Signed-off-by: Yoshinori Sato <ysato@xxxxxxxxxxxxxxxxxxxx>
---
.../devicetree/bindings/pci/sh7751-pci.txt | 51 ++++
drivers/pci/host/Kconfig | 7 +
drivers/pci/host/Makefile | 1 +
drivers/pci/host/pci-sh7751.c | 321 +++++++++++++++++++++
drivers/pci/host/pci-sh7751.h | 269 +++++++++++++++++
5 files changed, 649 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pci/sh7751-pci.txt
create mode 100644 drivers/pci/host/pci-sh7751.c
create mode 100644 drivers/pci/host/pci-sh7751.h
diff --git a/Documentation/devicetree/bindings/pci/sh7751-pci.txt b/Documentation/devicetree/bindings/pci/sh7751-pci.txt
new file mode 100644
index 0000000..45b5152
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/sh7751-pci.txt
@@ -0,0 +1,51 @@
+* Renesas SH7751 PCI host interfaces
+
+Required properties:
+ - compatible: "renesas,sh7751-pci" is required.
+ And board specific compatible if fixup required.
+
+ - reg: base address and length of the pcie controller registers.
+ - #address-cells: set to <2>
+ - #size-cells: set to <1>
+ - bus-range: PCI bus numbers covered
+ - device_type: set to "pci"
+ - ranges: ranges for the PCI memory and I/O regions.
+ - interrupt-map-mask and interrupt-map: standard PCI properties
+ to define the mapping of the PCIe interface to interrupt
+ numbers.
+
+Example:
+ pci: pci-controller@fe200000 {
+ compatible = "renesas,sh7751-pci", "iodata,landisk";
+ device_type = "pci";
+ bus-range = <0 0>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ ranges = <0x02000000 0x00000000 0xfd000000 0xfd000000 0x00000000 0x01000000>,
+ <0x01000000 0x00000000 0xfe240000 0x00000000 0x00000000 0x00040000>;
+ reg = <0xfe200000 0x0400>,
+ <0x0c000000 0x04000000>,
+ <0xff800000 0x0030>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0x1800 0 7>;
+ interrupt-map = <0x0000 0 1 &cpldintc evt2irq(0x2a0) 0
+ 0x0000 0 2 &cpldintc evt2irq(0x2c0) 0
+ 0x0000 0 3 &cpldintc evt2irq(0x2e0) 0
+ 0x0000 0 4 &cpldintc evt2irq(0x300) 0
+
+ 0x0800 0 1 &cpldintc evt2irq(0x2c0) 0
+ 0x0800 0 2 &cpldintc evt2irq(0x2e0) 0
+ 0x0800 0 3 &cpldintc evt2irq(0x300) 0
+ 0x0800 0 4 &cpldintc evt2irq(0x2a0) 0
+
+ 0x1000 0 1 &cpldintc evt2irq(0x2e0) 0
+ 0x1000 0 2 &cpldintc evt2irq(0x300) 0
+ 0x1000 0 3 &cpldintc evt2irq(0x2a0) 0
+ 0x1000 0 4 &cpldintc evt2irq(0x2c0) 0
+
+ 0x1800 0 1 &cpldintc evt2irq(0x300) 0
+ 0x1800 0 2 &cpldintc evt2irq(0x2a0) 0
+ 0x1800 0 3 &cpldintc evt2irq(0x2c0) 0
+ 0x1800 0 4 &cpldintc evt2irq(0x2e0) 0>;
+ };
+};
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 7a0780d..a8596db 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -231,4 +231,11 @@ config PCI_HOST_THUNDER_ECAM
help
Say Y here if you want ECAM support for CN88XX-Pass-1.x Cavium Thunder SoCs.
+config PCI_SH7751
+ bool "Renesas SH7751 On-Chip PCI controller"
+ depends on OF && SUPERH
+ select PCI_HOST_COMMON
+ help
+ Say Y here if you want PCI support on SH7751.
+
endmenu
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index d85b5fa..91268cb 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -28,3 +28,4 @@ obj-$(CONFIG_PCI_HISI) += pcie-hisi.o
obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
obj-$(CONFIG_PCI_HOST_THUNDER_ECAM) += pci-thunder-ecam.o
obj-$(CONFIG_PCI_HOST_THUNDER_PEM) += pci-thunder-pem.o
+obj-$(CONFIG_PCI_SH7751) += pci-sh7751.o
diff --git a/drivers/pci/host/pci-sh7751.c b/drivers/pci/host/pci-sh7751.c
new file mode 100644
index 0000000..fd6548b
--- /dev/null
+++ b/drivers/pci/host/pci-sh7751.c
@@ -0,0 +1,321 @@
+/*
+ * SH7751 PCI driver
+ * Copyright (C) 2016 Yoshinori Sato
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_pci.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include "pci-host-common.h"
+#include "pci-sh7751.h"
+
+#define pcic_writel(val, reg) __raw_writel(val, pci_reg_base + (reg))
+#define pcic_readl(reg) __raw_readl(pci_reg_base + (reg))
+
+unsigned long PCIBIOS_MIN_IO;
+unsigned long PCIBIOS_MIN_MEM;
+DEFINE_RAW_SPINLOCK(pci_config_lock);
+
+/*
+ * PCIC fixups
+ */
+
+static __initconst const struct fixups {
+ char *compatible;
+ void (*fixup)(void __iomem *, void __iomem *);
+} fixup_list[] = {
+};
+
+static __init void pcic_fixups(struct device_node *np,
+ void __iomem *pcic, void __iomem *bcr)
+{
+ int i;
+ const struct fixups *f = fixup_list;
+
+ for (i = 0; i < ARRAY_SIZE(fixup_list); i++) {
+ if (of_device_is_compatible(np, f->compatible)) {
+ f->fixup(pcic, bcr);
+ break;
+ }
+ }
+}
+
+/*
+ * Direct access to PCI hardware...
+ */
+#define CONFIG_CMD(bus, devfn, where) \
+ (0x80000000 | (bus->number << 16) | (devfn << 8) | (where & ~3))
+
+/*
+ * Functions for accessing PCI configuration space with type 1 accesses
+ */
+static int sh4_pci_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *val)
+{
+ struct gen_pci *pci = bus->sysdata;
+ void __iomem *pci_reg_base = (void __iomem *)pci->cfg.res.start;
+ unsigned long flags;
+ u32 data;
+
+ /*
+ * PCIPDR may only be accessed as 32 bit words,
+ * so we must do byte alignment by hand
+ */
+ raw_spin_lock_irqsave(&pci_config_lock, flags);
+ pcic_writel(CONFIG_CMD(bus, devfn, where), SH4_PCIPAR);
+ data = pcic_readl(SH4_PCIPDR);
+ raw_spin_unlock_irqrestore(&pci_config_lock, flags);
+
+ switch (size) {
+ case 1:
+ *val = (data >> ((where & 3) << 3)) & 0xff;
+ break;
+ case 2:
+ *val = (data >> ((where & 2) << 3)) & 0xffff;
+ break;
+ case 4:
+ *val = data;
+ break;
+ default:
+ return PCIBIOS_FUNC_NOT_SUPPORTED;
+ }
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+/*
+ * Since SH4 only does 32bit access we'll have to do a read,
+ * mask,write operation.
+ * We'll allow an odd byte offset, though it should be illegal.
+ */
+static int sh4_pci_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 val)
+{
+ struct gen_pci *pci = bus->sysdata;
+ void __iomem *pci_reg_base = (void __iomem *)pci->cfg.res.start;
+ unsigned long flags;
+ int shift;
+ u32 data;
+
+ raw_spin_lock_irqsave(&pci_config_lock, flags);
+ pcic_writel(CONFIG_CMD(bus, devfn, where), SH4_PCIPAR);
+ data = pcic_readl(SH4_PCIPDR);
+ raw_spin_unlock_irqrestore(&pci_config_lock, flags);
+
+ switch (size) {
+ case 1:
+ shift = (where & 3) << 3;
+ data &= ~(0xff << shift);
+ data |= ((val & 0xff) << shift);
+ break;
+ case 2:
+ shift = (where & 2) << 3;
+ data &= ~(0xffff << shift);
+ data |= ((val & 0xffff) << shift);
+ break;
+ case 4:
+ data = val;
+ break;
+ default:
+ return PCIBIOS_FUNC_NOT_SUPPORTED;
+ }
+
+ pcic_writel(data, SH4_PCIPDR);
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static struct gen_pci_cfg_bus_ops pci_sh7751_ops = {
+ .ops = {
+ .read = sh4_pci_read,
+ .write = sh4_pci_write,
+ },
+};
+
+/*
+ * Called after each bus is probed, but before its children
+ * are examined.
+ */
+void pcibios_fixup_bus(struct pci_bus *bus)
+{
+}
+
+/*
+ * We need to avoid collisions with `mirrored' VGA ports
+ * and other strange ISA hardware, so we always want the
+ * addresses to be allocated in the 0x000-0x0ff region
+ * modulo 0x400.
+ */
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+ resource_size_t size, resource_size_t align)
+{
+ resource_size_t start = res->start;
+
+ return start;
+}
+
+int pci_mmap_page_range(struct pci_dev *dev, struct vm_area_struct *vma,
+ enum pci_mmap_state mmap_state, int write_combine)
+{
+ /*
+ * I/O space can be accessed via normal processor loads and stores on
+ * this platform but for now we elect not to do this and portable
+ * drivers should not do this anyway.
+ */
+ if (mmap_state == pci_mmap_io)
+ return -EINVAL;
+
+ /*
+ * Ignore write-combine; for now only return uncached mappings.
+ */
+ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+
+ return remap_pfn_range(vma, vma->vm_start, vma->vm_pgoff,
+ vma->vm_end - vma->vm_start,
+ vma->vm_page_prot);
+}
+
+static const struct of_device_id sh7751_pci_of_match[] = {
+ { .compatible = "renesas,sh7751-pci", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, sh7751_pci_of_match);
+
+static int __init area_sdram_check(void __iomem *pci_reg_base,
+ void __iomem *bcr,
+ unsigned int area)
+{
+ unsigned long word;
+
+ word = __raw_readl(bcr + SH7751_BCR1);
+ /* check BCR for SDRAM in area */
+ if (((word >> area) & 1) == 0) {
+ printk("PCI: Area %d is not configured for SDRAM. BCR1=0x%lx\n",
+ area, word);
+ return 0;
+ }
+ pcic_writel(word, SH4_PCIBCR1);
+
+ word = __raw_readw(bcr + SH7751_BCR2);
+ /* check BCR2 for 32bit SDRAM interface*/
+ if (((word >> (area << 1)) & 0x3) != 0x3) {
+ printk("PCI: Area %d is not 32 bit SDRAM. BCR2=0x%lx\n",
+ area, word);
+ return 0;
+ }
+ pcic_writel(word, SH4_PCIBCR2);
+
+ return 1;
+}
+
+static __init int sh7751_pci_probe(struct platform_device *pdev)
+{
+ struct resource *res, *wres;
+ u32 id;
+ u32 reg, word;
+ void __iomem *pci_reg_base;
+ void __iomem *bcr;
+ struct gen_pci *pci;
+
+ pci = devm_kzalloc(&pdev->dev, sizeof(*pci), GFP_KERNEL);
+ if (!pci)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pci_reg_base = (void __iomem *)res->start;
+ if (IS_ERR(pci_reg_base))
+ return PTR_ERR(pci_reg_base);
+
+ wres = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (IS_ERR(wres))
+ return PTR_ERR(wres);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ bcr = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(pci_reg_base))
+ return PTR_ERR(bcr);
+
+ /* check for SH7751/SH7751R hardware */
+ id = pcic_readl(SH7751_PCICONF0);
+ if (id != ((SH7751_DEVICE_ID << 16) | SH7751_VENDOR_ID) &&
+ id != ((SH7751R_DEVICE_ID << 16) | SH7751_VENDOR_ID)) {
+ pr_warn("PCI: This is not an SH7751(R)\n");
+ return -ENODEV;
+ }
+ dev_info(&pdev->dev, "PCI core found at %p\n",
+ pci_reg_base);
+
+ /* Set the BCR's to enable PCI access */
+ reg = __raw_readl(bcr);
+ reg |= 0x80000;
+ __raw_writel(reg, bcr);
+
+ /* Turn the clocks back on (not done in reset)*/
+ pcic_writel(0, SH4_PCICLKR);
+ /* Clear Powerdown IRQ's (not done in reset) */
+ word = SH4_PCIPINT_D3 | SH4_PCIPINT_D0;
+ pcic_writel(word, SH4_PCIPINT);
+
+ /* set the command/status bits to:
+ * Wait Cycle Control + Parity Enable + Bus Master +
+ * Mem space enable
+ */
+ word = SH7751_PCICONF1_WCC | SH7751_PCICONF1_PER |
+ SH7751_PCICONF1_BUM | SH7751_PCICONF1_MES;
+ pcic_writel(word, SH7751_PCICONF1);
+
+ /* define this host as the host bridge */
+ word = PCI_BASE_CLASS_BRIDGE << 24;
+ pcic_writel(word, SH7751_PCICONF2);
+
+ /* Set IO and Mem windows to local address
+ * Make PCI and local address the same for easy 1 to 1 mapping
+ */
+ word = wres->end - wres->start - 1;
+ pcic_writel(word, SH4_PCILSR0);
+ /* Set the values on window 0 PCI config registers */
+ word = P2SEGADDR(wres->start);
+ pcic_writel(word, SH4_PCILAR0);
+ pcic_writel(word, SH7751_PCICONF5);
+
+ /* check BCR for SDRAM in specified area */
+ area_sdram_check(pci_reg_base, bcr, (wres->start >> 27) & 0x07);
+
+ /* configure the wait control registers */
+ word = __raw_readl(bcr + SH7751_WCR1);
+ pcic_writel(word, SH4_PCIWCR1);
+ word = __raw_readl(bcr + SH7751_WCR2);
+ pcic_writel(word, SH4_PCIWCR2);
+ word = __raw_readl(bcr + SH7751_WCR3);
+ pcic_writel(word, SH4_PCIWCR3);
+ word = __raw_readl(bcr + SH7751_MCR);
+ pcic_writel(word, SH4_PCIMCR);
+
+ pcic_fixups(pdev->dev.of_node, pci_reg_base, bcr);
+
+ /* SH7751 init done, set central function init complete */
+ /* use round robin mode to stop a device starving/overruning */
+ word = SH4_PCICR_PREFIX | SH4_PCICR_CFIN | SH4_PCICR_ARBM;
+ pcic_writel(word, SH4_PCICR);
+
+ pci->cfg.ops = &pci_sh7751_ops;
+ return pci_host_common_probe(pdev, pci);
+}
+
+static __refdata struct platform_driver sh7751_pci_driver = {
+ .driver = {
+ .name = "sh7751-pci",
+ .of_match_table = sh7751_pci_of_match,
+ },
+ .probe = sh7751_pci_probe,
+};
+module_platform_driver(sh7751_pci_driver);
+
+MODULE_DESCRIPTION("SH7751 PCI driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pci/host/pci-sh7751.h b/drivers/pci/host/pci-sh7751.h
new file mode 100644
index 0000000..4f8230e
--- /dev/null
+++ b/drivers/pci/host/pci-sh7751.h
@@ -0,0 +1,269 @@
+/*
+ * Low-Level PCI Support for SH7751 targets
+ *
+ * Dustin McIntire (dustin@xxxxxxxxxxxx) (c) 2001
+ * Paul Mundt (lethal@xxxxxxxxxxxx) (c) 2003
+ *
+ * May be copied or modified under the terms of the GNU General Public
+ * License. See linux/COPYING for more information.
+ *
+ */
+
+#ifndef _PCI_SH7751_H_
+#define _PCI_SH7751_H_
+
+#define SH4_PCICR 0x100 /* PCI Control Register */
+ #define SH4_PCICR_PREFIX 0xA5000000 /* CR prefix for write */
+ #define SH4_PCICR_FTO 0x00000400 /* TRDY/IRDY Enable */
+ #define SH4_PCICR_TRSB 0x00000200 /* Target Read Single */
+ #define SH4_PCICR_BSWP 0x00000100 /* Target Byte Swap */
+ #define SH4_PCICR_PLUP 0x00000080 /* Enable PCI Pullup */
+ #define SH4_PCICR_ARBM 0x00000040 /* PCI Arbitration Mode */
+ #define SH4_PCICR_MD 0x00000030 /* MD9 and MD10 status */
+ #define SH4_PCICR_SERR 0x00000008 /* SERR output assert */
+ #define SH4_PCICR_INTA 0x00000004 /* INTA output assert */
+ #define SH4_PCICR_PRST 0x00000002 /* PCI Reset Assert */
+ #define SH4_PCICR_CFIN 0x00000001 /* Central Fun. Init Done */
+#define SH4_PCILSR0 0x104 /* PCI Local Space Register0 */
+#define SH4_PCILSR1 0x108 /* PCI Local Space Register1 */
+#define SH4_PCILAR0 0x10C /* PCI Local Addr Register1 */
+#define SH4_PCILAR1 0x110 /* PCI Local Addr Register1 */
+#define SH4_PCIINT 0x114 /* PCI Interrupt Register */
+ #define SH4_PCIINT_MLCK 0x00008000 /* Master Lock Error */
+ #define SH4_PCIINT_TABT 0x00004000 /* Target Abort Error */
+ #define SH4_PCIINT_TRET 0x00000200 /* Target Retry Error */
+ #define SH4_PCIINT_MFDE 0x00000100 /* Master Func. Disable Error */
+ #define SH4_PCIINT_PRTY 0x00000080 /* Address Parity Error */
+ #define SH4_PCIINT_SERR 0x00000040 /* SERR Detection Error */
+ #define SH4_PCIINT_TWDP 0x00000020 /* Tgt. Write Parity Error */
+ #define SH4_PCIINT_TRDP 0x00000010 /* Tgt. Read Parity Err Det. */
+ #define SH4_PCIINT_MTABT 0x00000008 /* Master-Tgt. Abort Error */
+ #define SH4_PCIINT_MMABT 0x00000004 /* Master-Master Abort Error */
+ #define SH4_PCIINT_MWPD 0x00000002 /* Master Write PERR Detect */
+ #define SH4_PCIINT_MRPD 0x00000001 /* Master Read PERR Detect */
+#define SH4_PCIINTM 0x118 /* PCI Interrupt Mask */
+ #define SH4_PCIINTM_TTADIM BIT(14) /* Target-target abort interrupt */
+ #define SH4_PCIINTM_TMTOIM BIT(9) /* Target retry timeout */
+ #define SH4_PCIINTM_MDEIM BIT(8) /* Master function disable error */
+ #define SH4_PCIINTM_APEDIM BIT(7) /* Address parity error detection */
+ #define SH4_PCIINTM_SDIM BIT(6) /* SERR detection */
+ #define SH4_PCIINTM_DPEITWM BIT(5) /* Data parity error for target write */
+ #define SH4_PCIINTM_PEDITRM BIT(4) /* PERR detection for target read */
+ #define SH4_PCIINTM_TADIMM BIT(3) /* Target abort for master */
+ #define SH4_PCIINTM_MADIMM BIT(2) /* Master abort for master */
+ #define SH4_PCIINTM_MWPDIM BIT(1) /* Master write data parity error */
+ #define SH4_PCIINTM_MRDPEIM BIT(0) /* Master read data parity error */
+#define SH4_PCIALR 0x11C /* Error Address Register */
+#define SH4_PCICLR 0x120 /* Error Command/Data */
+ #define SH4_PCICLR_MPIO 0x80000000
+ #define SH4_PCICLR_MDMA0 0x40000000 /* DMA0 Transfer Error */
+ #define SH4_PCICLR_MDMA1 0x20000000 /* DMA1 Transfer Error */
+ #define SH4_PCICLR_MDMA2 0x10000000 /* DMA2 Transfer Error */
+ #define SH4_PCICLR_MDMA3 0x08000000 /* DMA3 Transfer Error */
+ #define SH4_PCICLR_TGT 0x04000000 /* Target Transfer Error */
+ #define SH4_PCICLR_CMDL 0x0000000F /* PCI Command at Error */
+#define SH4_PCIAINT 0x130 /* Arbiter Interrupt Register */
+ #define SH4_PCIAINT_MBKN 0x00002000 /* Master Broken Interrupt */
+ #define SH4_PCIAINT_TBTO 0x00001000 /* Target Bus Time Out */
+ #define SH4_PCIAINT_MBTO 0x00000800 /* Master Bus Time Out */
+ #define SH4_PCIAINT_TABT 0x00000008 /* Target Abort */
+ #define SH4_PCIAINT_MABT 0x00000004 /* Master Abort */
+ #define SH4_PCIAINT_RDPE 0x00000002 /* Read Data Parity Error */
+ #define SH4_PCIAINT_WDPE 0x00000001 /* Write Data Parity Error */
+#define SH4_PCIAINTM 0x134 /* Arbiter Int. Mask Register */
+#define SH4_PCIBMLR 0x138 /* Error Bus Master Register */
+ #define SH4_PCIBMLR_REQ4 0x00000010 /* REQ4 bus master at error */
+ #define SH4_PCIBMLR_REQ3 0x00000008 /* REQ3 bus master at error */
+ #define SH4_PCIBMLR_REQ2 0x00000004 /* REQ2 bus master at error */
+ #define SH4_PCIBMLR_REQ1 0x00000002 /* REQ1 bus master at error */
+ #define SH4_PCIBMLR_REQ0 0x00000001 /* REQ0 bus master at error */
+#define SH4_PCIDMABT 0x140 /* DMA Transfer Arb. Register */
+ #define SH4_PCIDMABT_RRBN 0x00000001 /* DMA Arbitor Round-Robin */
+#define SH4_PCIDPA0 0x180 /* DMA0 Transfer Addr. */
+#define SH4_PCIDLA0 0x184 /* DMA0 Local Addr. */
+#define SH4_PCIDTC0 0x188 /* DMA0 Transfer Cnt. */
+#define SH4_PCIDCR0 0x18C /* DMA0 Control Register */
+ #define SH4_PCIDCR_ALGN 0x00000600 /* DMA Alignment Mode */
+ #define SH4_PCIDCR_MAST 0x00000100 /* DMA Termination Type */
+ #define SH4_PCIDCR_INTM 0x00000080 /* DMA Interrupt Done Mask*/
+ #define SH4_PCIDCR_INTS 0x00000040 /* DMA Interrupt Done Status */
+ #define SH4_PCIDCR_LHLD 0x00000020 /* Local Address Control */
+ #define SH4_PCIDCR_PHLD 0x00000010 /* PCI Address Control*/
+ #define SH4_PCIDCR_IOSEL 0x00000008 /* PCI Address Space Type */
+ #define SH4_PCIDCR_DIR 0x00000004 /* DMA Transfer Direction */
+ #define SH4_PCIDCR_STOP 0x00000002 /* Force DMA Stop */
+ #define SH4_PCIDCR_STRT 0x00000001 /* DMA Start */
+#define SH4_PCIDPA1 0x190 /* DMA1 Transfer Addr. */
+#define SH4_PCIDLA1 0x194 /* DMA1 Local Addr. */
+#define SH4_PCIDTC1 0x198 /* DMA1 Transfer Cnt. */
+#define SH4_PCIDCR1 0x19C /* DMA1 Control Register */
+#define SH4_PCIDPA2 0x1A0 /* DMA2 Transfer Addr. */
+#define SH4_PCIDLA2 0x1A4 /* DMA2 Local Addr. */
+#define SH4_PCIDTC2 0x1A8 /* DMA2 Transfer Cnt. */
+#define SH4_PCIDCR2 0x1AC /* DMA2 Control Register */
+#define SH4_PCIDPA3 0x1B0 /* DMA3 Transfer Addr. */
+#define SH4_PCIDLA3 0x1B4 /* DMA3 Local Addr. */
+#define SH4_PCIDTC3 0x1B8 /* DMA3 Transfer Cnt. */
+#define SH4_PCIDCR3 0x1BC /* DMA3 Control Register */
+#define SH4_PCIPAR 0x1C0 /* PIO Address Register */
+ #define SH4_PCIPAR_CFGEN 0x80000000 /* Configuration Enable */
+ #define SH4_PCIPAR_BUSNO 0x00FF0000 /* Config. Bus Number */
+ #define SH4_PCIPAR_DEVNO 0x0000FF00 /* Config. Device Number */
+ #define SH4_PCIPAR_REGAD 0x000000FC /* Register Address Number */
+#define SH4_PCIMBR 0x1C4 /* Memory Base Address */
+ #define SH4_PCIMBR_MASK 0xFF000000 /* Memory Space Mask */
+ #define SH4_PCIMBR_LOCK 0x00000001 /* Lock Memory Space */
+#define SH4_PCIIOBR 0x1C8 /* I/O Base Address Register */
+ #define SH4_PCIIOBR_MASK 0xFFFC0000 /* IO Space Mask */
+ #define SH4_PCIIOBR_LOCK 0x00000001 /* Lock IO Space */
+#define SH4_PCIPINT 0x1CC /* Power Mgmnt Int. Register */
+ #define SH4_PCIPINT_D3 0x00000002 /* D3 Pwr Mgmt. Interrupt */
+ #define SH4_PCIPINT_D0 0x00000001 /* D0 Pwr Mgmt. Interrupt */
+#define SH4_PCIPINTM 0x1D0 /* Power Mgmnt Mask Register */
+#define SH4_PCICLKR 0x1D4 /* Clock Ctrl. Register */
+ #define SH4_PCICLKR_PCSTP 0x00000002 /* PCI Clock Stop */
+ #define SH4_PCICLKR_BCSTP 0x00000001 /* BCLK Clock Stop */
+/* For definitions of BCR, MCR see ... */
+#define SH4_PCIBCR1 0x1E0 /* Memory BCR1 Register */
+ #define SH4_PCIMBR0 SH4_PCIBCR1
+#define SH4_PCIBCR2 0x1E4 /* Memory BCR2 Register */
+ #define SH4_PCIMBMR0 SH4_PCIBCR2
+#define SH4_PCIWCR1 0x1E8 /* Wait Control 1 Register */
+#define SH4_PCIWCR2 0x1EC /* Wait Control 2 Register */
+#define SH4_PCIWCR3 0x1F0 /* Wait Control 3 Register */
+ #define SH4_PCIMBR2 SH4_PCIWCR3
+#define SH4_PCIMCR 0x1F4 /* Memory Control Register */
+#define SH4_PCIBCR3 0x1f8 /* Memory BCR3 Register */
+#define SH4_PCIPCTR 0x200 /* Port Control Register */
+ #define SH4_PCIPCTR_P2EN 0x000400000 /* Port 2 Enable */
+ #define SH4_PCIPCTR_P1EN 0x000200000 /* Port 1 Enable */
+ #define SH4_PCIPCTR_P0EN 0x000100000 /* Port 0 Enable */
+ #define SH4_PCIPCTR_P2UP 0x000000020 /* Port2 Pull Up Enable */
+ #define SH4_PCIPCTR_P2IO 0x000000010 /* Port2 Output Enable */
+ #define SH4_PCIPCTR_P1UP 0x000000008 /* Port1 Pull Up Enable */
+ #define SH4_PCIPCTR_P1IO 0x000000004 /* Port1 Output Enable */
+ #define SH4_PCIPCTR_P0UP 0x000000002 /* Port0 Pull Up Enable */
+ #define SH4_PCIPCTR_P0IO 0x000000001 /* Port0 Output Enable */
+#define SH4_PCIPDTR 0x204 /* Port Data Register */
+ #define SH4_PCIPDTR_PB5 0x000000020 /* Port 5 Enable */
+ #define SH4_PCIPDTR_PB4 0x000000010 /* Port 4 Enable */
+ #define SH4_PCIPDTR_PB3 0x000000008 /* Port 3 Enable */
+ #define SH4_PCIPDTR_PB2 0x000000004 /* Port 2 Enable */
+ #define SH4_PCIPDTR_PB1 0x000000002 /* Port 1 Enable */
+ #define SH4_PCIPDTR_PB0 0x000000001 /* Port 0 Enable */
+#define SH4_PCIPDR 0x220 /* Port IO Data Register */
+
+/* Platform Specific Values */
+#define SH7751_VENDOR_ID 0x1054
+#define SH7751_DEVICE_ID 0x3505
+#define SH7751R_DEVICE_ID 0x350e
+
+/* SH7751 Specific Values */
+#define SH7751_PCI_CONFIG_BASE 0xFD000000 /* Config space base addr */
+#define SH7751_PCI_CONFIG_SIZE 0x1000000 /* Config space size */
+#define SH7751_PCI_MEMORY_BASE 0xFD000000 /* Memory space base addr */
+#define SH7751_PCI_MEM_SIZE 0x01000000 /* Size of Memory window */
+#define SH7751_PCI_IO_BASE 0xFE240000 /* IO space base address */
+#define SH7751_PCI_IO_SIZE 0x40000 /* Size of IO window */
+
+#define SH7751_PCIREG_BASE 0xFE200000 /* PCI regs base address */
+
+#define SH7751_PCICONF0 0x0 /* PCI Config Reg 0 */
+ #define SH7751_PCICONF0_DEVID 0xFFFF0000 /* Device ID */
+ #define SH7751_PCICONF0_VNDID 0x0000FFFF /* Vendor ID */
+#define SH7751_PCICONF1 0x4 /* PCI Config Reg 1 */
+ #define SH7751_PCICONF1_DPE 0x80000000 /* Data Parity Error */
+ #define SH7751_PCICONF1_SSE 0x40000000 /* System Error Status */
+ #define SH7751_PCICONF1_RMA 0x20000000 /* Master Abort */
+ #define SH7751_PCICONF1_RTA 0x10000000 /* Target Abort Rx Status */
+ #define SH7751_PCICONF1_STA 0x08000000 /* Target Abort Exec Status */
+ #define SH7751_PCICONF1_DEV 0x06000000 /* Timing Status */
+ #define SH7751_PCICONF1_DPD 0x01000000 /* Data Parity Status */
+ #define SH7751_PCICONF1_FBBC 0x00800000 /* Back 2 Back Status */
+ #define SH7751_PCICONF1_UDF 0x00400000 /* User Defined Status */
+ #define SH7751_PCICONF1_66M 0x00200000 /* 66Mhz Operation Status */
+ #define SH7751_PCICONF1_PM 0x00100000 /* Power Management Status */
+ #define SH7751_PCICONF1_PBBE 0x00000200 /* Back 2 Back Control */
+ #define SH7751_PCICONF1_SER 0x00000100 /* SERR Output Control */
+ #define SH7751_PCICONF1_WCC 0x00000080 /* Wait Cycle Control */
+ #define SH7751_PCICONF1_PER 0x00000040 /* Parity Error Response */
+ #define SH7751_PCICONF1_VPS 0x00000020 /* VGA Pallet Snoop */
+ #define SH7751_PCICONF1_MWIE 0x00000010 /* Memory Write+Invalidate */
+ #define SH7751_PCICONF1_SPC 0x00000008 /* Special Cycle Control */
+ #define SH7751_PCICONF1_BUM 0x00000004 /* Bus Master Control */
+ #define SH7751_PCICONF1_MES 0x00000002 /* Memory Space Control */
+ #define SH7751_PCICONF1_IOS 0x00000001 /* I/O Space Control */
+#define SH7751_PCICONF2 0x8 /* PCI Config Reg 2 */
+ #define SH7751_PCICONF2_BCC 0xFF000000 /* Base Class Code */
+ #define SH7751_PCICONF2_SCC 0x00FF0000 /* Sub-Class Code */
+ #define SH7751_PCICONF2_RLPI 0x0000FF00 /* Programming Interface */
+ #define SH7751_PCICONF2_REV 0x000000FF /* Revision ID */
+#define SH7751_PCICONF3 0xC /* PCI Config Reg 3 */
+ #define SH7751_PCICONF3_BIST7 0x80000000 /* Bist Supported */
+ #define SH7751_PCICONF3_BIST6 0x40000000 /* Bist Executing */
+ #define SH7751_PCICONF3_BIST3_0 0x0F000000 /* Bist Passed */
+ #define SH7751_PCICONF3_HD7 0x00800000 /* Single Function device */
+ #define SH7751_PCICONF3_HD6_0 0x007F0000 /* Configuration Layout */
+ #define SH7751_PCICONF3_LAT 0x0000FF00 /* Latency Timer */
+ #define SH7751_PCICONF3_CLS 0x000000FF /* Cache Line Size */
+#define SH7751_PCICONF4 0x10 /* PCI Config Reg 4 */
+ #define SH7751_PCICONF4_BASE 0xFFFFFFFC /* I/O Space Base Addr */
+ #define SH7751_PCICONF4_ASI 0x00000001 /* Address Space Type */
+#define SH7751_PCICONF5 0x14 /* PCI Config Reg 5 */
+ #define SH7751_PCICONF5_BASE 0xFFFFFFF0 /* Mem Space Base Addr */
+ #define SH7751_PCICONF5_LAP 0x00000008 /* Prefetch Enabled */
+ #define SH7751_PCICONF5_LAT 0x00000006 /* Local Memory type */
+ #define SH7751_PCICONF5_ASI 0x00000001 /* Address Space Type */
+#define SH7751_PCICONF6 0x18 /* PCI Config Reg 6 */
+ #define SH7751_PCICONF6_BASE 0xFFFFFFF0 /* Mem Space Base Addr */
+ #define SH7751_PCICONF6_LAP 0x00000008 /* Prefetch Enabled */
+ #define SH7751_PCICONF6_LAT 0x00000006 /* Local Memory type */
+ #define SH7751_PCICONF6_ASI 0x00000001 /* Address Space Type */
+/* PCICONF7 - PCICONF10 are undefined */
+#define SH7751_PCICONF11 0x2C /* PCI Config Reg 11 */
+ #define SH7751_PCICONF11_SSID 0xFFFF0000 /* Subsystem ID */
+ #define SH7751_PCICONF11_SVID 0x0000FFFF /* Subsystem Vendor ID */
+/* PCICONF12 is undefined */
+#define SH7751_PCICONF13 0x34 /* PCI Config Reg 13 */
+ #define SH7751_PCICONF13_CPTR 0x000000FF /* PM function pointer */
+/* PCICONF14 is undefined */
+#define SH7751_PCICONF15 0x3C /* PCI Config Reg 15 */
+ #define SH7751_PCICONF15_IPIN 0x000000FF /* Interrupt Pin */
+#define SH7751_PCICONF16 0x40 /* PCI Config Reg 16 */
+ #define SH7751_PCICONF16_PMES 0xF8000000 /* PME Support */
+ #define SH7751_PCICONF16_D2S 0x04000000 /* D2 Support */
+ #define SH7751_PCICONF16_D1S 0x02000000 /* D1 Support */
+ #define SH7751_PCICONF16_DSI 0x00200000 /* Bit Device Init. */
+ #define SH7751_PCICONF16_PMCK 0x00080000 /* Clock for PME req. */
+ #define SH7751_PCICONF16_VER 0x00070000 /* PM Version */
+ #define SH7751_PCICONF16_NIP 0x0000FF00 /* Next Item Pointer */
+ #define SH7751_PCICONF16_CID 0x000000FF /* Capability Identifier */
+#define SH7751_PCICONF17 0x44 /* PCI Config Reg 17 */
+ #define SH7751_PCICONF17_DATA 0xFF000000 /* Data field for PM */
+ #define SH7751_PCICONF17_PMES 0x00800000 /* PME Status */
+ #define SH7751_PCICONF17_DSCL 0x00600000 /* Data Scaling Value */
+ #define SH7751_PCICONF17_DSEL 0x001E0000 /* Data Select */
+ #define SH7751_PCICONF17_PMEN 0x00010000 /* PME Enable */
+ #define SH7751_PCICONF17_PWST 0x00000003 /* Power State */
+/* SH7751 Internal PCI Registers */
+
+/* Memory Control Registers */
+#define SH7751_BCR1 0x0000 /* Memory BCR1 Register */
+#define SH7751_BCR2 0x0004 /* Memory BCR2 Register */
+#define SH7751_BCR3 0x0050 /* Memory BCR3 Register */
+#define SH7751_WCR1 0x0008 /* Wait Control 1 Register */
+#define SH7751_WCR2 0x000C /* Wait Control 2 Register */
+#define SH7751_WCR3 0x0010 /* Wait Control 3 Register */
+#define SH7751_MCR 0x0014 /* Memory Control Register */
+
+/* General Memory Config Addresses */
+#define SH7751_CS0_BASE_ADDR 0x0
+#define SH7751_MEM_REGION_SIZE 0x04000000
+#define SH7751_CS1_BASE_ADDR (SH7751_CS0_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS2_BASE_ADDR (SH7751_CS1_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS3_BASE_ADDR (SH7751_CS2_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS4_BASE_ADDR (SH7751_CS3_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS5_BASE_ADDR (SH7751_CS4_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+#define SH7751_CS6_BASE_ADDR (SH7751_CS5_BASE_ADDR + SH7751_MEM_REGION_SIZE)
+
+#endif /* _PCI_SH7751_H_ */
--
2.7.0
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
