On 3/14/2016 10:36 PM, Bjorn Helgaas wrote:
> On Mon, Mar 14, 2016 at 10:28:11PM -0400, Sinan Kaya wrote:
>> On 3/14/2016 9:48 PM, Bjorn Helgaas wrote:
>>
>> Yes. I was talking about PCIe on ARM64.
>>
>>> If you go to Fry's and buy a conventional PCI card, it is going to
>>> pull INTA# low to assert an interrupt. It doesn't matter whether you
>>> put it in an x86 system or an arm64 system.
>>
>> I don't see INTA# of the PCIe card at the system level. The PCIe wire
>> interrupt gets converted to the system level interrupt by the PCIe controller.
>
> That's why I said *conventional PCI*. If you have a conventional PCI
> device below either a conventional PCI host controller or a PCIe-to-PCI
> bridge, there are real INTx wires, not virtual wires, and they are
> level/low. But I think you pointed out the key below (that the
> Interrupt resource in a PNP0C0F device encodes the trigger type).
>
>>>>> I pasted the code here again. It looks like you want to validate that
>>>>> PCI interrupts are always level low.
>>> I don't really care whether PCI interrupts are always level low. What
>>> matters is that the PCI interrupt line matches the configuration of
>>> the interrupt controller input.
>>>
>>
>> Agreed. But the interrupt controller configuration is system specific. How would
>> you check interrupt line against what the interrupt controller requires
>> on each architecture as this is common code?
>>
>>
>>> If the PCI interrupt can be a different type, e.g., level high, and
>>> there's a way to discover that, we can check that against the
>>> interrupt controller configuration.
>>>
>>> This is all in the context of conventional PCI, and we're probably
>>> talking about arm64 PCIe systems, not conventional PCI.
>>
>> INTx interrupts are TLP messages on PCIe as you already know. There is no INTA
>> interrupt wire.
>
> Yes, that's why I mentioned PCIe sec 2.2.8.1 below.
>
>> "6.1.2. PCI Compatible INTx Emulation" section of the PCIe spec describes
>> INTx emulation on PCIe.
>> ...
>>
>>> I'm not sure what an Interrupt Link device means in PCIe. I suppose it would have
>>> to connect an INTx virtual wire to a system interrupt? The PCIe spec
>>> says this sort of mapping is system implementation specific (r3.0, sec
>>> 2.2.8.1).
>>
>> The INTx messages are converted to the system interrupt by the PCIe controller.
>> The interrupt type between the PCIe controller and the ARM GIC interrupt
>> controller is dictated by the ARM GIC Interrupt Controller Specification for
>> ARM64.
>>
>> Here is what ACPI table looks like for reference
>>
>> Name(_PRT, Package(){
>> Package(){0x0FFFF, 0, \_SB.LN0A, 0}, // Slot 0, INTA
>> Package(){0x0FFFF, 1, \_SB.LN0B, 0}, // Slot 0, INTB
>> Package(){0x0FFFF, 2, \_SB.LN0C, 0}, // Slot 0, INTC
>> Package(){0x0FFFF, 3, \_SB.LN0D, 0} // Slot 0, INTD
>> })
>>
>> Device(LN0A){
>> Name(_HID, EISAID("PNP0C0F")) // PCI interrupt link
>> Name(_UID, 1)
>> Name(_PRS, ResourceTemplate(){
>> Interrupt(ResourceProducer, Level, ActiveHigh, Exclusive, , ,) {0x123}
>> })
>
> I forgot that the link already include the trigger mode in it. Maybe we
> can check for that instead of assuming level/low.
>
Let me explore this area.
> Bjorn
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
Sinan Kaya
Qualcomm Technologies, Inc. on behalf of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
