Hi Jörg,
I attached the dmesg output of the boot seuqence. This time after
reboot, the amount of IO_PAGE_FAULTs is not that much, but now, I got a
few ata3.00 errors.
Am 21.07.2015 um 17:56 schrieb Joerg Roedel:
> Hi Andreas,
>
> On Tue, Jul 21, 2015 at 09:34:46AM -0600, Alex Williamson wrote:
>>> Since Linux 4.1, I'm getting a lot of IO_PAGE_FAULT like this one
To be more precise: The last kernel w/o this problem is 3.18.x - I never
used 3.19 or 4.0.
[...]
> These addresses are not returned from the address allocator of the AMD
> IOMMU driver. Hard to tell what went wrong here, can you probably get a
> complete boot-log (dmesg output after boot) and send it to me?
>
> Please also boot with amd_iommu_dump on the kernel command line.
Thanks,
Andreas
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 4.1.2-1.1-desktop (geeko@buildhost) (gcc version 4.8.1 20130909 [gcc-4_8-branch revision 202388] (SUSE Linux) ) #1 SMP PREEMPT Tue Jun 30 11:16:29 CEST 2015 (a46abf6)
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-4.1.2-1.1-desktop root=/dev/mapper/ssd1-newUsr resume=/dev/raid0/swap splash=silent quiet showopts amd_iommu_dump
[ 0.000000] tseg: 00cff00000
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000097fff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000cfd9ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000cfda0000-0x00000000cfdd0fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000cfdd1000-0x00000000cfdfffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000cfe00000-0x00000000cfefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000062effffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Gigabyte Technology Co., Ltd. GA-990XA-UD3/GA-990XA-UD3, BIOS F14b 01/24/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] e820: last_pfn = 0x62f000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
[ 0.000000] 1 base 000080000000 mask FFFFC0000000 write-back
[ 0.000000] 2 base 0000C0000000 mask FFFFF0000000 write-back
[ 0.000000] 3 base 0000CFE00000 mask FFFFFFE00000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] TOM2: 000000062f000000 aka 25328M
[ 0.000000] PAT configuration [0-7]: WB WC UC- UC WB WC UC- UC
[ 0.000000] e820: update [mem 0xcfe00000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xcfda0 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f4be0-0x000f4bef] mapped at [ffff8800000f4be0]
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff880000092000] 92000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x02225000, 0x02225fff] PGTABLE
[ 0.000000] BRK [0x02226000, 0x02226fff] PGTABLE
[ 0.000000] BRK [0x02227000, 0x02227fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x62ee00000-0x62effffff]
[ 0.000000] [mem 0x62ee00000-0x62effffff] page 2M
[ 0.000000] BRK [0x02228000, 0x02228fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x620000000-0x62edfffff]
[ 0.000000] [mem 0x620000000-0x62edfffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x600000000-0x61fffffff]
[ 0.000000] [mem 0x600000000-0x61fffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0xcfd9ffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0xbfffffff] page 1G
[ 0.000000] [mem 0xc0000000-0xcfbfffff] page 2M
[ 0.000000] [mem 0xcfc00000-0xcfd9ffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x5ffffffff]
[ 0.000000] [mem 0x100000000-0x5ffffffff] page 1G
[ 0.000000] RAMDISK: [mem 0x36a6c000-0x3752dfff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F6B00 000014 (v00 GBT )
[ 0.000000] ACPI: RSDT 0x00000000CFDD1000 000050 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: FACP 0x00000000CFDD1080 000074 (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: DSDT 0x00000000CFDD1100 007A4B (v01 GBT GBTUACPI 00001000 MSFT 03000000)
[ 0.000000] ACPI: FACS 0x00000000CFDA0000 000040
[ 0.000000] ACPI: MSDM 0x00000000CFDD8C40 000055 (v03 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: HPET 0x00000000CFDD8CC0 000038 (v01 GBT GBTUACPI 42302E31 GBTU 00000098)
[ 0.000000] ACPI: MCFG 0x00000000CFDD8D00 00003C (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: EUDS 0x00000000CFDD8D80 000740 (v01 GBT 00000000 00000000)
[ 0.000000] ACPI: MATS 0x00000000CFDD94C0 000034 (v01 GBT 00000000 00000000)
[ 0.000000] ACPI: TAMG 0x00000000CFDD9530 000182 (v01 GBT GBT B0 5455312E BG?? 53450101)
[ 0.000000] ACPI: APIC 0x00000000CFDD8B80 0000BC (v01 GBT GBTUACPI 42302E31 GBTU 01010101)
[ 0.000000] ACPI: MATS 0x00000000CFDD96C0 006209 (v01 MATS RCM 80000001 INTL 20061109)
[ 0.000000] ACPI: SSDT 0x00000000CFDDF940 001714 (v01 AMD POWERNOW 00000001 AMD 00000001)
[ 0.000000] ACPI: IVRS 0x00000000CFDE10D0 0000E0 (v01 AMD RD890S 00202031 AMD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000062effffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x62efea000-0x62effdfff]
[ 0.000000] [ffffea0000000000-ffffea0018bfffff] PMD -> [ffff880616600000-ffff88062e5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000062effffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x0000000000097fff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000cfd9ffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000062effffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000062effffff]
[ 0.000000] On node 0 totalpages: 6286647
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3991 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13239 pages used for memmap
[ 0.000000] DMA32 zone: 847264 pages, LIFO batch:31
[ 0.000000] Normal zone: 84928 pages used for memmap
[ 0.000000] Normal zone: 5435392 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] dfl dfl lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 8, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00098000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcfda0000-0xcfdd0fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcfdd1000-0xcfdfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcfe00000-0xcfefffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xcff00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
[ 0.000000] e820: [mem 0xcff00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 33 pages/cpu @ffff88062ec00000 s97432 r8192 d29544 u262144
[ 0.000000] pcpu-alloc: s97432 r8192 d29544 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 6188395
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-4.1.2-1.1-desktop root=/dev/mapper/ssd1-newUsr resume=/dev/raid0/swap splash=silent quiet showopts amd_iommu_dump
[ 0.000000] log_buf_len individual max cpu contribution: 32768 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 229376 bytes
[ 0.000000] log_buf_len min size: 262144 bytes
[ 0.000000] log_buf_len: 524288 bytes
[ 0.000000] early log buf free: 251924(96%)
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form
[ 0.000000] AGP: Checking aperture...
[ 0.000000] AGP: No AGP bridge found
[ 0.000000] AGP: Node 0: aperture [bus addr 0xc4000000-0xc5ffffff] (32MB)
[ 0.000000] Aperture pointing to e820 RAM. Ignoring.
[ 0.000000] AGP: Your BIOS doesn't leave a aperture memory hole
[ 0.000000] AGP: Please enable the IOMMU option in the BIOS setup
[ 0.000000] AGP: This costs you 64MB of RAM
[ 0.000000] AGP: Mapping aperture over RAM [mem 0xc4000000-0xc7ffffff] (65536KB)
[ 0.000000] PM: Registered nosave memory: [mem 0xc4000000-0xc7ffffff]
[ 0.000000] Memory: 24590172K/25146588K available (6819K kernel code, 1120K rwdata, 4996K rodata, 1564K init, 1520K bss, 556416K reserved, 0K cma-reserved)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=8.
[ 0.000000] RCU kthread priority: 1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
[ 0.000000] NR_IRQS:33024 nr_irqs:488 16
[ 0.000000] Offload RCU callbacks from all CPUs
[ 0.000000] Offload RCU callbacks from CPUs: 0-7.
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484873504 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 4026.993 MHz processor
[ 0.000020] Calibrating delay loop (skipped), value calculated using timer frequency.. 8053.98 BogoMIPS (lpj=4026993)
[ 0.000022] pid_max: default: 32768 minimum: 301
[ 0.000029] ACPI: Core revision 20150410
[ 0.004786] ACPI: All ACPI Tables successfully acquired
[ 0.062420] Security Framework initialized
[ 0.062433] AppArmor: AppArmor initialized
[ 0.064272] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes)
[ 0.815776] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.819137] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.819176] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.819548] Initializing cgroup subsys blkio
[ 0.819551] Initializing cgroup subsys memory
[ 0.819558] Initializing cgroup subsys devices
[ 0.819561] Initializing cgroup subsys freezer
[ 0.819563] Initializing cgroup subsys net_cls
[ 0.819566] Initializing cgroup subsys perf_event
[ 0.819568] Initializing cgroup subsys net_prio
[ 0.819570] Initializing cgroup subsys hugetlb
[ 0.819588] CPU: Physical Processor ID: 0
[ 0.819589] CPU: Processor Core ID: 0
[ 0.819590] mce: CPU supports 7 MCE banks
[ 0.819596] LVT offset 1 assigned for vector 0xf9
[ 0.819601] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
[ 0.819602] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
[ 0.819686] Freeing SMP alternatives memory: 24K (ffffffff820a1000 - ffffffff820a7000)
[ 0.820253] ftrace: allocating 25803 entries in 101 pages
[ 0.826708] AMD-Vi: device: 00:00.2 cap: 0040 seg: 0 flags: 3e info 1300
[ 0.826709] AMD-Vi: mmio-addr: 00000000fec30000
[ 0.826720] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:00.0 flags: 00
[ 0.826721] AMD-Vi: DEV_RANGE_END devid: 00:00.2
[ 0.826722] AMD-Vi: DEV_SELECT devid: 00:02.0 flags: 00
[ 0.826723] AMD-Vi: DEV_SELECT_RANGE_START devid: 01:00.0 flags: 00
[ 0.826724] AMD-Vi: DEV_RANGE_END devid: 01:00.1
[ 0.826725] AMD-Vi: DEV_SELECT devid: 00:04.0 flags: 00
[ 0.826726] AMD-Vi: DEV_SELECT devid: 02:00.0 flags: 00
[ 0.826727] AMD-Vi: DEV_SELECT devid: 00:05.0 flags: 00
[ 0.826727] AMD-Vi: DEV_SELECT devid: 03:00.0 flags: 00
[ 0.826728] AMD-Vi: DEV_SELECT devid: 00:09.0 flags: 00
[ 0.826729] AMD-Vi: DEV_SELECT devid: 04:00.0 flags: 00
[ 0.826730] AMD-Vi: DEV_SELECT devid: 00:0a.0 flags: 00
[ 0.826731] AMD-Vi: DEV_SELECT devid: 05:00.0 flags: 00
[ 0.826732] AMD-Vi: DEV_SELECT devid: 00:11.0 flags: 00
[ 0.826732] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:12.0 flags: 00
[ 0.826733] AMD-Vi: DEV_RANGE_END devid: 00:12.2
[ 0.826734] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:13.0 flags: 00
[ 0.826735] AMD-Vi: DEV_RANGE_END devid: 00:13.2
[ 0.826736] AMD-Vi: DEV_SELECT devid: 00:14.0 flags: d7
[ 0.826737] AMD-Vi: DEV_SELECT devid: 00:14.2 flags: 00
[ 0.826737] AMD-Vi: DEV_SELECT devid: 00:14.3 flags: 00
[ 0.826738] AMD-Vi: DEV_SELECT devid: 00:14.4 flags: 00
[ 0.826739] AMD-Vi: DEV_ALIAS_RANGE devid: 06:00.0 flags: 00 devid_to: 00:14.4
[ 0.826740] AMD-Vi: DEV_RANGE_END devid: 06:1f.7
[ 0.826746] AMD-Vi: DEV_SELECT devid: 00:14.5 flags: 00
[ 0.826747] AMD-Vi: DEV_SELECT devid: 00:15.0 flags: 00
[ 0.826748] AMD-Vi: DEV_SELECT_RANGE_START devid: 07:00.0 flags: 00
[ 0.826749] AMD-Vi: DEV_RANGE_END devid: 07:1f.7
[ 0.826753] AMD-Vi: DEV_SELECT_RANGE_START devid: 00:16.0 flags: 00
[ 0.826753] AMD-Vi: DEV_RANGE_END devid: 00:16.2
[ 0.826755] AMD-Vi: DEV_SPECIAL(IOAPIC[8]) devid: 00:14.0
[ 0.826756] AMD-Vi: DEV_SPECIAL(HPET[0]) devid: 00:14.0
[ 0.826757] AMD-Vi: DEV_SPECIAL(IOAPIC[8]) devid: 00:00.1
[ 0.899479] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 1.010947] smpboot: CPU0: AMD FX(tm)-8350 Eight-Core Processor (fam: 15, model: 02, stepping: 00)
[ 1.010964] Performance Events: Fam15h core perfctr, AMD PMU driver.
[ 1.010968] ... version: 0
[ 1.010969] ... bit width: 48
[ 1.010969] ... generic registers: 6
[ 1.010970] ... value mask: 0000ffffffffffff
[ 1.010971] ... max period: 00007fffffffffff
[ 1.010972] ... fixed-purpose events: 0
[ 1.010973] ... event mask: 000000000000003f
[ 1.019002] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 1.021046] x86: Booting SMP configuration:
[ 1.021048] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
[ 1.124041] x86: Booted up 1 node, 8 CPUs
[ 1.124044] smpboot: Total of 8 processors activated (64431.88 BogoMIPS)
[ 1.133802] devtmpfs: initialized
[ 1.138802] PM: Registering ACPI NVS region [mem 0xcfda0000-0xcfdd0fff] (200704 bytes)
[ 1.138889] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 1.138986] pinctrl core: initialized pinctrl subsystem
[ 1.139013] RTC time: 16:08:13, date: 07/21/15
[ 1.139117] NET: Registered protocol family 16
[ 1.141823] cpuidle: using governor ladder
[ 1.144810] cpuidle: using governor menu
[ 1.144888] ACPI: bus type PCI registered
[ 1.144889] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.144962] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 1.144964] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 1.145239] PCI: Using configuration type 1 for base access
[ 1.145830] mtrr: your CPUs had inconsistent variable MTRR settings
[ 1.145831] mtrr: probably your BIOS does not setup all CPUs.
[ 1.145832] mtrr: corrected configuration.
[ 1.150232] ACPI: Added _OSI(Module Device)
[ 1.150234] ACPI: Added _OSI(Processor Device)
[ 1.150235] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 1.150236] ACPI: Added _OSI(Processor Aggregator Device)
[ 1.162963] ACPI: Interpreter enabled
[ 1.162970] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20150410/hwxface-580)
[ 1.162975] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20150410/hwxface-580)
[ 1.162990] ACPI: (supports S0 S3 S4 S5)
[ 1.162991] ACPI: Using IOAPIC for interrupt routing
[ 1.163023] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.168882] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.168888] acpi PNP0A03:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
[ 1.168893] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 1.169268] PCI host bridge to bus 0000:00
[ 1.169271] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.169273] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 1.169274] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 1.169276] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 1.169278] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff window]
[ 1.169279] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff window]
[ 1.169281] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfebfffff window]
[ 1.169288] pci 0000:00:00.0: [1002:5a14] type 00 class 0x060000
[ 1.169299] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size)
[ 1.169415] pci 0000:00:00.2: [1002:5a23] type 00 class 0x080600
[ 1.169532] pci 0000:00:02.0: [1002:5a16] type 01 class 0x060400
[ 1.169561] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 1.169632] pci 0000:00:02.0: System wakeup disabled by ACPI
[ 1.169670] pci 0000:00:04.0: [1002:5a18] type 01 class 0x060400
[ 1.169698] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 1.169767] pci 0000:00:04.0: System wakeup disabled by ACPI
[ 1.169804] pci 0000:00:05.0: [1002:5a19] type 01 class 0x060400
[ 1.169831] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[ 1.169900] pci 0000:00:05.0: System wakeup disabled by ACPI
[ 1.169937] pci 0000:00:09.0: [1002:5a1c] type 01 class 0x060400
[ 1.169965] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
[ 1.170037] pci 0000:00:09.0: System wakeup disabled by ACPI
[ 1.170073] pci 0000:00:0a.0: [1002:5a1d] type 01 class 0x060400
[ 1.170101] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold
[ 1.170169] pci 0000:00:0a.0: System wakeup disabled by ACPI
[ 1.170212] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601
[ 1.170225] pci 0000:00:11.0: reg 0x10: [io 0xff00-0xff07]
[ 1.170232] pci 0000:00:11.0: reg 0x14: [io 0xfe00-0xfe03]
[ 1.170238] pci 0000:00:11.0: reg 0x18: [io 0xfd00-0xfd07]
[ 1.170245] pci 0000:00:11.0: reg 0x1c: [io 0xfc00-0xfc03]
[ 1.170252] pci 0000:00:11.0: reg 0x20: [io 0xfb00-0xfb0f]
[ 1.170259] pci 0000:00:11.0: reg 0x24: [mem 0xfdfff000-0xfdfff3ff]
[ 1.170379] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
[ 1.170389] pci 0000:00:12.0: reg 0x10: [mem 0xfdffe000-0xfdffefff]
[ 1.170498] pci 0000:00:12.0: System wakeup disabled by ACPI
[ 1.170537] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
[ 1.170549] pci 0000:00:12.2: reg 0x10: [mem 0xfdffd000-0xfdffd0ff]
[ 1.170604] pci 0000:00:12.2: supports D1 D2
[ 1.170606] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 1.170673] pci 0000:00:12.2: System wakeup disabled by ACPI
[ 1.170714] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
[ 1.170724] pci 0000:00:13.0: reg 0x10: [mem 0xfdffc000-0xfdffcfff]
[ 1.170831] pci 0000:00:13.0: System wakeup disabled by ACPI
[ 1.170871] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
[ 1.170883] pci 0000:00:13.2: reg 0x10: [mem 0xfdffb000-0xfdffb0ff]
[ 1.170937] pci 0000:00:13.2: supports D1 D2
[ 1.170939] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 1.171007] pci 0000:00:13.2: System wakeup disabled by ACPI
[ 1.171046] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[ 1.171187] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[ 1.171201] pci 0000:00:14.2: reg 0x10: [mem 0xfdff4000-0xfdff7fff 64bit]
[ 1.171248] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 1.171317] pci 0000:00:14.2: System wakeup disabled by ACPI
[ 1.171353] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
[ 1.171494] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[ 1.171584] pci 0000:00:14.4: System wakeup disabled by ACPI
[ 1.171619] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
[ 1.171629] pci 0000:00:14.5: reg 0x10: [mem 0xfdffa000-0xfdffafff]
[ 1.171737] pci 0000:00:14.5: System wakeup disabled by ACPI
[ 1.171778] pci 0000:00:15.0: [1002:43a0] type 01 class 0x060400
[ 1.171824] pci 0000:00:15.0: supports D1 D2
[ 1.171894] pci 0000:00:15.0: System wakeup disabled by ACPI
[ 1.171930] pci 0000:00:16.0: [1002:4397] type 00 class 0x0c0310
[ 1.171940] pci 0000:00:16.0: reg 0x10: [mem 0xfdff9000-0xfdff9fff]
[ 1.172048] pci 0000:00:16.0: System wakeup disabled by ACPI
[ 1.172088] pci 0000:00:16.2: [1002:4396] type 00 class 0x0c0320
[ 1.172101] pci 0000:00:16.2: reg 0x10: [mem 0xfdff8000-0xfdff80ff]
[ 1.172156] pci 0000:00:16.2: supports D1 D2
[ 1.172157] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 1.172225] pci 0000:00:16.2: System wakeup disabled by ACPI
[ 1.172265] pci 0000:00:18.0: [1022:1600] type 00 class 0x060000
[ 1.172363] pci 0000:00:18.1: [1022:1601] type 00 class 0x060000
[ 1.172457] pci 0000:00:18.2: [1022:1602] type 00 class 0x060000
[ 1.172550] pci 0000:00:18.3: [1022:1603] type 00 class 0x060000
[ 1.172645] pci 0000:00:18.4: [1022:1604] type 00 class 0x060000
[ 1.172740] pci 0000:00:18.5: [1022:1605] type 00 class 0x060000
[ 1.172875] pci 0000:01:00.0: [1002:6759] type 00 class 0x030000
[ 1.172890] pci 0000:01:00.0: reg 0x10: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 1.172900] pci 0000:01:00.0: reg 0x18: [mem 0xfdec0000-0xfdedffff 64bit]
[ 1.172907] pci 0000:01:00.0: reg 0x20: [io 0xee00-0xeeff]
[ 1.172919] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
[ 1.172952] pci 0000:01:00.0: supports D1 D2
[ 1.173008] pci 0000:01:00.1: [1002:aa90] type 00 class 0x040300
[ 1.173022] pci 0000:01:00.1: reg 0x10: [mem 0xfdefc000-0xfdefffff 64bit]
[ 1.173082] pci 0000:01:00.1: supports D1 D2
[ 1.175324] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 1.175328] pci 0000:00:02.0: bridge window [io 0xe000-0xefff]
[ 1.175330] pci 0000:00:02.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 1.175333] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 1.175374] pci 0000:02:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 1.175390] pci 0000:02:00.0: reg 0x10: [mem 0xfddf8000-0xfddfffff 64bit]
[ 1.175457] pci 0000:02:00.0: supports D1 D2
[ 1.175458] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.177321] pci 0000:00:04.0: PCI bridge to [bus 02]
[ 1.177324] pci 0000:00:04.0: bridge window [io 0xd000-0xdfff]
[ 1.177326] pci 0000:00:04.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 1.177329] pci 0000:00:04.0: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[ 1.177373] pci 0000:03:00.0: [168c:0030] type 00 class 0x028000
[ 1.177390] pci 0000:03:00.0: reg 0x10: [mem 0xfdbc0000-0xfdbdffff 64bit]
[ 1.177427] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.177470] pci 0000:03:00.0: supports D1
[ 1.177472] pci 0000:03:00.0: PME# supported from D0 D1 D3hot
[ 1.179316] pci 0000:00:05.0: PCI bridge to [bus 03]
[ 1.179320] pci 0000:00:05.0: bridge window [io 0xc000-0xcfff]
[ 1.179322] pci 0000:00:05.0: bridge window [mem 0xfdb00000-0xfdbfffff]
[ 1.179324] pci 0000:00:05.0: bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[ 1.179368] pci 0000:04:00.0: [10ec:8168] type 00 class 0x020000
[ 1.179381] pci 0000:04:00.0: reg 0x10: [io 0xbe00-0xbeff]
[ 1.179401] pci 0000:04:00.0: reg 0x18: [mem 0xfd6ff000-0xfd6fffff 64bit pref]
[ 1.179414] pci 0000:04:00.0: reg 0x20: [mem 0xfd6f8000-0xfd6fbfff 64bit pref]
[ 1.179469] pci 0000:04:00.0: supports D1 D2
[ 1.179470] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.181316] pci 0000:00:09.0: PCI bridge to [bus 04]
[ 1.181319] pci 0000:00:09.0: bridge window [io 0xb000-0xbfff]
[ 1.181321] pci 0000:00:09.0: bridge window [mem 0xfd900000-0xfd9fffff]
[ 1.181324] pci 0000:00:09.0: bridge window [mem 0xfd600000-0xfd6fffff 64bit pref]
[ 1.181366] pci 0000:05:00.0: [1b6f:7023] type 00 class 0x0c0330
[ 1.181382] pci 0000:05:00.0: reg 0x10: [mem 0xfd3f8000-0xfd3fffff 64bit]
[ 1.181450] pci 0000:05:00.0: supports D1 D2
[ 1.181452] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.183312] pci 0000:00:0a.0: PCI bridge to [bus 05]
[ 1.183315] pci 0000:00:0a.0: bridge window [io 0xa000-0xafff]
[ 1.183317] pci 0000:00:0a.0: bridge window [mem 0xfd300000-0xfd3fffff]
[ 1.183320] pci 0000:00:0a.0: bridge window [mem 0xfd200000-0xfd2fffff 64bit pref]
[ 1.183361] pci 0000:06:06.0: [8086:1229] type 00 class 0x020000
[ 1.183377] pci 0000:06:06.0: reg 0x10: [mem 0xfd8ff000-0xfd8fffff]
[ 1.183387] pci 0000:06:06.0: reg 0x14: [io 0x9f00-0x9f3f]
[ 1.183396] pci 0000:06:06.0: reg 0x18: [mem 0xfd8c0000-0xfd8dffff]
[ 1.183430] pci 0000:06:06.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 1.183459] pci 0000:06:06.0: supports D1 D2
[ 1.183460] pci 0000:06:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.183517] pci 0000:06:0e.0: [1106:3044] type 00 class 0x0c0010
[ 1.183534] pci 0000:06:0e.0: reg 0x10: [mem 0xfd8fe000-0xfd8fe7ff]
[ 1.183544] pci 0000:06:0e.0: reg 0x14: [io 0x9e00-0x9e7f]
[ 1.183616] pci 0000:06:0e.0: supports D2
[ 1.183617] pci 0000:06:0e.0: PME# supported from D2 D3hot D3cold
[ 1.183678] pci 0000:00:14.4: PCI bridge to [bus 06] (subtractive decode)
[ 1.183681] pci 0000:00:14.4: bridge window [io 0x9000-0x9fff]
[ 1.183684] pci 0000:00:14.4: bridge window [mem 0xfd800000-0xfd8fffff]
[ 1.183687] pci 0000:00:14.4: bridge window [mem 0xfd700000-0xfd7fffff pref]
[ 1.183688] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7 window] (subtractive decode)
[ 1.183690] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff window] (subtractive decode)
[ 1.183691] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff window] (subtractive decode)
[ 1.183693] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff window] (subtractive decode)
[ 1.183694] pci 0000:00:14.4: bridge window [mem 0xfed40000-0xfed44fff window] (subtractive decode)
[ 1.183696] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xfebfffff window] (subtractive decode)
[ 1.183736] pci 0000:00:15.0: PCI bridge to [bus 07]
[ 1.183740] pci 0000:00:15.0: bridge window [io 0x8000-0x8fff]
[ 1.183742] pci 0000:00:15.0: bridge window [mem 0xfd500000-0xfd5fffff]
[ 1.183746] pci 0000:00:15.0: bridge window [mem 0xfd400000-0xfd4fffff 64bit pref]
[ 1.183776] pci_bus 0000:00: on NUMA node 0
[ 1.184097] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184169] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184239] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184311] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184380] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184448] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184516] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0
[ 1.184584] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0
[ 1.185292] vgaarb: setting as boot device: PCI:0000:01:00.0
[ 1.185294] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.185298] vgaarb: loaded
[ 1.185299] vgaarb: bridge control possible 0000:01:00.0
[ 1.185380] SCSI subsystem initialized
[ 1.185434] libata version 3.00 loaded.
[ 1.185439] ACPI: bus type USB registered
[ 1.185457] usbcore: registered new interface driver usbfs
[ 1.185467] usbcore: registered new interface driver hub
[ 1.185492] usbcore: registered new device driver usb
[ 1.185579] PCI: Using ACPI for IRQ routing
[ 1.191594] PCI: pci_cache_line_size set to 64 bytes
[ 1.191652] e820: reserve RAM buffer [mem 0x00098000-0x0009ffff]
[ 1.191654] e820: reserve RAM buffer [mem 0xcfda0000-0xcfffffff]
[ 1.191655] e820: reserve RAM buffer [mem 0x62f000000-0x62fffffff]
[ 1.191763] NetLabel: Initializing
[ 1.191764] NetLabel: domain hash size = 128
[ 1.191765] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.191775] NetLabel: unlabeled traffic allowed by default
[ 1.191808] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 1.191810] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 1.193868] Switched to clocksource hpet
[ 1.200824] AppArmor: AppArmor Filesystem Enabled
[ 1.200867] pnp: PnP ACPI init
[ 1.200961] system 00:00: [io 0x04d0-0x04d1] has been reserved
[ 1.200964] system 00:00: [io 0x0220-0x0225] has been reserved
[ 1.200965] system 00:00: [io 0x0290-0x0294] has been reserved
[ 1.200968] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.201311] pnp 00:01: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
[ 1.201315] pnp 00:01: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref]
[ 1.201319] pnp 00:01: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:06:06.0 BAR 6 [mem 0x00000000-0x0000ffff pref]
[ 1.201344] system 00:01: [io 0x0900-0x091f] has been reserved
[ 1.201346] system 00:01: [io 0x0228-0x022f] has been reserved
[ 1.201347] system 00:01: [io 0x040b] has been reserved
[ 1.201349] system 00:01: [io 0x04d6] has been reserved
[ 1.201351] system 00:01: [io 0x0c00-0x0c01] has been reserved
[ 1.201352] system 00:01: [io 0x0c14] has been reserved
[ 1.201354] system 00:01: [io 0x0c50-0x0c52] has been reserved
[ 1.201355] system 00:01: [io 0x0c6c-0x0c6d] has been reserved
[ 1.201357] system 00:01: [io 0x0c6f] has been reserved
[ 1.201358] system 00:01: [io 0x0cd0-0x0cd1] has been reserved
[ 1.201360] system 00:01: [io 0x0cd2-0x0cd3] has been reserved
[ 1.201361] system 00:01: [io 0x0cd4-0x0cdf] has been reserved
[ 1.201363] system 00:01: [io 0x0800-0x08fe] could not be reserved
[ 1.201364] system 00:01: [io 0x0a10-0x0a17] has been reserved
[ 1.201366] system 00:01: [io 0x0b00-0x0b0f] has been reserved
[ 1.201367] system 00:01: [io 0x0b10-0x0b1f] has been reserved
[ 1.201369] system 00:01: [io 0x0b20-0x0b3f] has been reserved
[ 1.201371] system 00:01: [mem 0xfee00400-0xfee00fff window] has been reserved
[ 1.201373] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.201579] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.202009] pnp 00:03: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.202124] system 00:04: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.202126] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.202417] system 00:05: [mem 0x000d9000-0x000dbfff] has been reserved
[ 1.202419] system 00:05: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 1.202421] system 00:05: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 1.202422] system 00:05: [mem 0x000fc000-0x000fffff] could not be reserved
[ 1.202424] system 00:05: [mem 0xcfda0000-0xcfdfffff] could not be reserved
[ 1.202426] system 00:05: [mem 0xffff0000-0xffffffff] has been reserved
[ 1.202427] system 00:05: [mem 0x00000000-0x0009ffff] could not be reserved
[ 1.202429] system 00:05: [mem 0x00100000-0xcfd9ffff] could not be reserved
[ 1.202430] system 00:05: [mem 0xcfe00000-0xcfefffff] has been reserved
[ 1.202432] system 00:05: [mem 0xcff00000-0xcfffffff] could not be reserved
[ 1.202433] system 00:05: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 1.202435] system 00:05: [mem 0xfee00000-0xfee00fff] could not be reserved
[ 1.202437] system 00:05: [mem 0xfff80000-0xfffeffff] has been reserved
[ 1.202439] system 00:05: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 1.202462] pnp: PnP ACPI: found 6 devices
[ 1.209005] clocksource acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 1.209033] pci 0000:01:00.0: BAR 6: assigned [mem 0xfde00000-0xfde1ffff pref]
[ 1.209035] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 1.209037] pci 0000:00:02.0: bridge window [io 0xe000-0xefff]
[ 1.209039] pci 0000:00:02.0: bridge window [mem 0xfde00000-0xfdefffff]
[ 1.209042] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[ 1.209044] pci 0000:00:04.0: PCI bridge to [bus 02]
[ 1.209046] pci 0000:00:04.0: bridge window [io 0xd000-0xdfff]
[ 1.209048] pci 0000:00:04.0: bridge window [mem 0xfdd00000-0xfddfffff]
[ 1.209050] pci 0000:00:04.0: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref]
[ 1.209053] pci 0000:03:00.0: BAR 6: assigned [mem 0xfdb00000-0xfdb0ffff pref]
[ 1.209055] pci 0000:00:05.0: PCI bridge to [bus 03]
[ 1.209056] pci 0000:00:05.0: bridge window [io 0xc000-0xcfff]
[ 1.209059] pci 0000:00:05.0: bridge window [mem 0xfdb00000-0xfdbfffff]
[ 1.209061] pci 0000:00:05.0: bridge window [mem 0xfda00000-0xfdafffff 64bit pref]
[ 1.209063] pci 0000:00:09.0: PCI bridge to [bus 04]
[ 1.209065] pci 0000:00:09.0: bridge window [io 0xb000-0xbfff]
[ 1.209067] pci 0000:00:09.0: bridge window [mem 0xfd900000-0xfd9fffff]
[ 1.209069] pci 0000:00:09.0: bridge window [mem 0xfd600000-0xfd6fffff 64bit pref]
[ 1.209072] pci 0000:00:0a.0: PCI bridge to [bus 05]
[ 1.209073] pci 0000:00:0a.0: bridge window [io 0xa000-0xafff]
[ 1.209075] pci 0000:00:0a.0: bridge window [mem 0xfd300000-0xfd3fffff]
[ 1.209077] pci 0000:00:0a.0: bridge window [mem 0xfd200000-0xfd2fffff 64bit pref]
[ 1.209081] pci 0000:06:06.0: BAR 6: assigned [mem 0xfd700000-0xfd70ffff pref]
[ 1.209082] pci 0000:00:14.4: PCI bridge to [bus 06]
[ 1.209084] pci 0000:00:14.4: bridge window [io 0x9000-0x9fff]
[ 1.209088] pci 0000:00:14.4: bridge window [mem 0xfd800000-0xfd8fffff]
[ 1.209090] pci 0000:00:14.4: bridge window [mem 0xfd700000-0xfd7fffff pref]
[ 1.209095] pci 0000:00:15.0: PCI bridge to [bus 07]
[ 1.209096] pci 0000:00:15.0: bridge window [io 0x8000-0x8fff]
[ 1.209099] pci 0000:00:15.0: bridge window [mem 0xfd500000-0xfd5fffff]
[ 1.209102] pci 0000:00:15.0: bridge window [mem 0xfd400000-0xfd4fffff 64bit pref]
[ 1.209106] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 1.209108] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 1.209109] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 1.209111] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff window]
[ 1.209112] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff window]
[ 1.209113] pci_bus 0000:00: resource 9 [mem 0xd0000000-0xfebfffff window]
[ 1.209115] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 1.209116] pci_bus 0000:01: resource 1 [mem 0xfde00000-0xfdefffff]
[ 1.209117] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[ 1.209119] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 1.209120] pci_bus 0000:02: resource 1 [mem 0xfdd00000-0xfddfffff]
[ 1.209122] pci_bus 0000:02: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref]
[ 1.209123] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
[ 1.209124] pci_bus 0000:03: resource 1 [mem 0xfdb00000-0xfdbfffff]
[ 1.209126] pci_bus 0000:03: resource 2 [mem 0xfda00000-0xfdafffff 64bit pref]
[ 1.209127] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff]
[ 1.209128] pci_bus 0000:04: resource 1 [mem 0xfd900000-0xfd9fffff]
[ 1.209130] pci_bus 0000:04: resource 2 [mem 0xfd600000-0xfd6fffff 64bit pref]
[ 1.209131] pci_bus 0000:05: resource 0 [io 0xa000-0xafff]
[ 1.209132] pci_bus 0000:05: resource 1 [mem 0xfd300000-0xfd3fffff]
[ 1.209134] pci_bus 0000:05: resource 2 [mem 0xfd200000-0xfd2fffff 64bit pref]
[ 1.209135] pci_bus 0000:06: resource 0 [io 0x9000-0x9fff]
[ 1.209136] pci_bus 0000:06: resource 1 [mem 0xfd800000-0xfd8fffff]
[ 1.209138] pci_bus 0000:06: resource 2 [mem 0xfd700000-0xfd7fffff pref]
[ 1.209139] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7 window]
[ 1.209141] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff window]
[ 1.209142] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff window]
[ 1.209143] pci_bus 0000:06: resource 7 [mem 0x000c0000-0x000dffff window]
[ 1.209145] pci_bus 0000:06: resource 8 [mem 0xfed40000-0xfed44fff window]
[ 1.209146] pci_bus 0000:06: resource 9 [mem 0xd0000000-0xfebfffff window]
[ 1.209147] pci_bus 0000:07: resource 0 [io 0x8000-0x8fff]
[ 1.209149] pci_bus 0000:07: resource 1 [mem 0xfd500000-0xfd5fffff]
[ 1.209150] pci_bus 0000:07: resource 2 [mem 0xfd400000-0xfd4fffff 64bit pref]
[ 1.209223] NET: Registered protocol family 2
[ 1.209508] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[ 1.209975] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.210185] TCP: Hash tables configured (established 262144 bind 65536)
[ 1.210250] UDP hash table entries: 16384 (order: 7, 524288 bytes)
[ 1.210393] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes)
[ 1.210569] NET: Registered protocol family 1
[ 1.469060] pci 0000:01:00.0: Video device with shadowed ROM
[ 1.469477] pci 0000:06:06.0: Firmware left e100 interrupts enabled; disabling
[ 1.469483] PCI: CLS 64 bytes, default 64
[ 1.469539] Unpacking initramfs...
[ 1.599287] Freeing initrd memory: 11016K (ffff880036a6c000 - ffff88003752e000)
[ 1.599669] pci 0000:00:00.2: can't derive routing for PCI INT A
[ 1.599670] pci 0000:00:00.2: PCI INT A: no GSI
[ 1.600048] AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
[ 1.600049] AMD-Vi: Interrupt remapping enabled
[ 1.610639] AMD-Vi: Lazy IO/TLB flushing enabled
[ 1.682895] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.682897] software IO TLB [mem 0xcbda0000-0xcfda0000] (64MB) mapped at [ffff8800cbda0000-ffff8800cfd9ffff]
[ 1.682949] perf: AMD NB counters detected
[ 1.683057] microcode: CPU0: patch_level=0x0600081c
[ 1.683065] microcode: CPU1: patch_level=0x0600081c
[ 1.683072] microcode: CPU2: patch_level=0x0600081c
[ 1.683080] microcode: CPU3: patch_level=0x0600081c
[ 1.683086] microcode: CPU4: patch_level=0x0600081c
[ 1.683090] microcode: CPU5: patch_level=0x0600081c
[ 1.683097] microcode: CPU6: patch_level=0x0600081c
[ 1.683103] microcode: CPU7: patch_level=0x0600081c
[ 1.683156] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[ 1.683160] LVT offset 0 assigned for vector 0x400
[ 1.683177] perf: AMD IBS detected (0x000000ff)
[ 1.683199] Scanning for low memory corruption every 60 seconds
[ 1.683545] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 1.683592] audit: initializing netlink subsys (disabled)
[ 1.683608] audit: type=2000 audit(1437494892.691:1): initialized
[ 1.683878] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.683908] zpool: loaded
[ 1.683910] zbud: loaded
[ 1.684011] VFS: Disk quotas dquot_6.6.0
[ 1.684034] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.684277] Key type big_key registered
[ 1.684593] Key type asymmetric registered
[ 1.684596] Asymmetric key parser 'x509' registered
[ 1.684616] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.684662] io scheduler noop registered
[ 1.684664] io scheduler deadline registered
[ 1.684680] io scheduler cfq registered (default)
[ 1.685441] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.685458] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.685478] vesafb: mode is 1600x1200x32, linelength=6400, pages=0
[ 1.685479] vesafb: scrolling: redraw
[ 1.685481] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[ 1.685500] vesafb: framebuffer at 0xd0000000, mapped to 0xffffc90003800000, using 7552k, total 7552k
[ 1.724028] Console: switching to colour frame buffer device 200x75
[ 1.762458] fb0: VESA VGA frame buffer device
[ 1.762494] GHES: HEST is not enabled!
[ 1.762540] Serial: 8250/16550 driver, 32 ports, IRQ sharing disabled
[ 1.783013] 00:03: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 1.784537] Non-volatile memory driver v1.3
[ 1.784567] Linux agpgart interface v0.103
[ 1.785280] ahci 0000:00:11.0: version 3.0
[ 1.785500] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 6 Gbps 0x3f impl SATA mode
[ 1.785502] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 1.786287] scsi host0: ahci
[ 1.786382] scsi host1: ahci
[ 1.786474] scsi host2: ahci
[ 1.786565] scsi host3: ahci
[ 1.786655] scsi host4: ahci
[ 1.786746] scsi host5: ahci
[ 1.786788] ata1: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff100 irq 19
[ 1.786790] ata2: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff180 irq 19
[ 1.786791] ata3: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff200 irq 19
[ 1.786793] ata4: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff280 irq 19
[ 1.786795] ata5: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff300 irq 19
[ 1.786797] ata6: SATA max UDMA/133 abar m1024@0xfdfff000 port 0xfdfff380 irq 19
[ 1.786832] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.786837] ehci-pci: EHCI PCI platform driver
[ 1.786987] QUIRK: Enable AMD PLL fix
[ 1.787003] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 1.787008] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 1.787012] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.787021] ehci-pci 0000:00:12.2: debug port 1
[ 1.787056] ehci-pci 0000:00:12.2: irq 17, io mem 0xfdffd000
[ 1.792233] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.792281] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.792283] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.792284] usb usb1: Product: EHCI Host Controller
[ 1.792285] usb usb1: Manufacturer: Linux 4.1.2-1.1-desktop ehci_hcd
[ 1.792287] usb usb1: SerialNumber: 0000:00:12.2
[ 1.792406] hub 1-0:1.0: USB hub found
[ 1.792412] hub 1-0:1.0: 5 ports detected
[ 1.792694] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 1.792698] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 1.792701] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.792708] ehci-pci 0000:00:13.2: debug port 1
[ 1.792729] ehci-pci 0000:00:13.2: irq 17, io mem 0xfdffb000
[ 1.798221] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.798252] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.798254] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.798255] usb usb2: Product: EHCI Host Controller
[ 1.798256] usb usb2: Manufacturer: Linux 4.1.2-1.1-desktop ehci_hcd
[ 1.798257] usb usb2: SerialNumber: 0000:00:13.2
[ 1.798369] hub 2-0:1.0: USB hub found
[ 1.798373] hub 2-0:1.0: 5 ports detected
[ 1.798654] ehci-pci 0000:00:16.2: EHCI Host Controller
[ 1.798658] ehci-pci 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 1.798661] ehci-pci 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.798668] ehci-pci 0000:00:16.2: debug port 1
[ 1.798689] ehci-pci 0000:00:16.2: irq 17, io mem 0xfdff8000
[ 1.804214] ehci-pci 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 1.804259] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.804261] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.804262] usb usb3: Product: EHCI Host Controller
[ 1.804263] usb usb3: Manufacturer: Linux 4.1.2-1.1-desktop ehci_hcd
[ 1.804264] usb usb3: SerialNumber: 0000:00:16.2
[ 1.804374] hub 3-0:1.0: USB hub found
[ 1.804378] hub 3-0:1.0: 4 ports detected
[ 1.804491] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.804495] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.804537] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 1.837134] i8042: Failed to disable AUX port, but continuing anyway... Is this a SiS?
[ 1.837139] i8042: If AUX port is really absent please use the 'i8042.noaux' option
[ 2.086970] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.087084] mousedev: PS/2 mouse device common for all mice
[ 2.087190] rtc_cmos 00:02: RTC can wake from S4
[ 2.087293] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 2.087315] rtc_cmos 00:02: alarms up to one month, 242 bytes nvram, hpet irqs
[ 2.087321] rtc_cmos: BIOS has alarm-disable quirk - RTC alarms disabled
[ 2.087330] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.087348] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.087455] usbcore: registered new interface driver usbhid
[ 2.087456] usbhid: USB HID core driver
[ 2.087548] NET: Registered protocol family 10
[ 2.088405] registered taskstats version 1
[ 2.090888] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.090911] ata6: SATA link down (SStatus 0 SControl 300)
[ 2.091395] Key type encrypted registered
[ 2.091400] AppArmor: AppArmor sha1 policy hashing enabled
[ 2.091701] Magic number: 7:346:136
[ 2.091712] misc autofs: hash matches
[ 2.091840] rtc_cmos 00:02: setting system clock to 2015-07-21 16:08:14 UTC (1437494894)
[ 2.091898] PM: Checking hibernation image partition /dev/raid0/swap
[ 2.093890] usb 1-4: new high-speed USB device number 2 using ehci-pci
[ 2.245705] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.245724] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.245742] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.245760] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.246477] ata2.00: ATA-8: ST3000DM001-1CH166, CC24, max UDMA/133
[ 2.246479] ata2.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 2.246893] ata3.00: ATA-9: ST3000DM001-1CH166, CC29, max UDMA/133
[ 2.246894] ata3.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[ 2.247314] ata2.00: configured for UDMA/133
[ 2.247776] ata3.00: configured for UDMA/133
[ 2.253824] ata5.00: ATAPI: HL-DT-ST BD-RE BH10LS38, 1.00, max UDMA/133
[ 2.257634] ata1.00: ATA-8: Corsair Force GT, 1.3.3, max UDMA/133
[ 2.257636] ata1.00: 468862128 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.257796] ata5.00: configured for UDMA/133
[ 2.267524] ata1.00: configured for UDMA/133
[ 2.267655] scsi 0:0:0:0: Direct-Access ATA Corsair Force GT 3 PQ: 0 ANSI: 5
[ 2.267846] sd 0:0:0:0: [sda] 468862128 512-byte logical blocks: (240 GB/223 GiB)
[ 2.267940] scsi 1:0:0:0: Direct-Access ATA ST3000DM001-1CH1 CC24 PQ: 0 ANSI: 5
[ 2.267945] sd 0:0:0:0: [sda] Write Protect is off
[ 2.267948] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.267977] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.268139] sd 1:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 2.268140] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[ 2.268219] sd 1:0:0:0: [sdb] Write Protect is off
[ 2.268221] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 2.268235] scsi 2:0:0:0: Direct-Access ATA ST3000DM001-1CH1 CC29 PQ: 0 ANSI: 5
[ 2.268248] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.268383] sda: sda1 sda2
[ 2.268403] sd 2:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[ 2.268405] sd 2:0:0:0: [sdc] 4096-byte physical blocks
[ 2.268470] sd 2:0:0:0: [sdc] Write Protect is off
[ 2.268473] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 2.268502] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.268708] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.277068] scsi 4:0:0:0: CD-ROM HL-DT-ST BD-RE BH10LS38 1.00 PQ: 0 ANSI: 5
[ 2.303747] sdb: sdb1 sdb2
[ 2.304011] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 2.309718] sdc: sdc1 sdc2
[ 2.309964] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 2.309973] PM: Hibernation image not present or could not be loaded.
[ 2.310383] Freeing unused kernel memory: 1564K (ffffffff81f1a000 - ffffffff820a1000)
[ 2.310384] Write protecting the kernel read-only data: 14336k
[ 2.310880] Freeing unused kernel memory: 1360K (ffff8800016ac000 - ffff880001800000)
[ 2.311199] Freeing unused kernel memory: 1148K (ffff880001ce1000 - ffff880001e00000)
[ 2.335902] AVX version of gcm_enc/dec engaged.
[ 2.335904] AES CTR mode by8 optimization enabled
[ 2.340199] device-mapper: uevent: version 1.0.3
[ 2.340260] device-mapper: ioctl: 4.31.0-ioctl (2015-3-12) initialised: dm-devel@xxxxxxxxxx
[ 2.347216] md: raid0 personality registered for level 0
[ 2.348333] md: raid1 personality registered for level 1
[ 2.349470] md: raid10 personality registered for level 10
[ 2.366562] raid6: sse2x1 gen() 7250 MB/s
[ 2.383533] raid6: sse2x1 xor() 5494 MB/s
[ 2.400512] raid6: sse2x2 gen() 11695 MB/s
[ 2.417501] raid6: sse2x2 xor() 7902 MB/s
[ 2.434469] raid6: sse2x4 gen() 13546 MB/s
[ 2.451457] raid6: sse2x4 xor() 6962 MB/s
[ 2.451458] raid6: using algorithm sse2x4 gen() 13546 MB/s
[ 2.451459] raid6: .... xor() 6962 MB/s, rmw enabled
[ 2.451460] raid6: using ssse3x2 recovery algorithm
[ 2.451635] async_tx: api initialized (async)
[ 2.451910] xor: automatically using best checksumming function:
[ 2.461444] avx : 4480.000 MB/sec
[ 2.462438] md: raid6 personality registered for level 6
[ 2.462439] md: raid5 personality registered for level 5
[ 2.462440] md: raid4 personality registered for level 4
[ 2.466477] hp_sw: device handler registered
[ 2.467494] rdac: device handler registered
[ 2.468522] alua: device handler registered
[ 2.469512] emc: device handler registered
[ 2.472323] systemd-udevd[233]: starting version 208
[ 2.480619] ACPI: acpi_idle registered with cpuidle
[ 2.490732] ohci-pci: OHCI PCI platform driver
[ 2.490939] ohci-pci 0000:00:12.0: OHCI PCI host controller
[ 2.490945] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 2.490981] ohci-pci 0000:00:12.0: irq 18, io mem 0xfdffe000
[ 2.545409] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.545412] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.545414] usb usb4: Product: OHCI PCI host controller
[ 2.545415] usb usb4: Manufacturer: Linux 4.1.2-1.1-desktop ohci_hcd
[ 2.545416] usb usb4: SerialNumber: 0000:00:12.0
[ 2.545642] hub 4-0:1.0: USB hub found
[ 2.545652] hub 4-0:1.0: 5 ports detected
[ 2.545959] ohci-pci 0000:00:13.0: OHCI PCI host controller
[ 2.545964] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 2.545983] ohci-pci 0000:00:13.0: irq 18, io mem 0xfdffc000
[ 2.600358] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.600361] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.600362] usb usb5: Product: OHCI PCI host controller
[ 2.600364] usb usb5: Manufacturer: Linux 4.1.2-1.1-desktop ohci_hcd
[ 2.600365] usb usb5: SerialNumber: 0000:00:13.0
[ 2.600501] hub 5-0:1.0: USB hub found
[ 2.600511] hub 5-0:1.0: 5 ports detected
[ 2.600800] ohci-pci 0000:00:14.5: OHCI PCI host controller
[ 2.600804] ohci-pci 0000:00:14.5: new USB bus registered, assigned bus number 6
[ 2.600822] ohci-pci 0000:00:14.5: irq 18, io mem 0xfdffa000
[ 2.607070] md: bind<sdc2>
[ 2.639955] md: bind<sdb2>
[ 2.642054] md/raid1:md0: active with 2 out of 2 mirrors
[ 2.642163] created bitmap (22 pages) for device md0
[ 2.642611] md0: bitmap initialized from disk: read 2 pages, set 0 of 44710 bits
[ 2.655363] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.655366] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.655367] usb usb6: Product: OHCI PCI host controller
[ 2.655369] usb usb6: Manufacturer: Linux 4.1.2-1.1-desktop ohci_hcd
[ 2.655370] usb usb6: SerialNumber: 0000:00:14.5
[ 2.655555] hub 6-0:1.0: USB hub found
[ 2.655563] hub 6-0:1.0: 2 ports detected
[ 2.655808] ohci-pci 0000:00:16.0: OHCI PCI host controller
[ 2.655813] ohci-pci 0000:00:16.0: new USB bus registered, assigned bus number 7
[ 2.655830] ohci-pci 0000:00:16.0: irq 18, io mem 0xfdff9000
[ 2.683270] tsc: Refined TSC clocksource calibration: 4026.928 MHz
[ 2.683277] clocksource tsc: mask: 0xffffffffffffffff max_cycles: 0x3a0bba24476, max_idle_ns: 440795259958 ns
[ 2.686227] md0: detected capacity change from 0 to 3000382058496
[ 2.692059] random: nonblocking pool is initialized
[ 2.710285] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.710287] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.710289] usb usb7: Product: OHCI PCI host controller
[ 2.710290] usb usb7: Manufacturer: Linux 4.1.2-1.1-desktop ohci_hcd
[ 2.710292] usb usb7: SerialNumber: 0000:00:16.0
[ 2.710416] hub 7-0:1.0: USB hub found
[ 2.710424] hub 7-0:1.0: 4 ports detected
[ 2.785728] usb 1-4: New USB device found, idVendor=0bda, idProduct=0151
[ 2.785730] usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.785732] usb 1-4: Product: USB2.0-CRW
[ 2.785733] usb 1-4: Manufacturer: Generic
[ 2.785734] usb 1-4: SerialNumber: 20060413092100000
[ 2.804182] md: linear personality registered for level -1
[ 3.032899] usb 7-3: new low-speed USB device number 2 using ohci-pci
[ 3.185789] usb 7-3: New USB device found, idVendor=046a, idProduct=0001
[ 3.185796] usb 7-3: New USB device strings: Mfr=1, Product=0, SerialNumber=0
[ 3.185801] usb 7-3: Manufacturer: Cherry GmbH
[ 3.195203] input: Cherry GmbH as /devices/pci0000:00/0000:00:16.0/usb7/7-3/7-3:1.0/0003:046A:0001.0001/input/input1
[ 3.245925] hid-generic 0003:046A:0001.0001: input,hidraw0: USB HID v1.11 Keyboard [Cherry GmbH] on usb-0000:00:16.0-3/input0
[ 3.682381] Switched to clocksource tsc
[ 13.476204] PM: Marking nosave pages: [mem 0x00000000-0x00000fff]
[ 13.476207] PM: Marking nosave pages: [mem 0x00098000-0x000fffff]
[ 13.476210] PM: Marking nosave pages: [mem 0xcfda0000-0xffffffff]
[ 13.476524] PM: Marking nosave pages: [mem 0xc4000000-0xc7ffffff]
[ 13.476771] PM: Basic memory bitmaps created
[ 13.477447] PM: Basic memory bitmaps freed
[ 13.539965] PM: Starting manual resume from disk
[ 13.539968] PM: Hibernation image partition 254:21 present
[ 13.539969] PM: Looking for hibernation image.
[ 13.540340] PM: Image not found (code -22)
[ 13.540341] PM: Hibernation image not present or could not be loaded.
[ 13.562069] EXT4-fs (dm-9): mounted filesystem with ordered data mode. Opts: (null)
[ 13.663282] systemd[1]: systemd 208 running in system mode. (+PAM +LIBWRAP +AUDIT +SELINUX -IMA +SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 13.663713] systemd[1]: Set hostname to <dualc>.
[ 13.678916] LVM: Logical Volume autoactivation enabled.
[ 13.678934] LVM: Activation generator successfully completed.
[ 13.703781] systemd[1]: [/etc/systemd/system/proxy.service:19] Unknown lvalue 'Requires' in section 'Service'
[ 13.732378] systemd[1]: Starting Replay Read-Ahead Data...
[ 13.732958] systemd[1]: Starting Collect Read-Ahead Data...
[ 13.733247] systemd[1]: Starting System Time Synchronized.
[ 13.733257] systemd[1]: Reached target System Time Synchronized.
[ 13.733273] systemd[1]: Starting Syslog Socket.
[ 13.733303] systemd[1]: Listening on Syslog Socket.
[ 13.733317] systemd[1]: Starting Remote File Systems (Pre).
[ 13.733330] systemd[1]: Reached target Remote File Systems (Pre).
[ 13.733338] systemd[1]: Starting Remote File Systems.
[ 13.733344] systemd[1]: Reached target Remote File Systems.
[ 13.733365] systemd[1]: Starting Delayed Shutdown Socket.
[ 13.733380] systemd[1]: Listening on Delayed Shutdown Socket.
[ 13.733401] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 13.733416] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 13.733422] systemd[1]: Starting LVM2 metadata daemon socket.
[ 13.733443] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 13.733458] systemd[1]: Starting udev Kernel Socket.
[ 13.733476] systemd[1]: Listening on udev Kernel Socket.
[ 13.733485] systemd[1]: Starting udev Control Socket.
[ 13.733499] systemd[1]: Listening on udev Control Socket.
[ 13.733510] systemd[1]: Expecting device dev-disk-by\x2did-ata\x2dCorsair_Force_GT_1203820100000989041B\x2dpart2.device...
[ 13.733516] systemd[1]: Expecting device dev-mapper-cr_ata\x2dCorsair_Force_GT_1203820100000989041B\x2dpart2.device...
[ 13.733526] systemd[1]: Expecting device dev-md0.device...
[ 13.733533] systemd[1]: Expecting device dev-mapper-cr_md0.device...
[ 13.733543] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 13.733573] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 13.733582] systemd[1]: Starting Paths.
[ 13.733589] systemd[1]: Reached target Paths.
[ 13.733599] systemd[1]: Starting Journal Socket.
[ 13.733631] systemd[1]: Listening on Journal Socket.
[ 13.733650] systemd[1]: Mounting Huge Pages File System...
[ 13.733957] systemd[1]: Mounting POSIX Message Queue File System...
[ 13.734270] systemd[1]: Starting Create dynamic rule for /dev/root link...
[ 13.734609] systemd[1]: Starting LSB: Set default boot entry if called...
[ 13.734898] systemd[1]: Starting Journal Service...
[ 13.735225] systemd[1]: Started Journal Service.
[ 13.756511] systemd-journald[671]: Vacuuming done, freed 0 bytes
[ 13.796200] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 13.796242] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 13.796301] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 13.796346] scsi 4:0:0:0: Attached scsi generic sg3 type 5
[ 13.811927] systemd-udevd[713]: starting version 208
[ 13.859631] acpi-cpufreq: overriding BIOS provided _PSD data
[ 13.860774] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 13.860949] ACPI: Power Button [PWRB]
[ 13.861207] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 13.861280] ACPI: Power Button [PWRF]
[ 13.862229] wmi: Mapper loaded
[ 13.876262] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 13.879195] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 13.879218] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 8
[ 13.879297] xhci_hcd 0000:02:00.0: hcc params 0x040050af hci version 0x100 quirks 0x00080490
[ 13.879662] usb usb8: New USB device found, idVendor=1d6b, idProduct=0002
[ 13.879666] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 13.879669] usb usb8: Product: xHCI Host Controller
[ 13.879672] usb usb8: Manufacturer: Linux 4.1.2-1.1-desktop xhci-hcd
[ 13.879674] usb usb8: SerialNumber: 0000:02:00.0
[ 13.880658] hub 8-0:1.0: USB hub found
[ 13.880671] hub 8-0:1.0: 2 ports detected
[ 13.881859] AMD IOMMUv2 driver by Joerg Roedel <jroedel@xxxxxxx>
[ 13.881861] AMD IOMMUv2 functionality not available on this system
[ 13.882751] xhci_hcd 0000:02:00.0: xHCI Host Controller
[ 13.882756] xhci_hcd 0000:02:00.0: new USB bus registered, assigned bus number 9
[ 13.882811] usb usb9: New USB device found, idVendor=1d6b, idProduct=0003
[ 13.882814] usb usb9: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 13.882816] usb usb9: Product: xHCI Host Controller
[ 13.882819] usb usb9: Manufacturer: Linux 4.1.2-1.1-desktop xhci-hcd
[ 13.882821] usb usb9: SerialNumber: 0000:02:00.0
[ 13.883058] hub 9-0:1.0: USB hub found
[ 13.883069] hub 9-0:1.0: 2 ports detected
[ 13.883396] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 13.883403] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 10
[ 13.883492] xhci_hcd 0000:05:00.0: hcc params 0x040050af hci version 0x100 quirks 0x00080490
[ 13.883591] usb usb10: New USB device found, idVendor=1d6b, idProduct=0002
[ 13.883594] usb usb10: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 13.883596] usb usb10: Product: xHCI Host Controller
[ 13.883597] usb usb10: Manufacturer: Linux 4.1.2-1.1-desktop xhci-hcd
[ 13.883599] usb usb10: SerialNumber: 0000:05:00.0
[ 13.883867] hub 10-0:1.0: USB hub found
[ 13.883877] hub 10-0:1.0: 2 ports detected
[ 13.883980] xhci_hcd 0000:05:00.0: xHCI Host Controller
[ 13.883983] xhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 11
[ 13.884021] usb usb11: New USB device found, idVendor=1d6b, idProduct=0003
[ 13.884023] usb usb11: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 13.884025] usb usb11: Product: xHCI Host Controller
[ 13.884026] usb usb11: Manufacturer: Linux 4.1.2-1.1-desktop xhci-hcd
[ 13.884028] usb usb11: SerialNumber: 0000:05:00.0
[ 13.884507] hub 11-0:1.0: USB hub found
[ 13.884520] hub 11-0:1.0: 2 ports detected
[ 13.900332] ACPI Warning: SystemIO range 0x0000000000000B00-0x0000000000000B07 conflicts with OpRegion 0x0000000000000B00-0x0000000000000B0F (\SOR1) (20150410/utaddress-254)
[ 13.900338] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 13.900659] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[ 13.900721] sp5100_tco: PCI Revision ID: 0x42
[ 13.900749] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address
[ 13.900759] sp5100_tco: Last reboot was not triggered by watchdog.
[ 13.900805] sp5100_tco: initialized (0xffffc90003150b00). heartbeat=60 sec (nowayout=0)
[ 13.901992] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 13.901994] e100: Copyright(c) 1999-2006 Intel Corporation
[ 13.906718] MCE: In-kernel MCE decoding enabled.
[ 13.908716] EDAC MC: Ver: 3.0.0
[ 13.909008] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 13.909910] AMD64 EDAC driver v3.4.0
[ 13.909936] EDAC amd64: DRAM ECC disabled.
[ 13.909944] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
(Note that use of the override may cause unknown side effects.)
[ 13.931402] e100 0000:06:06.0 eth0: addr 0xfd8ff000, irq 20, MAC addr 00:02:b3:8f:f9:11
[ 13.936759] usb-storage 1-4:1.0: USB Mass Storage device detected
[ 13.939401] scsi host6: usb-storage 1-4:1.0
[ 13.939544] usbcore: registered new interface driver usb-storage
[ 13.940828] kvm: Nested Virtualization enabled
[ 13.940832] kvm: Nested Paging enabled
[ 13.957415] snd_hda_intel 0000:01:00.1: Handle VGA-switcheroo audio client
[ 13.965755] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:02.0/0000:01:00.1/sound/card1/input5
[ 13.967576] sr 4:0:0:0: [sr0] scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 13.967581] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 13.967746] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 13.970666] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC889: line_outs=4 (0x14/0x15/0x16/0x17/0x0) type:line
[ 13.970670] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 13.970672] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
[ 13.970674] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 13.970676] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x1e
[ 13.970677] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 13.970680] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19
[ 13.970681] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18
[ 13.970683] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a
[ 13.984404] firewire_ohci 0000:06:0e.0: added OHCI v1.10 device as card 0, 4 IR + 8 IT contexts, quirks 0x11
[ 13.989250] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input6
[ 13.989358] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
[ 13.989453] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
[ 13.989545] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
[ 13.989637] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
[ 13.989732] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
[ 13.989821] input: HDA ATI SB Line Out Side as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
[ 13.989913] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
[ 14.036347] <6>[fglrx] Maximum main memory to use for locked dma buffers: 23513 MBytes.
[ 14.036807] <6>[fglrx] vendor: 1002 device: 6759 revision: 0 count: 1
[ 14.037328] <6>[fglrx] IOMMU is enabled, CrossFire are not supported on this platform
[ 14.037332] <6>[fglrx] Disable IOMMU in BIOS options or kernel boot parameters to support CF
[ 14.037918] <6>[fglrx] ioport: bar 4, base 0xee00, size: 0x100
[ 14.038641] <6>[fglrx] Kernel PAT support is enabled
[ 14.038664] <6>[fglrx] module loaded - fglrx 15.20.3 [Jun 22 2015] with 1 minors
[ 14.056720] EXT4-fs (dm-10): mounted filesystem with ordered data mode. Opts: acl,user_xattr
[ 14.116940] EXT4-fs (dm-2): mounted filesystem without journal. Opts: acl,user_xattr
[ 14.118115] EXT4-fs (dm-11): mounted filesystem with ordered data mode. Opts: acl,user_xattr
[ 14.145952] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: acl,user_xattr
[ 14.183189] usb 8-1: new low-speed USB device number 2 using xhci_hcd
[ 14.329462] usb 8-1: New USB device found, idVendor=046d, idProduct=c03e
[ 14.329469] usb 8-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 14.329473] usb 8-1: Product: USB-PS/2 Optical Mouse
[ 14.329477] usb 8-1: Manufacturer: Logitech
[ 14.329646] usb 8-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
[ 14.342873] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:04.0/0000:02:00.0/usb8/8-1/8-1:1.0/0003:046D:C03E.0002/input/input14
[ 14.343056] hid-generic 0003:046D:C03E.0002: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:02:00.0-1/input0
[ 14.407313] EXT4-fs (dm-3): mounted filesystem without journal. Opts: acl,user_xattr
[ 14.484227] EXT4-fs (dm-4): mounted filesystem without journal. Opts: acl,user_xattr
[ 14.484962] firewire_core 0000:06:0e.0: created device fw0: GUID 0049e55043900400, S400
[ 14.552339] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 14.553852] XFS (dm-5): Mounting V4 Filesystem
[ 14.608070] XFS (dm-5): Ending clean mount
[ 14.655754] EXT4-fs (dm-6): mounted filesystem without journal. Opts: acl,user_xattr
[ 14.684307] EXT4-fs (dm-7): mounted filesystem without journal. Opts: acl,user_xattr
[ 14.747561] EXT4-fs (dm-8): mounted filesystem without journal. Opts: acl,user_xattr
[ 14.907465] Adding 8388604k swap on /dev/mapper/raid0-swap. Priority:-1 extents:1 across:8388604k FS
[ 14.910351] XFS (dm-22): Mounting V4 Filesystem
[ 14.945668] scsi 6:0:0:0: Direct-Access Generic- Compact Flash 1.00 PQ: 0 ANSI: 0 CCS
[ 14.945916] sd 6:0:0:0: Attached scsi generic sg4 type 0
[ 14.952909] scsi 6:0:0:1: Direct-Access Generic- SM/xD-Picture 1.00 PQ: 0 ANSI: 0 CCS
[ 14.953034] sd 6:0:0:1: Attached scsi generic sg5 type 0
[ 14.960656] scsi 6:0:0:2: Direct-Access Generic- SD/MMC 1.00 PQ: 0 ANSI: 0 CCS
[ 14.960788] sd 6:0:0:2: Attached scsi generic sg6 type 0
[ 14.969140] scsi 6:0:0:3: Direct-Access Generic- MS/MS-Pro 1.00 PQ: 0 ANSI: 0 CCS
[ 14.969691] sd 6:0:0:3: Attached scsi generic sg7 type 0
[ 14.978273] sd 6:0:0:0: [sdd] Attached SCSI removable disk
[ 14.988864] sd 6:0:0:1: [sde] Attached SCSI removable disk
[ 14.998469] sd 6:0:0:2: [sdf] Attached SCSI removable disk
[ 15.008088] sd 6:0:0:3: [sdg] Attached SCSI removable disk
[ 15.195068] XFS (dm-28): Mounting V4 Filesystem
[ 15.596355] XFS (dm-13): Mounting V4 Filesystem
[ 15.629840] EXT4-fs (dm-20): mounted filesystem with ordered data mode. Opts: acl,user_xattr
[ 15.642956] XFS (dm-15): Mounting V4 Filesystem
[ 15.753325] XFS (dm-14): Mounting V4 Filesystem
[ 15.989882] XFS (dm-22): Ending clean mount
[ 16.138038] AMD-Vi: Event logged [IO_PAGE_FAULT device=00:11.0 domain=0x0008 address=0x4027971700618000 flags=0x0010]
[ 16.138378] AMD-Vi: Event logged [IO_PAGE_FAULT device=00:11.0 domain=0x0008 address=0x4027971700618040 flags=0x0010]
[ 16.138708] AMD-Vi: Event logged [IO_PAGE_FAULT device=00:11.0 domain=0x0008 address=0x4027971700618080 flags=0x0010]
[ 16.157439] XFS (dm-28): Ending clean mount
[ 16.877253] floppy0: no floppy controllers found
[ 46.677498] ata3.00: exception Emask 0x0 SAct 0x1e0000 SErr 0x0 action 0x6 frozen
[ 46.677738] ata3.00: failed command: WRITE FPDMA QUEUED
[ 46.677906] ata3.00: cmd 61/00:88:17:8f:27/08:00:14:00:00/40 tag 17 ncq 1048576 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 46.678408] ata3.00: status: { DRDY }
[ 46.678522] ata3.00: failed command: WRITE FPDMA QUEUED
[ 46.678688] ata3.00: cmd 61/00:90:17:97:27/08:00:14:00:00/40 tag 18 ncq 1048576 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 46.679147] ata3.00: status: { DRDY }
[ 46.679260] ata3.00: failed command: WRITE FPDMA QUEUED
[ 46.679448] ata3.00: cmd 61/30:98:24:9a:26/07:00:8c:00:00/40 tag 19 ncq 942080 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 46.691879] ata3.00: status: { DRDY }
[ 46.703885] ata3.00: failed command: WRITE FPDMA QUEUED
[ 46.715701] ata3.00: cmd 61/e0:a0:54:a1:26/06:00:8c:00:00/40 tag 20 ncq 901120 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 46.739165] ata3.00: status: { DRDY }
[ 46.750696] ata3: hard resetting link
[ 47.260764] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 47.262572] ata3.00: configured for UDMA/133
[ 47.262600] ata3.00: device reported invalid CHS sector 0
[ 47.262659] ata3.00: device reported invalid CHS sector 0
[ 47.262670] ata3.00: device reported invalid CHS sector 0
[ 47.262689] ata3.00: device reported invalid CHS sector 0
[ 47.262724] ata3: EH complete
[ 47.271755] XFS (dm-13): Ending clean mount
[ 47.542578] XFS (dm-15): Ending clean mount
[ 47.573983] XFS (dm-14): Ending clean mount
[ 47.581867] systemd-journald[671]: Received request to flush runtime journal from PID 1
[ 47.624412] audit: type=1400 audit(1437494940.083:2): apparmor="STATUS" operation="profile_load" name="/{usr/,}bin/ping" pid=1199 comm="apparmor_parser"
[ 47.640195] audit: type=1400 audit(1437494940.099:3): apparmor="STATUS" operation="profile_load" name="/sbin/klogd" pid=1208 comm="apparmor_parser"
[ 47.648912] audit: type=1400 audit(1437494940.107:4): apparmor="STATUS" operation="profile_load" name="/sbin/syslog-ng" pid=1212 comm="apparmor_parser"
[ 47.657773] audit: type=1400 audit(1437494940.116:5): apparmor="STATUS" operation="profile_load" name="/sbin/syslogd" pid=1216 comm="apparmor_parser"
[ 47.670660] audit: type=1400 audit(1437494940.129:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/apache2/mpm-prefork/apache2" pid=1221 comm="apparmor_parser"
[ 47.670668] audit: type=1400 audit(1437494940.129:7): apparmor="STATUS" operation="profile_load" name="DEFAULT_URI" pid=1221 comm="apparmor_parser"
[ 47.670673] audit: type=1400 audit(1437494940.129:8): apparmor="STATUS" operation="profile_load" name="HANDLING_UNTRUSTED_INPUT" pid=1221 comm="apparmor_parser"
[ 47.670679] audit: type=1400 audit(1437494940.129:9): apparmor="STATUS" operation="profile_load" name="phpsysinfo" pid=1221 comm="apparmor_parser"
[ 47.677579] audit: type=1400 audit(1437494940.136:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/dovecot/anvil" pid=1225 comm="apparmor_parser"
[ 47.686647] audit: type=1400 audit(1437494940.145:11): apparmor="STATUS" operation="profile_load" name="/usr/lib/dovecot/auth" pid=1229 comm="apparmor_parser"
[ 47.916852] it87: Found IT8720F chip at 0x228, revision 8
[ 47.916878] it87: Routing internal VCCH to in7
[ 47.916882] it87: Beeping is supported
[ 48.193901] <6>[fglrx] Firegl kernel thread PID: 1840
[ 48.193985] <6>[fglrx] Firegl kernel thread PID: 1841
[ 48.194063] <6>[fglrx] Firegl kernel thread PID: 1842
[ 48.194172] <6>[fglrx] IRQ 28 Enabled
[ 48.261580] <6>[fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 48.261586] <6>[fglrx] Reserved FB block: Unshared offset:f7b4000, size:4000
[ 48.261587] <6>[fglrx] Reserved FB block: Unshared offset:f7b8000, size:548000
[ 48.261588] <6>[fglrx] Reserved FB block: Unshared offset:3fff3000, size:d000
[ 66.833962] fuse init (API version 7.23)
[ 79.574883] tun: Universal TUN/TAP device driver, 1.6
[ 79.574890] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 84.830242] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 84.835380] device tap0 entered promiscuous mode
[ 84.838052] device tap1 entered promiscuous mode
[ 84.840604] device tap2 entered promiscuous mode
[ 84.844187] device tap3 entered promiscuous mode
[ 84.848473] device tap4 entered promiscuous mode
[ 84.852358] device tap11 entered promiscuous mode
[ 91.976694] device tap5 entered promiscuous mode
[ 91.979799] device tap6 entered promiscuous mode
[ 91.982923] device tap9 entered promiscuous mode
[ 97.991404] ata1.00: configured for UDMA/133
[ 97.991411] ata1: EH complete
[ 97.995681] RPC: Registered named UNIX socket transport module.
[ 97.995684] RPC: Registered udp transport module.
[ 97.995685] RPC: Registered tcp transport module.
[ 97.995686] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 97.999686] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 98.053937] VFIO - User Level meta-driver version: 0.3
[ 98.058156] firewire_ohci 0000:06:0e.0: removed fw-ohci device
[ 98.174346] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 98.174499] NFSD: starting 90-second grace period (net ffffffff81ed7c00)
[ 100.177429] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 100.190442] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 100.435527] br0: port 1(tap0) entered forwarding state
[ 100.435536] br0: port 1(tap0) entered forwarding state
[ 100.438351] br1: port 2(tap6) entered forwarding state
[ 100.438357] br1: port 2(tap6) entered forwarding state
[ 100.438455] br0: port 5(tap4) entered forwarding state
[ 100.438458] br0: port 5(tap4) entered forwarding state
[ 100.778246] kvm: zapping shadow pages for mmio generation wraparound
[ 100.864462] kvm: zapping shadow pages for mmio generation wraparound
[ 102.970656] kvm [9802]: vcpu0 unimplemented perfctr wrmsr: 0xc0010004 data 0xffff
[ 105.361778] kvm [9800]: vcpu0 unimplemented perfctr wrmsr: 0xc0010004 data 0xffff
[ 105.542200] br0: port 2(tap1) entered forwarding state
[ 105.542208] br0: port 2(tap1) entered forwarding state
[ 105.700420] vfio-pci 0000:06:06.0: enabling device (0000 -> 0003)
[ 109.158570] kvm: zapping shadow pages for mmio generation wraparound
[ 110.614762] br1: port 1(tap5) entered forwarding state
[ 110.614770] br1: port 1(tap5) entered forwarding state
[ 110.630890] br0: port 4(tap3) entered forwarding state
[ 110.630901] br0: port 4(tap3) entered forwarding state
[ 111.062493] kvm: zapping shadow pages for mmio generation wraparound
[ 111.146884] kvm: zapping shadow pages for mmio generation wraparound
[ 112.169430] kvm [9887]: vcpu0 unimplemented perfctr wrmsr: 0xc0010004 data 0xabcd
[ 113.199284] kvm [10000]: vcpu0 unimplemented perfctr wrmsr: 0xc0010004 data 0xffff
[ 115.510642] kvm [9996]: vcpu0 unhandled rdmsr: 0xc0010112
[ 115.642579] kvm [9996]: vcpu0 unhandled rdmsr: 0xc0011021
[ 115.679777] kvm [9996]: vcpu0 unimplemented perfctr wrmsr: 0xc0010004 data 0xffff
[ 119.736038] kvm [9996]: vcpu0 unhandled rdmsr: 0x3a
[ 119.736044] kvm [9996]: vcpu0 unhandled rdmsr: 0xd90
