Am Freitag, den 11.09.2015, 09:08 -0300 schrieb Fabio Estevam:
> From: Fabio Estevam <fabio.estevam@xxxxxxxxxxxxx>
>
> Instead of having some hardcoded values, it is preferred to use
> defines when possible.
>
> Signed-off-by: Fabio Estevam <fabio.estevam@xxxxxxxxxxxxx>
Reviewed-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> ---
> Changes since v1:
> - Make clear that the defines represent bitfields (Lucas)
>
> drivers/pci/host/pci-imx6.c | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
> index 2d0d0fe..6f43086 100644
> --- a/drivers/pci/host/pci-imx6.c
> +++ b/drivers/pci/host/pci-imx6.c
> @@ -55,6 +55,7 @@ struct imx6_pcie {
> #define PCIE_PL_PFLR_LINK_STATE_MASK (0x3f << 16)
> #define PCIE_PL_PFLR_FORCE_LINK (1 << 15)
> #define PCIE_PHY_DEBUG_R0 (PL_OFFSET + 0x28)
> +#define PCIE_PHY_DEBUG_R0_LTSSM_MASK (0x3f << 0)
> #define PCIE_PHY_DEBUG_R1 (PL_OFFSET + 0x2c)
> #define PCIE_PHY_DEBUG_R1_XMLH_LINK_IN_TRAINING (1 << 29)
> #define PCIE_PHY_DEBUG_R1_XMLH_LINK_UP (1 << 4)
> @@ -74,6 +75,7 @@ struct imx6_pcie {
>
> /* PHY registers (not memory-mapped) */
> #define PCIE_PHY_RX_ASIC_OUT 0x100D
> +#define PCIE_PHY_RX_ASIC_OUT_VALID (1 << 0)
>
> #define PHY_RX_OVRD_IN_LO 0x1005
> #define PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5)
> @@ -503,10 +505,10 @@ static int imx6_pcie_link_up(struct pcie_port *pp)
> pcie_phy_read(pp->dbi_base, PCIE_PHY_RX_ASIC_OUT, &rx_valid);
> debug_r0 = readl(pp->dbi_base + PCIE_PHY_DEBUG_R0);
>
> - if (rx_valid & 0x01)
> + if (rx_valid & PCIE_PHY_RX_ASIC_OUT_VALID)
> return 0;
>
> - if ((debug_r0 & 0x3f) != 0x0d)
> + if ((debug_r0 & PCIE_PHY_DEBUG_R0_LTSSM_MASK) != 0x0d)
> return 0;
>
> dev_err(pp->dev, "transition to gen2 is stuck, reset PHY!\n");
--
Pengutronix e.K. | Lucas Stach |
Industrial Linux Solutions | http://www.pengutronix.de/ |
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
