Re: [PATCH 06/17] pci: host: pcie-designware: Use *base-mask* for configuring the iATU

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



hi Arnd,

On Tuesday 13 May 2014 07:04 PM, Arnd Bergmann wrote:
> On Tuesday 13 May 2014 15:27:46 Arnd Bergmann wrote:
>> On Tuesday 13 May 2014 18:56:23 Kishon Vijay Abraham I wrote:
>>>> If you have a case where the outbound translation is a 256MB (i.e. 28bit)
>>>> section of the CPU address space, that could be represented as
>>>>
>>>>       ranges = <0x82000000 0 0  0xb0000000  0 0x10000000>;
>>>>
>>>> or 
>>>>
>>>>       ranges = <0x82000000 0 0xb0000000  0xb0000000  0 0x10000000>;
>>>>
>>>> depending on whether you want the BARs to be programmed using a low
>>>> address 0x0-0x0fffffff or an address matching the window
>>>> 0xb0000000-0xbfffffff.
>>>
>>> The problem is, for configuring the window starting at 0xb0000000, the ATU
>>> should be programmed 0x0000000 (the cpu address for it will be 0xb0000000 though).
>>>
>>
>> Then use the first of the two?
>>
> 
> To clarify: using <0x82000000 0 0  0xb0000000  0 0x10000000> will give you 
> a mem_offset of 0xb0000000, which should work just fine for this case.
> 
> What I don't understand is why the ATU cares about whether the outbound
> address is 0x0000000 or 0xb0000000 if it just decodes the lower 28 bit
> anyway. Did you mean that we have to program the BARs using low addresses
> regardless of what is programmed in the ATU? That would make more sense,
> and it also matches what I suggested.

No, It's not like it decodes only the lower 28bits. The BARs is programmed with
32 bit value.

My pcie dt node has
 ranges = <0x00000800 0 0x20001000 0x20001000 0 0x00002000  /* CONFIG */
           0x81000000 0 0          0x20003000 0 0x00010000  /* IO */
           0x82000000 0 0x20013000 0x20013000 0 0xffed000>; /* MEM */

Consider MEM address space..

Here both PCI address and CPU address is 0x20013000. So when there is a write
to cpu addr 0x20013000 [writel(virt_addr(0x20013000)], we want it to be
translated to PCI addr 0x20013000. So in 'ATU', we would expect *base* to be
programmed to *0x20013000* and target to be programmed to *0x20013000*. But
that's not the case for DRA7xx. For DRA7xx *base* should be programmed to
*0x0013000* and target should be programmed to *0x20013000*.

Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux