On Wed, Nov 26, 2014 at 10:03:59AM +1100, Gavin Shan wrote:
>On Tue, Nov 25, 2014 at 05:11:14PM +0800, Wei Yang wrote:
>>On Tue, Nov 25, 2014 at 02:46:52PM +1100, Gavin Shan wrote:
>>>On Tue, Nov 25, 2014 at 11:14:55AM +0800, Wei Yang wrote:
>>>>On Tue, Nov 25, 2014 at 10:01:08AM +1100, Gavin Shan wrote:
>>>>>On Sat, Nov 22, 2014 at 10:52:39AM +0800, Wei Yang wrote:
>>>>>>According to SR-IOV spec sec 3.3.9, 3.3.10, the NumVFs setting change will
>>>>>>affect the offset and stride. Current implementation doesn't refresh the
>>>>>>offset/stride cached in pci_sriov structure.
>>>>>>
>>>>>>This patch introduces a wrapper pci_iov_set_numvfs(), which refresh these two
>>>>>>value after NumVFs is written.
>>>>>>
>>>>>>Signed-off-by: Wei Yang <weiyang@xxxxxxxxxxxxxxxxxx>
>>>>>>---
>>>>>> drivers/pci/iov.c | 17 +++++++++++++----
>>>>>> 1 file changed, 13 insertions(+), 4 deletions(-)
>>>>>>
>>>>>>diff --git a/drivers/pci/iov.c b/drivers/pci/iov.c
>>>>>>index 4d109c0..c7010c5 100644
>>>>>>--- a/drivers/pci/iov.c
>>>>>>+++ b/drivers/pci/iov.c
>>>>>>@@ -31,6 +31,15 @@ static inline u8 virtfn_devfn(struct pci_dev *dev, int id)
>>>>>> dev->sriov->stride * id) & 0xff;
>>>>>> }
>>>>>>
>>>>>>+static inline void pci_iov_set_numvfs(struct pci_dev *dev, int nr_virtfn)
>>>>>>+{
>>>>>>+ struct pci_sriov *iov = dev->sriov;
>>>>>>+
>>>>>>+ pci_write_config_word(dev, iov->pos + PCI_SRIOV_NUM_VF, nr_virtfn);
>>>>>
>>>>>I'm suspecting writing to PCI_SRIOV_NUM_VF would take some time to take
>>>>>effect.
>>>>>
>>>>>>+ pci_read_config_word(dev, iov->pos + PCI_SRIOV_VF_OFFSET, &iov->offset);
>>>>>>+ pci_read_config_word(dev, iov->pos + PCI_SRIOV_VF_STRIDE, &iov->stride);
>>>>>>+}
>>>>>>+
>>>>>> static struct pci_bus *virtfn_add_bus(struct pci_bus *bus, int busnr)
>>>>>> {
>>>>>> struct pci_bus *child;
>>>>>>@@ -243,7 +252,7 @@ static int sriov_enable(struct pci_dev *dev, int nr_virtfn)
>>>>>> return rc;
>>>>>> }
>>>>>>
>>>>>>- pci_write_config_word(dev, iov->pos + PCI_SRIOV_NUM_VF, nr_virtfn);
>>>>>>+ pci_iov_set_numvfs(dev, nr_virtfn);
>>>>>> iov->ctrl |= PCI_SRIOV_CTRL_VFE | PCI_SRIOV_CTRL_MSE;
>>>>>> pci_cfg_access_lock(dev);
>>>>>> pci_write_config_word(dev, iov->pos + PCI_SRIOV_CTRL, iov->ctrl);
>>>>>>@@ -272,7 +281,7 @@ failed:
>>>>>> iov->ctrl &= ~(PCI_SRIOV_CTRL_VFE | PCI_SRIOV_CTRL_MSE);
>>>>>> pci_cfg_access_lock(dev);
>>>>>> pci_write_config_word(dev, iov->pos + PCI_SRIOV_CTRL, iov->ctrl);
>>>>>>- pci_write_config_word(dev, iov->pos + PCI_SRIOV_NUM_VF, 0);
>>>>>>+ pci_iov_set_numvfs(dev, 0);
>>>>>> ssleep(1);
>>>>>
>>>>>The 1 second delay here might be for waiting VFs to be ready.
>>>>>
>>>>
>>>>Hmm... so add this ssleep() in pci_iov_set_numvfs() would be better?
>>>>
>>>
>>>I was not suggesting to do that. I just raised the concern for you
>>>to look into.
>>>
>>
>>I looked in the SPEC sec 3.3.3.1 VF Enable. In this section, it says this:
>>
>>To allow components to perform internal initialization, system software must wait for at least
>>100 ms after changing the VF Enable bit from a 0 to a 1, before it is permitted to issue Requests to
>>the VFs which are enabled by that VF Enable bit. The Root Complex and/or system software must
>>allow at least 1.0 s after Setting the VF Enable bit, before it may determine that a VF which fails to
>>return a Successful Completion status for a valid Configuration Request is broken. After Setting the
>>VF Enable bit, the VFs enabled by that VF Enable bit are permitted to return a CRS status to
>>configuration requests up to the 1.0 s limit, if they are not ready to provide a Successful Completion
>>status for a valid Configuration Request. Additionally, a VF is not permitted to return CRS after
>>having previously returned a Successful Completion without an intervening VF disable or other valid
>>reset condition.
>>
>>As my understanding, it will take 1ms or 1s after VF Enable bit is set.
>>Actually I am confused with the two different time, in which case we needs to
>>wait for different time? And some place we add a lock, but no lock in others.
>>
>
>Are you talking about 1ms or 100ms? I assume it's 100ms. If I
>understand things correctly, 100ms delay before issuing config
>read request, CRS can be returned before it reaches the timeout
>(1 second).
Took a look at the sleep again. There are five sleep in iov.c, two are 100ms
sleep and three are 1s sleep. 100ms sleep are both after VF Enable is set. 1s
sleep are all after VF Enable is cleared. These are stated in SRIOV SPEC
3.3.3.1.
While I still suggest to wait 1s after VF Enable is set. Otherwise we need to
add some logic like pci_bus_read_dev_vendor_id() on VF to check whether VF is
ready, when CRS Software Visibility is enabled on the Bridge. Like in
sriov_enable(), the msleep() needs to be replaced by a call on a VF, while
the VF is not created in the system yet.
If my understanding is not correct, please let me know.
>
>Thanks,
>Gavin
--
Richard Yang
Help you, Help me
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
