On Tue, Mar 29, 2016 at 7:50 AM, Arnd Bergmann <arnd@xxxxxxxx> wrote:
> On Tuesday 29 March 2016 07:29:34 Tim Harvey wrote:
>> On Tue, Mar 29, 2016 at 6:52 AM, Arnd Bergmann <arnd@xxxxxxxx> wrote:
>> > On Tuesday 29 March 2016 06:32:29 Tim Harvey wrote:
>
>> >> I think 31e98e0d24cd2537a63e06e235e050a06b175df7 "ARM:
>> >> imx_v6_v7_defconfig: enable PCI_MSI" should be reverted as well until
>> >> we figure this out.
>> >
>> > That doesn't sound like a helpful solution, multi_v7_defconfig for
>> > instance will still be broken because it enables PCI_MSI, and so
>> > will be all major distros.
>>
>> Arnd,
>>
>> True, but keep in mind that as far as I can tell this behavior has
>> been around since MSI was added to the IMX6 (breakage of devices that
>> use legacy irq's if MSI is enabled) which was in 3.16.
>
> I see. This part wasn't clear to me.
>
>> > What happens if we patch the pci-imx6 driver to not make use of
>> > its MSI support even when that is enabled in the kernel? Does that
>> > get both devices in your GW5xxx to work with legacy interrupts or
>> > is one or both of them still broken?
>> >
>> > Arnd
>> >
>> > diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
>> > index eb5a2755a164..d7607b2695c6 100644
>> > --- a/drivers/pci/host/pci-imx6.c
>> > +++ b/drivers/pci/host/pci-imx6.c
>> > @@ -470,7 +470,7 @@ static void imx6_pcie_host_init(struct pcie_port *pp)
>> >
>> > imx6_pcie_establish_link(pp);
>> >
>> > - if (IS_ENABLED(CONFIG_PCI_MSI))
>> > + if (0 && IS_ENABLED(CONFIG_PCI_MSI))
>> > dw_pcie_msi_init(pp);
>> > }
>> >
>> > @@ -490,7 +490,7 @@ static int __init imx6_add_pcie_port(struct pcie_port *pp,
>> > {
>> > int ret;
>> >
>> > - if (IS_ENABLED(CONFIG_PCI_MSI)) {
>> > + if (0 && IS_ENABLED(CONFIG_PCI_MSI)) {
>> > pp->msi_irq = platform_get_irq_byname(pdev, "msi");
>> > if (pp->msi_irq <= 0) {
>> > dev_err(&pdev->dev, "failed to get MSI irq\n");
>> >
>>
>> That is not enough - we would also need to disable a couple more in
>> the designware core that imx6 uses, which is also used by several
>> other SoC's. We should probably get some feedback from people with
>> those SoC's regarding MSI breaking legacy irqs.
>
> Good point. I really just meant this as an experiment, trying to
> figure out what causes it to break. I'd be surprised if the
> MSI support in the generic pcie-designware driver caused the same
> problem on the other SoCs.
>
>> PCI_MSI was enabled in imx_v6_v7_defconfig in 4.5 and enabled in
>> multi_v7_defconfig back in 3.16. PCI MSI was first introduced for the
>> IMX6 host controller in 3.16 as well. I verified that the same issue
>> exists all the way back to 3.16.
>
> Thanks for doing that research.
>
>> I don't know if its worse to disable PCI MSI for IMX6/designware all
>> the way back to 3.16 or to disable it just back to 4.5 where imx_v6_v7
>> enabled it, or perhaps just figure out the actual issue and get that
>> backported?
>
> I'd like to see the problem understood better before we talk about
> backports.
>
> One thing I just noticed is that the same GPC interrupt line (GIC_SPI
> 120) is used for MSI and for IntD. Maybe there is something going on with
> sharing an interrupt line between a nested irqchip and a device?
>
> Could this be a bug in the generic IRQ handling code? Can you check
> which interrupt the broken device(s) on your machine are using? Is
> it always the 120 (IntD) line, or are the other three lines broken
> as well? I don't actually know how to look it up, but the 'lspci -t'
> output should let us reconstruct the swizzling manually.
>
> Arnd
Arnd,
Right, on the IMX the MSI interrupt is GIC-120 which is also the
legacy INTD and I do see that if I happen to put a radio in a slot
where due to swizzling its pin1 becomes INTD (GIC-120) the interrupt
does fire and the device works. Any other slot using GIC-123 (INTA),
GIC-122 (INTB), or GIC-121 (INTC) never fires so its very possible
that something in the designware core is masking out the legacy irqs.
I would also think this was something IMX specific, but I really don't
see any codepaths in pci-imx6.c that would cause that: a driver
requesting a legacy PCI would get a GIC interrupt which is handled by
the IMX6 gpc interrupt controller.
Any dra7xxx, exynos, spear13xx, keystone, layerscape, hisi, qcom SoC
users of designware PCIe core out there that can verify PCI MSI and
legacy are both working at the same time?
Lucas is the expert here and I believe he has the documentation for
the designware core that Freescale doens't provide with the IMX6
documentation so hopefully he can provide some insight. He's the one
that has authored all the MSI support and has been using it.
I typically advise our users to 'not' enable MSI because
architecturally you can spread 4 distinct legacy irq's across CPU's
better than a single shared irq.
Tim
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
