On 09/09/2014 04:28 PM, Arnd Bergmann wrote:
On Tuesday 09 September 2014 16:17:15 Murali Karicheri wrote:
K2E SoC has two PCI ports. The SATA controller is connected to second
PCI port (port 1). This patch enhances the driver to support multiple
ports.
Update the DT Documentation for the new attribute, ti,pcie-port and
remove the note for bootargs as this is no longer needed.
Signed-off-by: Murali Karicheri<m-karicheri2@xxxxxx>
---
- updated based on comment against v1
.../devicetree/bindings/pci/pci-keystone.txt | 8 +++++---
drivers/pci/host/pci-keystone.c | 15 ++++++++++-----
drivers/pci/host/pci-keystone.h | 4 ++--
3 files changed, 17 insertions(+), 10 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt
index bedacf0..c8f5773 100644
--- a/Documentation/devicetree/bindings/pci/pci-keystone.txt
+++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt
@@ -56,11 +56,13 @@ Optional properties:-
phy-names: name of the Generic Keystine SerDes phy for PCI
- If boot loader already does PCI link establishment, then phys and
phy-names shouldn't be present.
+ ti,pcie-port: PCI port number. This is used to configure the PCI port
+ number. For example K2E SoC supports 2 PCI ports and PCI bindings
+ for the second port adds ti,pcie-port =<1> to identify second port
+ and driver uses this to configure the PCI mode register for second
+ port. If not present, port number 0 is assumed.
Is this still needed? I thought with patch 1 removed, we no longer had
a reason to know the port number.
You are right. I will remove it and re-send.
-=========================
-Driver requires pci=pcie_bus_perf in the bootargs for proper functioning.
diff --git a/drivers/pci/host/pci-keystone.c b/drivers/pci/host/pci-keystone.c
index f1119eb..893820d 100644
--- a/drivers/pci/host/pci-keystone.c
+++ b/drivers/pci/host/pci-keystone.c
@@ -253,8 +253,8 @@ static int keystone_pcie_fault(unsigned long addr, unsigned int fsr,
static void __init ks_pcie_host_init(struct pcie_port *pp)
{
- u32 vendor_device_id, val;
struct keystone_pcie *ks_pcie = to_keystone_pcie(pp);
+ u32 val;
ks_pcie_establish_link(ks_pcie);
ks_dw_pcie_setup_rc_app_regs(ks_pcie);
@@ -263,8 +263,7 @@ static void __init ks_pcie_host_init(struct pcie_port *pp)
pp->dbi_base + PCI_IO_BASE);
/* update the Vendor ID */
- vendor_device_id = readl(ks_pcie->va_reg_pciid);
- writew((vendor_device_id>> 16), pp->dbi_base + PCI_DEVICE_ID);
+ writew(ks_pcie->device_id, pp->dbi_base + PCI_DEVICE_ID);
/* update the DEV_STAT_CTRL to publish right mrrs */
val = readl(pp->dbi_base + PCIE_CAP_BASE + PCI_EXP_DEVCTL);
This change must have slipped in accidentally, at least it's not
described in the changelog. Should this be another patch?
The change seems useful.
Are you referring to mrrs or update to device id? device id is in a SoC
register at index2 and is read and updated by the driver here. MRRS
update was originally in the code.
Murali
Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html