Hi Bjorn,
On 3/10/2015 2:40 PM, Bjorn Helgaas wrote:
> [+cc Rob, Yijing]
>
> On Mon, Mar 09, 2015 at 05:38:05PM -0700, Ray Jui wrote:
>> This adds the support for Broadcom iProc PCIe controller
>>
>> pcie-iproc.c servers as the common core driver, and front-end bus
>> interface needs to be added to support different bus interfaces
>>
>> pcie-iproc-pltfm.c contains the support for the platform bus interface
>>
>> Signed-off-by: Ray Jui <rjui@xxxxxxxxxxxx>
>> Reviewed-by: Scott Branden <sbraden@xxxxxxxxxxxx>
>> ---
>> drivers/pci/host/Kconfig | 17 ++
>> drivers/pci/host/Makefile | 2 +
>> drivers/pci/host/pcie-iproc-pltfm.c | 108 +++++++++++
>> drivers/pci/host/pcie-iproc.c | 351 +++++++++++++++++++++++++++++++++++
>> drivers/pci/host/pcie-iproc.h | 42 +++++
>> 5 files changed, 520 insertions(+)
>> create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c
>> create mode 100644 drivers/pci/host/pcie-iproc.c
>> create mode 100644 drivers/pci/host/pcie-iproc.h
>>
>> diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
>> index 7b892a9..f4d9c90 100644
>> --- a/drivers/pci/host/Kconfig
>> +++ b/drivers/pci/host/Kconfig
>> @@ -106,4 +106,21 @@ config PCI_VERSATILE
>> bool "ARM Versatile PB PCI controller"
>> depends on ARCH_VERSATILE
>>
>> +config PCIE_IPROC
>> + tristate "Broadcom iProc PCIe controller"
>> + help
>> + This enables the iProc PCIe core controller support for Broadcom's
>> + iProc family of SoCs. An appropriate bus interface driver also needs
>> + to be enabled
>> +
>> +config PCIE_IPROC_PLTFM
>> + tristate "Broadcom iProc PCIe platform bus driver"
>> + depends on ARCH_BCM_IPROC || COMPILE_TEST
>> + depends on OF
>> + select PCIE_IPROC
>> + default ARCH_BCM_IPROC
>> + help
>> + Say Y here if you want to use the Broadcom iProc PCIe controller
>> + through the generic platform bus interface
>
> Do you anticipate additional front-end bus interfaces? If not, and maybe
> even if you do, you might squash everything into pcie-iproc.c. Then you
> only need one file (no .h file needed) and the package is a little
> simpler. I think it's pretty common to have multiple driver registration
> methods in the same file (OF, PCI, ACPI, etc.) And I think it's common to
> have those methods guarded by the generic config symbol (CONFIG_PCI,
> CONFIG_OF, etc.) rather than defining new ones specific to the driver.
>
Yes I do expect Hauke (CCed) to add BCMA bus front end support later.
I still think having the front end bus driver separated is cleaner and
may be less troublesome for Hauke to add BCMA support in the future. But
if you strongly favor having everything stuffed in one single file, I
can make that change. Please let me know.
>> +
>> endmenu
>> diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
>> index e61d91c..2e02d20 100644
>> --- a/drivers/pci/host/Makefile
>> +++ b/drivers/pci/host/Makefile
>> @@ -13,3 +13,5 @@ obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
>> obj-$(CONFIG_PCI_XGENE) += pci-xgene.o
>> obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o
>> obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o
>> +obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o
>> +obj-$(CONFIG_PCIE_IPROC_PLTFM) += pcie-iproc-pltfm.o
>> diff --git a/drivers/pci/host/pcie-iproc-pltfm.c b/drivers/pci/host/pcie-iproc-pltfm.c
>> new file mode 100644
>> index 0000000..af935ea
>> --- /dev/null
>> +++ b/drivers/pci/host/pcie-iproc-pltfm.c
>> @@ -0,0 +1,108 @@
>> +/*
>> + * Copyright (C) 2015 Broadcom Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/pci.h>
>> +#include <linux/clk.h>
>> +#include <linux/module.h>
>> +#include <linux/slab.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_pci.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/phy/phy.h>
>> +
>> +#include "pcie-iproc.h"
>> +
>> +static int __init iproc_pcie_pltfm_probe(struct platform_device *pdev)
>> +{
>> + struct iproc_pcie *pcie;
>> + struct device_node *np = pdev->dev.of_node;
>> + struct resource reg;
>> + resource_size_t iobase = 0;
>> + LIST_HEAD(res);
>> + int ret;
>> +
>> + pcie = devm_kzalloc(&pdev->dev, sizeof(struct iproc_pcie), GFP_KERNEL);
>> + if (!pcie)
>> + return -ENOMEM;
>> +
>> + pcie->dev = &pdev->dev;
>> + platform_set_drvdata(pdev, pcie);
>> +
>> + ret = of_address_to_resource(np, 0, ®);
>> + if (ret < 0) {
>> + dev_err(pcie->dev, "unable to obtain controller resources\n");
>> + return ret;
>> + }
>> +
>> + pcie->base = devm_ioremap(pcie->dev, reg.start, resource_size(®));
>> + if (!pcie->base) {
>> + dev_err(pcie->dev, "unable to map controller registers\n");
>> + return -ENOMEM;
>> + }
>> +
>> + /* PHY use is optional */
>> + pcie->phy = devm_phy_get(&pdev->dev, "pcie-phy");
>> + if (IS_ERR(pcie->phy)) {
>> + if (PTR_ERR(pcie->phy) == -EPROBE_DEFER)
>> + return -EPROBE_DEFER;
>> + pcie->phy = NULL;
>> + }
>> +
>> + ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &iobase);
>> + if (ret) {
>> + dev_err(pcie->dev,
>> + "unable to get PCI host bridge resources\n");
>> + return ret;
>> + }
>> +
>> + pcie->resources = &res;
>> +
>> + ret = iproc_pcie_setup(pcie);
>> + if (ret) {
>> + dev_err(pcie->dev, "PCIe controller setup failed\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int iproc_pcie_pltfm_remove(struct platform_device *pdev)
>> +{
>> + struct iproc_pcie *pcie = platform_get_drvdata(pdev);
>> +
>> + return iproc_pcie_remove(pcie);
>> +}
>> +
>> +static const struct of_device_id iproc_pcie_of_match_table[] = {
>> + { .compatible = "brcm,iproc-pcie", },
>> + { /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, iproc_pcie_of_match_table);
>> +
>> +static struct platform_driver iproc_pcie_pltfm_driver = {
>> + .driver = {
>> + .name = "iproc-pcie",
>> + .of_match_table = of_match_ptr(iproc_pcie_of_match_table),
>> + },
>> + .probe = iproc_pcie_pltfm_probe,
>> + .remove = iproc_pcie_pltfm_remove,
>> +};
>> +module_platform_driver(iproc_pcie_pltfm_driver);
>> +
>> +MODULE_AUTHOR("Ray Jui <rjui@xxxxxxxxxxxx>");
>> +MODULE_DESCRIPTION("Broadcom iPROC PCIe platform driver");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/pci/host/pcie-iproc.c b/drivers/pci/host/pcie-iproc.c
>> new file mode 100644
>> index 0000000..ad6c89e
>> --- /dev/null
>> +++ b/drivers/pci/host/pcie-iproc.c
>> @@ -0,0 +1,351 @@
>> +/*
>> + * Copyright (C) 2014 Hauke Mehrtens <hauke@xxxxxxxxxx>
>> + * Copyright (C) 2015 Broadcom Corporatcommon ion
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/pci.h>
>> +#include <linux/msi.h>
>> +#include <linux/clk.h>
>> +#include <linux/module.h>
>> +#include <linux/mbus.h>
>> +#include <linux/slab.h>
>> +#include <linux/delay.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_pci.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/phy/phy.h>
>> +
>> +#include "pcie-iproc.h"
>> +
>> +#define CLK_CONTROL_OFFSET 0x000
>> +#define EP_MODE_SURVIVE_PERST_SHIFT 1
>> +#define EP_MODE_SURVIVE_PERST BIT(EP_MODE_SURVIVE_PERST_SHIFT)
>> +#define RC_PCIE_RST_OUTPUT_SHIFT 0
>> +#define RC_PCIE_RST_OUTPUT BIT(RC_PCIE_RST_OUTPUT_SHIFT)
>> +
>> +#define CFG_IND_ADDR_OFFSET 0x120
>> +#define CFG_IND_ADDR_MASK 0x00001ffc
>> +
>> +#define CFG_IND_DATA_OFFSET 0x124
>> +
>> +#define CFG_ADDR_OFFSET 0x1f8
>> +#define CFG_ADDR_BUS_NUM_SHIFT 20
>> +#define CFG_ADDR_BUS_NUM_MASK 0x0ff00000
>> +#define CFG_ADDR_DEV_NUM_SHIFT 15
>> +#define CFG_ADDR_DEV_NUM_MASK 0x000f8000
>> +#define CFG_ADDR_FUNC_NUM_SHIFT 12
>> +#define CFG_ADDR_FUNC_NUM_MASK 0x00007000
>> +#define CFG_ADDR_REG_NUM_SHIFT 2
>> +#define CFG_ADDR_REG_NUM_MASK 0x00000ffc
>> +#define CFG_ADDR_CFG_TYPE_SHIFT 0
>> +#define CFG_ADDR_CFG_TYPE_MASK 0x00000003
>> +
>> +#define CFG_DATA_OFFSET 0x1fc
>> +
>> +#define SYS_RC_INTX_EN 0x330
>> +#define SYS_RC_INTX_MASK 0xf
>> +
>> +static inline struct iproc_pcie *sys_to_pcie(struct pci_sys_data *sys)
>> +{
>> + return sys->private_data;
>> +}
>> +
>> +#define INVALID_ACCESS_OFFSET 0xffffffff
>> +static u32 iproc_pcie_cfg_base(struct iproc_pcie *pcie, int busno,
>> + unsigned int devfn, int where)
>> +{
>> + int slot = PCI_SLOT(devfn);
>> + int fn = PCI_FUNC(devfn);
>> + u32 val;
>> +
>
> Would you mind adding a comment to the effect that
> CFG_IND_ADDR_OFFSET/CFG_IND_DATA_OFFSET and
> CFG_ADDR_OFFSET/CFG_DATA_OFFSET are protected by pci_lock?
>
> They obviously need a mutex, and while I don't have any plans to
> change it, I'm not completely 100% sure that pci_lock is the best
> place for it.
>
Sorry I don't get what you want me to do here. Do you want me to add
some comment to explain that the struct pci_ops read/write callbacks are
already protected at the upper layer by the pci_lock spinlock and
therefore no lock is required in this driver?
>> + /* root complex access */
>> + if (busno == 0) {
>> + if (slot >= 1)
>> + return INVALID_ACCESS_OFFSET;
>> + writel(where & CFG_IND_ADDR_MASK,
>> + pcie->base + CFG_IND_ADDR_OFFSET);
>> + return CFG_IND_DATA_OFFSET;
>> + }
>> +
>> + if (fn > 1)
>> + return INVALID_ACCESS_OFFSET;
>> +
>> + /* EP device access */
>> + val = (busno << CFG_ADDR_BUS_NUM_SHIFT) |
>> + (slot << CFG_ADDR_DEV_NUM_SHIFT) |
>> + (fn << CFG_ADDR_FUNC_NUM_SHIFT) |
>> + (where & CFG_ADDR_REG_NUM_MASK) |
>> + (1 & CFG_ADDR_CFG_TYPE_MASK);
>> + writel(val, pcie->base + CFG_ADDR_OFFSET);
>> +
>> + return CFG_DATA_OFFSET;
>> +}
>> +
>> +#define INVALID_CFG_RD 0xffffffff
>> +static int iproc_pcie_read_conf(struct iproc_pcie *pcie, int busno,
>> + unsigned int devfn, int where, int size,
>> + u32 *val)
>> +{
>> + u32 offset, mask, shift;
>> +
>> + *val = INVALID_CFG_RD;
>> +
>> + if (size != 1 && size != 2 && size != 4)
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> + else if ((size == 2) && (where & 1))
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> + else if ((size == 4) && (where & 3))
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> +
>> + offset = iproc_pcie_cfg_base(pcie, busno, devfn, where);
>> + if (offset == INVALID_ACCESS_OFFSET)
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> +
>> + *val = readl(pcie->base + offset);
>> +
>> + if (size != 4) {
>> + mask = (1 << (size * BITS_PER_BYTE)) - 1;
>> + shift = (where % 4) * BITS_PER_BYTE;
>> + *val = (*val >> shift) & mask;
>> + }
>> +
>> + dev_dbg(pcie->dev,
>> + "conf rd: busn=%d devfn=%u where=%d size=%d val=0x%08x\n",
>> + busno, devfn, where, size, *val);
>> +
>> + return PCIBIOS_SUCCESSFUL;
>> +}
>
> This looks like maybe it could use Rob Herring's (CC'd) new generic config
> accessors? For example, see these:
>
> 1f94a94f67e1 ("PCI: Add generic config accessors")
> 21186728865e ("PCI: generic: Convert to use generic config accessors")
>
Okay I will switch to use the generic code for config space access. I'll
add map_bus callback for address calculation.
>> +
>> +static int iproc_pcie_write_conf(struct iproc_pcie *pcie, int busno,
>> + unsigned int devfn, int where, int size,
>> + u32 val)
>> +{
>> + u32 offset, mask, shift, data;
>> +
>> + if (size != 1 && size != 2 && size != 4)
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> + else if ((size == 2) && (where & 1))
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> + else if ((size == 4) && (where & 3))
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> +
>> + offset = iproc_pcie_cfg_base(pcie, busno, devfn, where);
>> + if (offset == INVALID_ACCESS_OFFSET)
>> + return PCIBIOS_BAD_REGISTER_NUMBER;
>> +
>> + data = readl(pcie->base + offset);
>> +
>> + if (size != 4) {
>> + mask = (1 << (size * BITS_PER_BYTE)) - 1;
>> + shift = (where % 4) * BITS_PER_BYTE;
>> + data &= ~(mask << shift);
>> + data |= (val & mask) << shift;
>> + } else {
>> + data = val;
>> + }
>> +
>> + writel(data, pcie->base + offset);
>> +
>> + dev_dbg(pcie->dev,
>> + "conf wr: busn=%d devfn=%u where=%d size=%d data=0x%08x\n",
>> + busno, devfn, where, size, data);
>> +
>> + return PCIBIOS_SUCCESSFUL;
>> +}
>> +
>> +static int iproc_pcie_read(struct pci_bus *bus, unsigned int devfn,
>> + int where, int size, u32 *val)
>> +{
>> + struct iproc_pcie *pcie = sys_to_pcie(bus->sysdata);
>> +
>> + return iproc_pcie_read_conf(pcie, bus->number, devfn, where, size,
>> + val);
>> +}
>> +
>> +static int iproc_pcie_write(struct pci_bus *bus, unsigned int devfn,
>> + int where, int size, u32 val)
>> +{
>> + struct iproc_pcie *pcie = sys_to_pcie(bus->sysdata);
>> +
>> + return iproc_pcie_write_conf(pcie, bus->number, devfn, where, size,
>> + val);
>> +}
>> +
>> +static struct pci_ops iproc_pcie_ops = {
>> + .read = iproc_pcie_read,
>> + .write = iproc_pcie_write,
>> +};
>> +
>> +static void iproc_pcie_reset(struct iproc_pcie *pcie)
>> +{
>> + u32 val;
>> +
>> + /*
>> + * Configure the PCIe controller as root complex and send a downstream
>> + * reset
>> + */
>> + val = EP_MODE_SURVIVE_PERST | RC_PCIE_RST_OUTPUT;
>> + writel(val, pcie->base + CLK_CONTROL_OFFSET);
>> + udelay(250);
>> + val &= ~EP_MODE_SURVIVE_PERST;
>> + writel(val, pcie->base + CLK_CONTROL_OFFSET);
>> + msleep(250);
>> +}
>> +
>> +static int iproc_pcie_check_link(struct iproc_pcie *pcie, struct pci_bus *bus)
>> +{
>> + u8 hdr_type;
>> + u32 link_ctrl;
>> + u16 pos, link_status;
>> + int link_is_active = 0;
>> +
>> + /* make sure we are not in EP mode */
>> + pci_bus_read_config_byte(bus, 0, PCI_HEADER_TYPE, &hdr_type);
>> + if ((hdr_type & 0x7f) != PCI_HEADER_TYPE_BRIDGE) {
>> + dev_err(pcie->dev, "in EP mode, hdr=0x08%x\n", hdr_type);
>> + return -EFAULT;
>> + }
>> +
>> + /* force class to PCI_CLASS_BRIDGE_PCI (0x0604) */
>> + pci_bus_write_config_word(bus, 0, PCI_CLASS_DEVICE,
>> + PCI_CLASS_BRIDGE_PCI);
>> +
>> + /* check link status to see if link is active */
>> + pos = pci_bus_find_capability(bus, 0, PCI_CAP_ID_EXP);
>> + pci_bus_read_config_word(bus, 0, pos + PCI_EXP_LNKSTA, &link_status);
>> + if (link_status & PCI_EXP_LNKSTA_NLW)
>> + link_is_active = 1;
>> +
>> + if (!link_is_active) {
>> + /* try GEN 1 link speed */
>> +#define PCI_LINK_STATUS_CTRL_2_OFFSET 0x0dc
>> +#define PCI_TARGET_LINK_SPEED_MASK 0xf
>> +#define PCI_TARGET_LINK_SPEED_GEN2 0x2
>> +#define PCI_TARGET_LINK_SPEED_GEN1 0x1
>> + pci_bus_read_config_dword(bus, 0,
>> + PCI_LINK_STATUS_CTRL_2_OFFSET,
>> + &link_ctrl);
>> + if ((link_ctrl & PCI_TARGET_LINK_SPEED_MASK) ==
>> + PCI_TARGET_LINK_SPEED_GEN2) {
>> + link_ctrl &= ~PCI_TARGET_LINK_SPEED_MASK;
>> + link_ctrl |= PCI_TARGET_LINK_SPEED_GEN1;
>> + pci_bus_write_config_dword(bus, 0,
>> + PCI_LINK_STATUS_CTRL_2_OFFSET,
>> + link_ctrl);
>> + msleep(100);
>> +
>> + pos = pci_bus_find_capability(bus, 0, PCI_CAP_ID_EXP);
>> + pci_bus_read_config_word(bus, 0, pos + PCI_EXP_LNKSTA,
>> + &link_status);
>> + if (link_status & PCI_EXP_LNKSTA_NLW)
>> + link_is_active = 1;
>> + }
>> + }
>> +
>> + dev_info(pcie->dev, "link: %s\n", link_is_active ? "UP" : "DOWN");
>> +
>> + return link_is_active ? 0 : -ENODEV;
>> +}
>> +
>> +static void iproc_pcie_enable(struct iproc_pcie *pcie)
>> +{
>> + writel(SYS_RC_INTX_MASK, pcie->base + SYS_RC_INTX_EN);
>> +}
>> +
>> +int iproc_pcie_setup(struct iproc_pcie *pcie)
>> +{
>> + int ret;
>> + struct pci_bus *bus;
>> +
>> + if (!pcie || !pcie->dev || !pcie->base)
>> + return -EINVAL;
>> +
>> + if (pcie->phy) {
>> + ret = phy_init(pcie->phy);
>> + if (ret) {
>> + dev_err(pcie->dev, "unable to initialize PCIe PHY\n");
>> + return ret;
>> + }
>> +
>> + ret = phy_power_on(pcie->phy);
>> + if (ret) {
>> + dev_err(pcie->dev, "unable to power on PCIe PHY\n");
>> + goto err_exit_phy;
>> + }
>> +
>> + }
>> +
>> + iproc_pcie_reset(pcie);
>> +
>> + pcie->sysdata.private_data = pcie;
>> +
>> + bus = pci_create_root_bus(pcie->dev, 0, &iproc_pcie_ops,
>> + &pcie->sysdata, pcie->resources);
>> + if (!bus) {
>> + dev_err(pcie->dev, "unable to create PCI root bus\n");
>> + ret = -ENOMEM;
>> + goto err_power_off_phy;
>> + }
>> + pcie->root_bus = bus;
>> +
>> + ret = iproc_pcie_check_link(pcie, bus);
>> + if (ret) {
>> + dev_err(pcie->dev, "no PCIe EP device detected\n");
>> + goto err_rm_root_bus;
>> + }
>> +
>> + iproc_pcie_enable(pcie);
>> +
>> + pci_scan_child_bus(bus);
>> + pci_assign_unassigned_bus_resources(bus);
>> + pci_bus_add_devices(bus);
>> +
>> + pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
>
> I think the IRQ fixup should be before pci_bus_add_devices(). CC'd Yijing,
> who's been fixing similar issues.
>
> pci_bus_add_devices() is the point where drivers can claim these devices,
> and we don't want to change things after a driver claims the device.
>
Right. I will fix this.
>> +
>> + return 0;
>> +
>> +err_rm_root_bus:
>> + pci_stop_root_bus(bus);
>> + pci_remove_root_bus(bus);
>> +
>> +err_power_off_phy:
>> + if (pcie->phy)
>> + phy_power_off(pcie->phy);
>> +err_exit_phy:
>> + if (pcie->phy)
>> + phy_exit(pcie->phy);
>> +
>> + return ret;
>> +}
>> +EXPORT_SYMBOL(iproc_pcie_setup);
>> +
>> +int iproc_pcie_remove(struct iproc_pcie *pcie)
>> +{
>> + pci_stop_root_bus(pcie->root_bus);
>> + pci_remove_root_bus(pcie->root_bus);
>> +
>> + if (pcie->phy) {
>> + phy_power_off(pcie->phy);
>> + phy_exit(pcie->phy);
>> + }
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL(iproc_pcie_remove);
>
> These exports wouldn't be needed if this were all squashed into one file.
>
Understood. Let's decide whether or not to keep everything in one file.
>> +
>> +MODULE_AUTHOR("Ray Jui <rjui@xxxxxxxxxxxx>");
>> +MODULE_DESCRIPTION("Broadcom iPROC PCIe common driver");
>> +MODULE_LICENSE("GPL v2");
>> diff --git a/drivers/pci/host/pcie-iproc.h b/drivers/pci/host/pcie-iproc.h
>> new file mode 100644
>> index 0000000..569bc04
>> --- /dev/null
>> +++ b/drivers/pci/host/pcie-iproc.h
>> @@ -0,0 +1,42 @@
>> +/*
>> + * Copyright (C) 2014-2015 Broadcom Corporation
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation version 2.
>> + *
>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>> + * kind, whether express or implied; without even the implied warranty
>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + */
>> +
>> +#ifndef _PCIE_IPROC_H
>> +#define _PCIE_IPROC_H
>> +
>> +#define IPROC_PCIE_MAX_NUM_IRQS 6
>> +
>> +/**
>> + * iProc PCIe device
>> + * @dev: pointer to device data structure
>> + * @base: PCIe host controller I/O register base
>> + * @resources: linked list of all PCI resources
>> + * @sysdata: Per PCI controller data
>> + * @root_bus: pointer to root bus
>> + * @phy: optional PHY device that controls the Serdes
>> + * @irqs: interrupt IDs
>> + */
>> +struct iproc_pcie {
>> + struct device *dev;
>> + void __iomem *base;
>> + struct list_head *resources;
>> + struct pci_sys_data sysdata;
>> + struct pci_bus *root_bus;
>> + struct phy *phy;
>> + int irqs[IPROC_PCIE_MAX_NUM_IRQS];
>> +};
>> +
>> +extern int iproc_pcie_setup(struct iproc_pcie *pcie);
>> +extern int iproc_pcie_remove(struct iproc_pcie *pcie);
>
> Hopefully you can squash this all into one file, but if you can't, my
> preference is to omit "extern" on function declarations.
>
>> +
>> +#endif /* _PCIE_IPROC_H */
>> --
>> 1.7.9.5
>>
Thanks for the review!
Ray
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
