On Mon, 9 May 2016 17:38:27 -0400 Murali Karicheri <m-karicheri2@xxxxxx> wrote: > On 05/09/2016 05:23 PM, Alex Williamson wrote: > > On Mon, 9 May 2016 17:02:23 -0400 > > Murali Karicheri <m-karicheri2@xxxxxx> wrote: > > > >> Hi Bjorn, > >> > >> Thanks for your quick response! > >> See below for some follow up question. > >> > >> On 05/09/2016 04:34 PM, Bjorn Helgaas wrote: > >>> Hi Murali, > >>> > >>> On Mon, May 09, 2016 at 03:32:42PM -0400, Murali Karicheri wrote: > >>>> Bjorn, > >>>> > >>>> I am running into an issue with using a rtk8168 GiB NIC card with Keystone PCIe. > >>>> It works for 32bit BARs such as the Marvel SATA controller on K2E. On another > >>>> recent SoC (K2G) that re-uses the same driver and hardware, I have issues > >>>> bringing up PCIe. > >>>> > >>>> The rtk8168 NIC gets detected, but all read values are zeros. Based on the boot > >>>> log, it appears to be getting assigned 64bit BARs. See the log on K2E with Marvell > >>>> controller and that on K2G with rtk8168. Is there way we can get it assigned > >>>> 32Bit BAR and get it functional? Keystone is a 32bit ARM A15 SoC. > >>>> > >>>> Here are the logs. > >>>> > >>>> K2E log with Marvel controller (Good working case). > >>>> =================================================== > >>>> [ 0.236353] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] > >>>> [ 0.236364] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] > >>>> [ 0.236373] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] > >>>> [ 0.236385] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] > >>>> [ 0.236394] pci 0000:01:00.0: BAR 5: assigned [mem 0x60000000-0x600001ff] > >>>> [ 0.236406] pci 0000:01:00.0: BAR 4: assigned [io 0x1000-0x100f] > >>>> [ 0.236418] pci 0000:01:00.0: BAR 0: assigned [io 0x1010-0x1017] > >>>> [ 0.236429] pci 0000:01:00.0: BAR 2: assigned [io 0x1018-0x101f] > >>>> [ 0.236441] pci 0000:01:00.0: BAR 1: assigned [io 0x1020-0x1023] > >>>> [ 0.236452] pci 0000:01:00.0: BAR 3: assigned [io 0x1024-0x1027] > >>>> [ 0.236464] pci 0000:00:00.0: PCI bridge to [bus 01] > >>>> [ 0.236472] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] > >>>> [ 0.236481] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] > >>>> [ 0.236490] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] > >>>> > >>>> K2G log with Tealtek NIC card > >>>> ============================= > >>>> [ 2.311572] keystone-pcie 21801000.pcie: PCI host bridge to bus 0000:00 > >>>> [ 2.318188] pci_bus 0000:00: root bus resource [bus 00-ff] > >>>> [ 2.323844] pci_bus 0000:00: root bus resource [io 0x0000-0x3fff] > >>>> [ 2.330023] pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff] > >>> > >>> There's no "(bus address ...)" annotation here, which means these > >>> windows map CPU addresses to identical bus addresses. The > >>> "[mem 0x50000000-0x5fffffff]" window is a 32-bit window. > >>> > >>>> [ 2.337567] PCI: bus0: Fast back to back transfers disabled > >>>> [ 2.361159] PCI: bus1: Fast back to back transfers disabled > >>>> [ 2.366889] pci 0000:00:00.0: BAR 8: assigned [mem 0x50000000-0x500fffff] > >>>> [ 2.373841] pci 0000:00:00.0: BAR 9: assigned [mem 0x50100000-0x501fffff pref] > >>>> [ 2.381061] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] > >>>> [ 2.387225] pci 0000:01:00.0: BAR 6: assigned [mem 0x50100000-0x5011ffff pref] > >>>> [ 2.394505] pci 0000:01:00.0: BAR 4: assigned [mem 0x50120000-0x5012ffff 64bit pref] > >>>> [ 2.402288] pci 0000:01:00.0: BAR 2: assigned [mem 0x50000000-0x50000fff 64bit] > >>> > >>> I assume these BARs (2 and 4) are the ones in question. They are > >>> 64-bit BARs, but the addresses currently assigned to them fit in 32 > >>> bits, so the space is already all below 4GB. > >>> > >>> The BAR type (32-bit or 64-bit) is built into the device; Linux > >>> doesn't have any influence on that. The type is encoded in the > >>> low-order four bits of the BAR, which are read-only. > >>> > >>>> [ 2.409610] pci 0000:01:00.0: BAR 0: assigned [io 0x1000-0x10ff] > >>>> [ 2.415729] pci 0000:00:00.0: PCI bridge to [bus 01] > >>>> [ 2.420693] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] > >>>> [ 2.426806] pci 0000:00:00.0: bridge window [mem 0x50000000-0x500fffff] > >>>> [ 2.433610] pci 0000:00:00.0: bridge window [mem 0x50100000-0x501fffff pref] > >>>> [ 2.441365] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt > >>>> [ 2.448323] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt > >>>> [ 2.455567] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded > >>>> [ 2.461332] r8169 0000:01:00.0: enabling device (0140 -> 0143) > >>>> [ 2.468789] r8169 0000:01:00.0 eth0: RTL8169 at 0xf0d6a000, 00:00:00:00:00:00, XID 00000000 IRQ 286 > >>> > >>> Looks like this is printed by rtl_init_one(). I see that we read > >>> zeroes from MAC0 and TxConfig, but I don't see any PCI problem here. > >> So if device specific configuration registers for this device are mapped > >> to the window to have 64bit access, they are to be accessed with proper > >> address to get the lower 32 bits of the data, right? So is there a chance > >> it is making access to upper 4 bytes and hence reading all zeros? > >> > >>> Could it be that some EEPROM on the card hasn't been programmed yet? > >>> Does the card work if you put it in a different machine? > >>> > >> Probably. I will ask this to the owner of r8169 driver. He seems to think > >> the access is not right. I need to find a PC that has PCIe slot to do this > >> test. Meanwhile do you know of any 1GiB NIC card that has 32bit BARs and > >> driver in Linux? > > > > I happen to have an Intel 82571EB (PRO/1000 PT Dual Port Server > > Adapter) that only has 32bit BARs: > > > > 02:00.0 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit Ethernet Controller [8086:105e] (rev 06) > > Region 0: Memory at fe7e0000 (32-bit, non-prefetchable) [size=128K] > > Region 1: Memory at fe7c0000 (32-bit, non-prefetchable) [size=128K] > > Region 2: I/O ports at e800 [size=32] > > 02:00.1 Ethernet controller [0200]: Intel Corporation 82571EB Gigabit Ethernet Controller [8086:105e] (rev 06) > > Region 0: Memory at fe7a0000 (32-bit, non-prefetchable) [size=128K] > > Region 1: Memory at fe780000 (32-bit, non-prefetchable) [size=128K] > > Region 2: I/O ports at e400 [size=32] > Alex, > > Thanks for the response. I see following mini pci card which match with your > description. > > http://www.amazon.com/Intel-1000-Dual-Server-Adapter/dp/B000BMZHX2/ref=sr_1_1?ie=UTF8&qid=1462829688&sr=8-1&keywords=intel+expi9402pt > > Is this same thing? I assume e1000e/82571.c is the driver for this. > Could you please confirm so that I can procure the same? I would venture to say yes, but I offer no guarantees ;) Ark seems to indicate all 1000 PT dual port cards use that chip: http://ark.intel.com/products/50494/Intel-PRO1000-PT-Dual-Port-Server-Adapter -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
