Re: Re: [Qemu-devel] [RFC PATCH 0/3] x86: Add support for guest DMA dirty page tracking

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Alex,

On 2016/1/6 0:18, Alexander Duyck wrote:
On Tue, Jan 5, 2016 at 1:40 AM, Michael S. Tsirkin <mst@xxxxxxxxxx> wrote:
On Mon, Jan 04, 2016 at 07:11:25PM -0800, Alexander Duyck wrote:
The two mechanisms referenced above would likely require coordination with
QEMU and as such are open to discussion.  I haven't attempted to address
them as I am not sure there is a consensus as of yet.  My personal
preference would be to add a vendor-specific configuration block to the
emulated pci-bridge interfaces created by QEMU that would allow us to
essentially extend shpc to support guest live migration with pass-through
devices.

shpc?

That is kind of what I was thinking.  We basically need some mechanism
to allow for the host to ask the device to quiesce.  It has been
proposed to possibly even look at something like an ACPI interface
since I know ACPI is used by QEMU to manage hot-plug in the standard
case.

- Alex


Start by using hot-unplug for this!

Really use your patch guest side, and write host side
to allow starting migration with the device, but
defer completing it.

Yeah, I'm fully on board with this idea, though I'm not really working
on this right now since last I knew the folks on this thread from
Intel were working on it.  My patches were mostly meant to be a nudge
in this direction so that we could get away from the driver specific
code.

I have seen your email about live migration.

I conclude the idea you proposed as following.
1. Extend swiotlb to allow for a page dirtying functionality.
2. Use pci express capability to implement of a PCI bridge to act
   as a bridge between direct assigned devices and the host bridge.
3. Using APCI event or extend shpc driver to support device pause.
Is it right?

Will you implement the patchs for live migration?

Sincerely,
Zhou Jie



So

1.- host tells guest to start tracking memory writes
2.- guest acks
3.- migration starts
4.- most memory is migrated
5.- host tells guest to eject device
6.- guest acks
7.- stop vm and migrate rest of state


Sounds about right.  The only way this differs from what I see as the
final solution for this is that instead of fully ejecting the device
in step 5 the driver would instead pause the device and give the host
something like 10 seconds to stop the VM and resume with the same
device connected if it is available.  We would probably also need to
look at a solution that would force the device to be ejected or abort
prior to starting the migration if it doesn't give us the ack in step
2.

It will already be a win since hot unplug after migration starts and
most memory has been migrated is better than hot unplug before migration
starts.

Right.  Generally the longer the VF can be maintained as a part of the
guest the longer the network performance is improved versus using a
purely virtual interface.

Then measure downtime and profile. Then we can look at ways
to quiesce device faster which really means step 5 is replaced
with "host tells guest to quiesce device and dirty (or just unmap!)
all memory mapped for write by device".

Step 5 will be the spot where we really need to start modifying
drivers.  Specifically we probably need to go through and clean-up
things so that we can reduce as many of the delays in the driver
suspend/resume path as possible.  I suspect there is quite a bit that
can be done there that would probably also improve boot and shutdown
times since those are also impacted by the devices.

- Alex



.



--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux