On Thu, Nov 20, 2014 at 12:05:41PM -0700, Bjorn Helgaas wrote:
>On Thu, Nov 20, 2014 at 03:20:57PM +0800, Wei Yang wrote:
>> On Wed, Nov 19, 2014 at 04:30:24PM -0700, Bjorn Helgaas wrote:
>> >On Sun, Nov 02, 2014 at 11:41:24PM +0800, Wei Yang wrote:
>> >> From: Gavin Shan <gwshan@xxxxxxxxxxxxxxxxxx>
>> >>
>> >> pci_dn is the extension of PCI device node and it's created from
>> >> device node. Unfortunately, VFs that are enabled dynamically by
>> >> PF's driver and they don't have corresponding device nodes, and
>> >> pci_dn. The patch refactors pci_dn to support VFs:
>> >>
>> >> * pci_dn is organized as a hierarchy tree. VF's pci_dn is put
>> >> to the child list of pci_dn of PF's bridge. pci_dn of other
>> >> device put to the child list of pci_dn of its upstream bridge.
>> >>
>> >> * VF's pci_dn is expected to be created dynamically when applying
>> >> final fixup to PF. VF's pci_dn will be destroyed when releasing
>> >> PF's pci_dev instance. pci_dn of other device is still created
>> >> from device node as before.
>> >>
>> >> * For one particular PCI device (VF or not), its pci_dn can be
>> >> found from pdev->dev.archdata.firmware_data, PCI_DN(devnode),
>> >> or parent's list. The fast path (fetching pci_dn through PCI
>> >> device instance) is populated during early fixup time.
>> >>
>> >> Signed-off-by: Gavin Shan <gwshan@xxxxxxxxxxxxxxxxxx>
>> >> ---
>> >> ...
>> >
>> >> +struct pci_dn *add_dev_pci_info(struct pci_dev *pdev)
>> >> +{
>> >> +#ifdef CONFIG_PCI_IOV
>> >> + struct pci_dn *parent, *pdn;
>> >> + int i;
>> >> +
>> >> + /* Only support IOV for now */
>> >> + if (!pdev->is_physfn)
>> >> + return pci_get_pdn(pdev);
>> >> +
>> >> + /* Check if VFs have been populated */
>> >> + pdn = pci_get_pdn(pdev);
>> >> + if (!pdn || (pdn->flags & PCI_DN_FLAG_IOV_VF))
>> >> + return NULL;
>> >> +
>> >> + pdn->flags |= PCI_DN_FLAG_IOV_VF;
>> >> + parent = pci_bus_to_pdn(pdev->bus);
>> >> + if (!parent)
>> >> + return NULL;
>> >> +
>> >> + for (i = 0; i < pci_sriov_get_totalvfs(pdev); i++) {
>> >> + pdn = add_one_dev_pci_info(parent, NULL,
>> >> + pci_iov_virtfn_bus(pdev, i),
>> >> + pci_iov_virtfn_devfn(pdev, i));
>> >
>> >I'm not sure this makes sense, but I certainly don't know this code, so
>> >maybe I'm missing something.
>> >
>> >pci_iov_virtfn_bus() and pci_iov_virtfn_devfn() depend on
>> >pdev->sriov->stride and pdev->sriov->offset. These are read from VF Stride
>> >and First VF Offset in the SR-IOV capability by sriov_init(), which is
>> >called before add_dev_pci_info():
>> >
>> > pci_scan_child_bus
>> > pci_scan_slot
>> > pci_scan_single_device
>> > pci_device_add
>> > pci_init_capabilities
>> > pci_iov_init(PF)
>> > sriov_init(PF, pos)
>> > pci_write_config_word(dev, pos + PCI_SRIOV_NUM_VF, 0)
>> > pci_read_config_word(dev, pos + PCI_SRIOV_VF_OFFSET, &offset)
>> > pci_read_config_word(dev, pos + PCI_SRIOV_VF_STRIDE, &stride)
>> > iov->offset = offset
>> > iov->stride = stride
>> >
>> > pci_bus_add_devices
>> > pci_bus_add_device
>> > pci_fixup_device(pci_fixup_final)
>> > add_dev_pci_info
>> > pci_iov_virtfn_bus
>> > return ... + sriov->offset + (sriov->stride * id) ...
>> >
>> >But both First VF Offset and VF Stride change when ARI Capable Hierarchy or
>> >NumVFs changes (SR-IOV spec sec 3.3.9, 3.3.10). We set NumVFs to zero in
>> >sriov_init() above. We will change NumVFs to something different when a
>> >driver calls pci_enable_sriov():
>> >
>> > pci_enable_sriov
>> > sriov_enable
>> > pci_write_config_word(dev, iov->pos + PCI_SRIOV_NUM_VF, nr_virtfn)
>> >
>> >Now First VF Offset and VF Stride have changed from what they were when we
>> >called pci_iov_virtfn_bus() above.
>> >
>>
>> Oops, I see the ARI would affect those value, while missed the NumVFs also
>> would.
>>
>> Let's look at the problem one by one.
>>
>> 1. The ARI capability.
>> ===============================================================================
>> The kernel initialize the capability like this:
>>
>> pci_init_capabilities()
>> pci_configure_ari()
>> pci_iov_init()
>> iov->offset = offset
>> iov->stride = stride
>>
>> When offset/stride is retrieved at this point, the ARI capability is taken
>> into consideration.
>
>PCI_SRIOV_CTRL_ARI is currently only changed at the time we enumerate the
>PF, so I don't think this is really a problem.
>
>> 2. The PF's NumVFs field
>> ===============================================================================
>> 2.1 Potential problem in current code
>> ===============================================================================
>> First, is current pci code has some potential problem?
>>
>> sriov_enable()
>> pci_read_config_word(dev, iov->pos + PCI_SRIOV_VF_OFFSET, &offset);
>> pci_read_config_word(dev, iov->pos + PCI_SRIOV_VF_STRIDE, &stride);
>> iov->offset = offset;
>> iov->stride = stride;
>> pci_write_config_word(dev, iov->pos + PCI_SRIOV_NUM_VF, nr_virtfn);
>> virtfn_add()
>> ...
>> virtfn->devfn = pci_iov_virtfn_devfn(dev, id);
>>
>> The sriov_enable() retrieve the offset/stride then write the NumVFs. According
>> to the SPEC, at this moment the offset/stride may change. While I don't see
>> some code to retrieve and store those value again. And these fields will be
>> used in virtfn_add().
>>
>> If my understanding is correct, I suggest to move the retrieve and store
>> operation after NumVFs is written.
>
>Yep, it looks like the existing code has similar problems. We might want
>to add a simple function that writes PCI_SRIOV_NUM_VF, then reads
>PCI_SRIOV_VF_OFFSET and PCI_SRIOV_VF_STRIDE and refreshes the cached values
>in dev->sriov.
>
>Then we'd at least know that virtfn_bus() and virtfn_devfn() return values
>that are correct until the next NumVFs change.
>
Ok, I will write a function to wrap it.
>> 2.2 The IOV bus range may not be correct in pci_scan_child_bus()?
>> ===============================================================================
>> In current pci core, when enumerating the pci tree, we do like this:
>>
>> pci_scan_child_bus()
>> pci_scan_slot()
>> pci_scan_single_device()
>> pci_device_add()
>> pci_init_capabilities()
>> pci_iov_init()
>> max += pci_iov_bus_range(bus);
>> busnr = pci_iov_virtfn_bus(dev, dev->sriov->total_VFs - 1);
>> max = pci_scan_bridge(bus, dev, max, pass);
>>
>> From this point, we see pci core reserve some bus range for VFs. This
>> calculation is based on the offset/stride at this moment. And do the
>> enumeration with the new bus number.
>>
>> sriov_enable() could be called several times from driver to enable SRIOV, and
>> with different nr_virtfn. If each time the NumVFs written, the offset/stride
>> will change. This means we may try to address an extra bus we didn't reserve?
>> Or this means it is out of control?
>
>This looks like a problem, too. I don't have a good suggestion for fixing
>it.
How about enumerating all possible NumVFs and select the maximum?
I am not sure what will happen if the FW sets a different number? So FW should
listen to kernel, right?
I could write a code with this logic and test, while I am afraid this will
break some platfrom in some case.
>
>> 2.3 How can I reserve bus range in FW?
>> ===============================================================================
>> This question comes from the previous one.
>>
>> Based on my understanding, current pci core will rely on the bus number in HW
>> if pcibios_assign_all_busses() is not set. If we want to support those VFs
>> sits on different bus with PF, we need to reserve bus range and write the
>> correct secondary/subordinate in bridge. Otherwise, those VFs on different bus
>> may not be addressed.
>>
>> Currently I am writing the code in FW to reserve the range with the same
>> mechanism in pci core. While as you mentioned the offset/stride may change
>> after sriov_enable(), I am confused whether this is the correct way.
>
>If your firmware knows something about the device and can compute the
>number of buses it will likely need, it can set up bridges with appropriate
>bus number ranges, and Linux will generally leave those alone.
>
Yep, this is what I am trying to do.
>I don't know the best way to figure out the number of buses, though. It
>seems like you almost need to experimentally set NumVFs and read the
>resulting offset/stride, because I think it's really up to the device to
>decide how to number the VFs. Maybe pci_iov_bus_range() needs to do
>something similar.
Got it, I will add this logic.
>
>> 2.4 The potential problem for [Patch 08/18]
>> ===============================================================================
>> According to the SPEC, the offset/stride will change after each
>> sriov_enable(). This means the bus/devfn will change after each
>> sriov_enable().
>>
>> My current thought is to fix it up in virtfn_add(). If the total VF number
>> will not change, we could create those pci_dn at the beginning and fix the
>> bus/devfn at each time the VF is truely created.
>
>By "fix it up," I assume you mean call an arch function that does the
>pci_pdn setup you need.
>
>It sounds reasonable to do this either in virtfn_add()/virtfn_remove() or
>at the points where we write PCI_SRIOV_CTRL_VFE, i.e., in sriov_init(),
>sriov_enable(), sriov_disable(), and sriov_restore_state(). From a
>hardware point of view, the VFs exist whenever PCI_SRIOV_CTRL_VFE is set,
>so it might be nice to have this setup connected to that.
If my understanding is correct, we could wrap up the configuration write/read
on PCI_SRIOV_CTRL and when it involves PCI_SRIOV_CTRL_VFE, do the fix up?
>
>Bjorn
--
Richard Yang
Help you, Help me
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
