On 31/05/16 10:48, Shawn Lin wrote:
> Hi Marc,
>
> 在 2016/5/30 19:08, Marc Zyngier 写道:
>> On Fri, 20 May 2016 18:29:06 +0800
>> Shawn Lin <shawn.lin@xxxxxxxxxxxxxx> wrote:
>>
>>> This patch add some required and optional properties for Rockchip
>>> PCIe controller. Also we add a example for how to use it.
>>>
>>> Signed-off-by: Shawn Lin <shawn.lin@xxxxxxxxxxxxxx>
>>>
>>> ---
>>>
>>> .../devicetree/bindings/pci/rockchip-pcie.txt | 93 ++++++++++++++++++++++
>>> 1 file changed, 93 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>>> new file mode 100644
>>> index 0000000..69a0804
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie.txt
>>> @@ -0,0 +1,93 @@
>>> +* Rockchip AXI PCIe Root Port Bridge DT description
>>> +
>>> +Required properties:
>>> +- #address-cells: Address representation for root ports, set to <3>
>>> +- #size-cells: Size representation for root ports, set to <2>
>>> +- #interrupt-cells: specifies the number of cells needed to encode an
>>> + interrupt source. The value must be 1.
>>> +- compatible: Should contain "rockchip,rk3399-pcie"
>>> +- reg: Two register ranges as listed in the reg-names property
>>> +- reg-names: The first entry must be "axi-base" for the core registers
>>> + The second entry must be "apb-base" for the client pcie registers
>>> +- clocks: Must contain an entry for each entry in clock-names.
>>> + See ../clocks/clock-bindings.txt for details.
>>> +- clock-names: Must include the following entries:
>>> + - "aclk_pcie"
>>> + - "aclk_perf_pcie"
>>> + - "hclk_pcie"
>>> + - "clk_pciephy_ref"
>>> +- interrupts: Three interrupt entries must be specified.
>>> +- interrupt-names: Must include the following names
>>> + - "pcie-sys"
>>> + - "pcie-legacy"
>>> + - "pcie-client"
>>> +- resets: Must contain five entries for each entry in reset-names.
>>> + See ../reset/reset.txt for details.
>>> +- reset-names: Must include the following names
>>> + - "phy-rst"
>>> + - "core-rst"
>>> + - "mgmt-rst"
>>> + - "mgmt-sticky-rst"
>>> + - "pipe-rst"
>>> +- rockchip,grf: phandle to the syscon managing the "general register files"
>>> +- pcie-conf: offset of pcie client block for configuration
>>> +- pcie-status: offset of pcie client block for status
>>> +- pcie-laneoff: offset of pcie client block for lane
>>> +- msi-parent: Link to the hardware entity that serves as the Message
>>> +- pinctrl-names : The pin control state names
>>> +- pinctrl-0: The "default" pinctrl state
>>> +- interrupt-map-mask and interrupt-map: standard PCI properties
>>> +- interrupt-controller: identifies the node as an interrupt controller
>>> +
>>> +Optional Property:
>>> +- ep-gpios: contain the entry for pre-reset gpio
>>> +- num-lanes: number of lanes to use
>>> +- assigned-clocks, assigned-clock-parents and assigned-clock-rates: standard
>>> + clock bindings. See ../clock/clock-bindings.txt
>>> +
>>> +Example:
>>> +
>>> +pci_express: axi-pcie@f8000000 {
>>> + #address-cells = <3>;
>>> + #size-cells = <2>;
>>> + compatible = "rockchip,rk3399-pcie";
>>> + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>,
>>> + <&cru PCLK_PCIE>, <&cru SCLK_PCIEPHY_REF>;
>>> + clock-names = "aclk_pcie", "aclk_perf_pcie",
>>> + "hclk_pcie", "clk_pciephy_ref";
>>> + bus-range = <0x0 0x1>;
>>> + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
>>> + interrupt-names: "pcie-sys", "pcie-legacy", "pcie-client";
>>> + assigned-clocks = <&cru SCLK_PCIEPHY_REF>;
>>> + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>;
>>> + assigned-clock-rates = <100000000>;
>>> + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
>>> + ranges = < 0x82000000 0 0xfa000000 0x0 0xfa000000 0 0x600000
>>> + 0x81000000 0 0xfa600000 0x0 0xfa600000 0 0x100000 >;
>>> + num-lanes = <4>;
>>> + reg = < 0x0 0xf8000000 0x0 0x2000000 >, < 0x0 0xfd000000 0x0 0x1000000 >;
>>> + reg-name = "axi-base", "apb-base";
>>> + resets = <&cru SRST_PCIEPHY>, <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
>>> + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>;
>>> + reset-names = "phy-rst", "core-rst", "mgmt-rst", "mgmt-sticky-rst", "pipe-rst";
>>> + rockchip,grf = <&grf>;
>>> + pcie-conf = <0xe220>;
>>> + pcie-status = <0xe2a4>;
>>> + pcie-laneoff = <0xe214>;
>>> + pinctrl-names = "default";
>>> + pinctrl-0 = <&pcie_clkreq>;
>>> + msi-parent = <&its>;
>>
>> We've moved away from bare msi-parent for the ITS (notice that the
>> binding mandates #msi-cells = <1>). So what you need here is an msi-map
>> (as described in Documentation/devicetree/bindings/pci/pci-msi.txt).
>>
>> Do you have an IOMMU (or some other remapping HW) between the RC and the
>> GIC ITS? If so, yo may have to describe the mappings between the PCIe
>> RID and the ITS DevID in this msi-map.
>>
>
> yes, we don't need msi-parent here. And we don't need msi-map as well,
> since we don't have a IOMMU block between RC and ITS which need to be
> described in msi-map.
Well, if have neither msi-parent nor msi-map, you won't get MSI at all.
Maybe that's good enough for you, but in that case, make sure you drop
all the MSI code from your patches! ;-) More seriously, you do need an
msi-map, even if that's with a single entry.
Thanks,
M.
--
Jazz is not dead. It just smells funny...
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
