable Bit: > >>>>>>>>> If 1 and the MSI-X Enable bit in the MSI-X Message Control > >>>>>>>>> register (see Section 6.8.2.3) is 0, the function is permitted > >>>>>>>>> to use MSI to request service and is prohibited from using its > >>>>>>>>> INTx# > >> pin. > >>>>>>>>> > >>>>>>>>> From Endpoint perspective, MSI Enable = 1 indicates MSI can be > >>>>>>>>> used > >>>>>>>> which means MSI address and data fields are > available/programmed. > >>>>>>>>> > >>>>>>>>> In our SoC whenever MSI Enable goes from 0 --> 1 the hardware > >>>>>>>>> latches > >>>>>>>> onto MSI address and MSI data values. > >>>>>>>>> > >>>>>>>>> With current MSI implementation in kernel, our SoC is latching > >>>>>>>>> on to incorrect address and data values, as address/data are > >>>>>>>>> updated much later > >>>>>>>> than MSI Enable bit. > >>>>>>>> > >>>>>>>> As a side question, how does setting the affinity work on this > >>>>>>>> end-point if this involves changing the address programmed in > >>>>>>>> the MSI > >>>>>> registers? > >>>>>>>> Do you expect the enabled bit to be toggled to around the write? > >>>>>>>> > >>>>>>> > >>>>>>> Yes, > >>>>>> > >>>>>> Well, that's pretty annoying, as this will not work either. But > >>>>>> maybe your > >>>> MSI > >>>>>> controller has a single doorbell? You haven't mentioned which HW > >>>>>> that > >>>> is... > >>>>>> > >>>>> The MSI address/data is located in config space, in our SoC for > >>>>> the logic > >>>> behind PCIe > >>>>> to become aware of new address/data MSI enable transition is used > >>>>> (0 to > >>>> 1). > >>>>> The logic cannot keep polling these registers in configuration > >>>>> space as it > >>>> would consume power. > >>>>> > >>>>> So the logic uses the transition in MSI enable to latch on to > address/data. > >>>> > >>>> I understand the "why". I'm just wondering if your SoC needs to > >>>> have the MSI address changed when changing the affinity of the MSI? > >>>> What MSI controller are you using? Is it in mainline? > >>>> > >>> Can you please give more information on MSI affinity ? > >>> For cpu affinity for interrupts we would use MSI-X. > >>> > >>> We are using GIC 400 v2. > >> > >> None of that is relevant. GIC400 doesn't have the faintest notion of > >> what an MSI is, and MSI-X vs MSI is an end-point property. > >> > >> Please answer these questions: does your MSI controller have a unique > >> doorbell, or multiple doorbells? Does it use wired interrupts (SPIs) > >> connected to the GIC? Is the support code for this MSI controller in > mainline or not? > >> > > > > It has single doorbell. > > The MSI decoding is part of our PCIe bridge, and it has SPI to GIC. > > Our root driver is in mainline drivers/pci/host/pcie-xilinx-nwl.c > > OK, so you're not affected by this affinity setting issue. Please let me know if > the patch I sent yesterday improve things for you once you have a chance to > test it. > Hi Marc, I tested with the patch you provided, now it is working for us. Can you please point to any doc related to affinity in MSI, until now we came across affinity for MSI-X. I will explore more on it. Thanks for your help. Regards, Bharat This email and any attachments are intended for the sole use of the named recipient(s) and contain(s) confidential information that may be proprietary, privileged or copyrighted under applicable law. If you are not the intended recipient, do not read, copy, or forward this email message or any attachments. Delete this email message and any attachments immediately. -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
