Freescale has stated [1] that the LVDS clock source of the IMX6 does not pass
the PCI Gen2 clock jitter test, therefore unless an external Gen2 compliant
external clock source is present and supplied back to the IMX6 PCIe core
via LVDS CLK1/CLK2 you can not claim Gen2 compliance.
Add a dt property to specify gen1 vs gen2 and check this before allowing
a Gen2 link.
We default to Gen1 if the property is not present because at this time there
are no IMX6 boards in mainline that 'input' a clock on LVDS CLK1/CLK2.
In order to be Gen2 compliant on IMX6 you need to:
- have a Gen2 compliant external clock generator and route that clock back
to either LVDS CLK1 or LVDS CLK2 as an input.
(see IMX6SX-SabreSD reference design)
- specify this clock in the pcie node in the dt
(ie IMX6QDL_CLK_LVDS1_IN or IMX6QDL_CLK_LVDS2_IN instead of
IMX6QDL_CLK_LVDS1_GATE which configures it as a CLK output)
[1] https://community.freescale.com/message/453209
Cc: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
Cc: Bjorn Helgaas <helgaas@xxxxxxxxxx>
Cc: Fabio Estevam <fabio.estevam@xxxxxxxxxxxxx>
Cc: Zhu Richard <Richard.Zhu@xxxxxxxxxxxxx>
Cc: Akshay Bhat <akshay.bhat@xxxxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Shawn Guo <shawnguo@xxxxxxxxxx>
Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
---
v5:
- clearly default link gen to 1 when dt prop is read to avoid confusion
v4:
- rebase against linux-pci/master
- add fsl vendor prefix to dt prop
v3:
- added note in dt bindings doc that we limit to gen1 unless this is specified
as gen2 capable
- move property to imx6 pcie phy instead of designware core
- don't use &ret as temp storage as of_property_read_u32() doesn't change the
outval if property isn't found
v2:
- moved dt property to designware core
Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
---
.../devicetree/bindings/pci/fsl,imx6q-pcie.txt | 4 ++++
drivers/pci/host/pci-imx6.c | 24 +++++++++++++++-------
2 files changed, 21 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
index 3be80c6..b92fafb 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
@@ -19,6 +19,10 @@ Optional properties:
- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20
- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
+- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for
+ gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs
+ do not meet gen2 jitter requirements and thus for gen2 capability a gen2
+ compliant clock generator should be used and configured.
Example:
diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
index eb5a275..60a14b8 100644
--- a/drivers/pci/host/pci-imx6.c
+++ b/drivers/pci/host/pci-imx6.c
@@ -44,6 +44,7 @@ struct imx6_pcie {
u32 tx_deemph_gen2_6db;
u32 tx_swing_full;
u32 tx_swing_low;
+ int link_gen;
};
/* PCIe Root Complex registers (memory-mapped) */
@@ -417,11 +418,15 @@ static int imx6_pcie_establish_link(struct pcie_port *pp)
goto err_reset_phy;
}
- /* Allow Gen2 mode after the link is up. */
- tmp = readl(pp->dbi_base + PCIE_RC_LCR);
- tmp &= ~PCIE_RC_LCR_MAX_LINK_SPEEDS_MASK;
- tmp |= PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN2;
- writel(tmp, pp->dbi_base + PCIE_RC_LCR);
+ if (imx6_pcie->link_gen == 2) {
+ /* Allow Gen2 mode after the link is up. */
+ tmp = readl(pp->dbi_base + PCIE_RC_LCR);
+ tmp &= ~PCIE_RC_LCR_MAX_LINK_SPEEDS_MASK;
+ tmp |= PCIE_RC_LCR_MAX_LINK_SPEEDS_GEN2;
+ writel(tmp, pp->dbi_base + PCIE_RC_LCR);
+ } else {
+ dev_info(pp->dev, "Link: Gen2 disabled\n");
+ }
/*
* Start Directed Speed Change so the best possible speed both link
@@ -445,8 +450,7 @@ static int imx6_pcie_establish_link(struct pcie_port *pp)
}
tmp = readl(pp->dbi_base + PCIE_RC_LCSR);
- dev_dbg(pp->dev, "Link up, Gen=%i\n", (tmp >> 16) & 0xf);
-
+ dev_info(pp->dev, "Link up, Gen%i\n", (tmp >> 16) & 0xf);
return 0;
err_reset_phy:
@@ -598,6 +602,12 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
&imx6_pcie->tx_swing_low))
imx6_pcie->tx_swing_low = 127;
+ /* Limit link speed */
+ ret = of_property_read_u32(pp->dev->of_node, "fsl,max-link-speed",
+ &imx6_pcie->link_gen);
+ if (ret)
+ imx6_pcie->link_gen = 1;
+
ret = imx6_add_pcie_port(pp, pdev);
if (ret < 0)
return ret;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
