Hi Liviu,
You're right, i removed configuration space from the ranges.
Thanks for reviewing.
Gabriel
On 17 March 2015 at 12:42, Liviu Dudau <Liviu.Dudau@xxxxxxx> wrote:
> Hi Gabriel,
>
> On Mon, Mar 16, 2015 at 02:20:32PM +0000, Gabriel FERNANDEZ wrote:
>> sti pcie is built around a Synopsis Designware PCIe IP.
>>
>> Signed-off-by: Fabrice Gasnier <fabrice.gasnier@xxxxxx>
>> Signed-off-by: Gabriel Fernandez <gabriel.fernandez@xxxxxxxxxx>
>> ---
>> Documentation/devicetree/bindings/pci/st-pcie.txt | 54 +++++++++++++++++++++++
>> 1 file changed, 54 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pci/st-pcie.txt
>>
>> diff --git a/Documentation/devicetree/bindings/pci/st-pcie.txt b/Documentation/devicetree/bindings/pci/st-pcie.txt
>> new file mode 100644
>> index 0000000..94aae2d
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/st-pcie.txt
>> @@ -0,0 +1,54 @@
>> +STMicroelectronics STi PCIe controller
>> +
>> +This PCIe host controller is based on the Synopsis Designware PCIe IP
>> +and thus inherits all the common properties defined in designware-pcie.txt.
>> +
>> +Required properties:
>> + - compatible: "st,stih407-pcie"
>> + - reg: base address and length of the pcie controller, mem-window address
>> + and length available to the controller.
>> + - interrupts: A list of interrupt outputs of the controller. Must contain an
>> + entry for each entry in the interrupt-names property.
>> + - interrupt-names: Should be "msi". STi interrupt that is asserted when an
>> + MSI is received.
>> + - st,syscfg : should be a phandle of the syscfg node. Also contains syscfg
>> + offset for IP configuration.
>> + - resets, reset-names: the power-down and soft-reset lines of PCIe IP.
>> + Associated names must be "powerdown" and "softreset".
>> + - phys, phy-names: the phandle for the PHY device.
>> + Associated name must be "pcie"
>> +
>> +Optional properties:
>> + - reset-gpio: a GPIO spec to define which pin is connected to the bus reset.
>> +
>> +Example:
>> +
>> +pcie0: pcie@9b00000 {
>> + compatible = "st,stih407-pcie", "snps,dw-pcie";
>> + device_type = "pci";
>> + reg = <0x09b00000 0x4000>, /* dbi cntrl registers */
>> + <0x2fff0000 0x00010000>, /* configuration space */
>> + <0x40000000 0x80000000>; /* lmi mem window */
>> + reg-names = "dbi", "config", "mem-window";
>> + st,syscfg = <&syscfg_core 0xd8 0xe0>;
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> + ranges = <0x00000800 0 0x2fff0000 0x2fff0000 0 0x00010000 /* configuration space */
>
> Unless you are trying to support some legacy code please remove the configuration space from the ranges.
> There is no resource type associated with config space and the generic parser will give you back an
> invalid resource type. The other reason for that is that if you really claim to be ECAM compliant by
> adding the config space here you need way more than 64K of space.
>
> Best regards,
> Liviu
>
>> + 0x82000000 0 0x20000000 0x20000000 0 0x0FFF0000>; /* non-prefetchable memory */
>> + num-lanes = <1>;
>> + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "msi";
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 7>;
>> + interrupt-map = <0 0 0 1 &intc GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, /* INT A */
>> + <0 0 0 2 &intc GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, /* INT B */
>> + <0 0 0 3 &intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, /* INT C */
>> + <0 0 0 4 &intc GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>; /* INT D */
>> +
>> + resets = <&powerdown STIH407_PCIE0_POWERDOWN>,
>> + <&softreset STIH407_PCIE0_SOFTRESET>;
>> + reset-names = "powerdown",
>> + "softreset";
>> + phys = <&phy_port0 PHY_TYPE_PCIE>;
>> + phy-names = "pcie";
>> +};
>> --
>> 1.9.1
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>
>
> --
> ====================
> | I would like to |
> | fix the world, |
> | but they're not |
> | giving me the |
> \ source code! /
> ---------------
> ¯\_(ツ)_/¯
>
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
