Re: [Bugfix 0/3] Convert eata driver to a normal PCI device driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





Jiang Liu wrote on 14/09/15 12:38:
Hi Authur,
	As suggested by Bjorn, patch 1-2 set implement a PCI device
driver to manage eata PCI devices. And patch 3 tries to support PCI
device hot-removal for eata, but I have no change to test due to
limited knowledge about scsi subsystem and lacking of hardware for
tests.
	So you could please help to test patch 1-2? Patch 3 is just
for comments.
Thanks!
Gerry

Jiang Liu (3):
   eata: Use IDA to manage eata board IDs
   eata: Implement PCI driver to manage eata PCI devices
   eata: Enhance eata driver to support PCI device hot-removal

  drivers/scsi/eata.c |  232 +++++++++++++++++++++++++++------------------------
  1 file changed, 125 insertions(+), 107 deletions(-)


With patches 1 and 2 applied, I get a successful boot with IRQ mapping:

[    1.147056] EATA0: IRQ 10 mapped to IO-APIC IRQ 17.
[    1.160404] EATA/DMA 2.0x: Copyright (C) 1994-2003 Dario Ballabio.
[ 1.160469] EATA config options -> tm:1, lc:y, mq:16, rs:y, et:n, ip:n, ep:n, pp:y.
[    1.160541] EATA0: 2.0C, PCI 0xd890, IRQ 17, BMST, SG 122, MB 64.
[    1.160600] EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
[    1.160658] EATA0: SCSI channel 0 enabled, host target ID 7.
[    1.161207] scsi host0: EATA/DMA 2.0x rev. 8.10.00


but I still get errors when trying to do a kexec reboot, see http://www.users.on.net/~arthur.marsh/20150915547.jpg

roughly it reads (after the synchronising SCSI cache reboot messages) and a long period of a dark screen:

sd 0:0:6:0: abort, mbox 63.
EATA0: abort, mbox 63 is in use.
sd 0:0:6:0: reset, enter.
EATA0: reset, mbox 63 in reset.
EATA0: reset, board reset done, enabling interrupts.
EATA0: reset, interrupts disabled, loops 100469.
EATA0: reset, mbox 63 locked, DID_RESET, done.
EATA0: reset, exit, done.
sd 0:0:6:0: qcomm, mbox 0, adapter busy, will start
sd 0:0:6:0: abort, mbox 0.
EATA0: abort, timeout error.
sd 0:0:6:0: reset, enter.
EATA0: reset, exit, timeout error.
sd 0:0:6:0 Device offlinled - not ready after error recovery
sd 0:0:6:0 rejecting I/O to offline device
sd 0:0:6:0 rejecting I/O to offline device
sd 0:0:6:0 [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
starting new kernel

It would be great if this problem could be fixed.

Arthur.

--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux