On Wed, 2013-11-27 at 13:32 +0800, Mike Qiu wrote: > On 11/27/2013 04:32 AM, Rafael J. Wysocki wrote: > > On Tuesday, November 26, 2013 01:41:13 PM Mike Qiu wrote: > >> On 11/14/2013 04:54 PM, Huang Ying wrote: > >>> On Thu, 2013-11-14 at 16:37 +0800, mike wrote: > >>>> On 11/14/2013 04:25 PM, Huang Ying wrote: > >>>>> On Thu, 2013-11-14 at 16:12 +0800, mike wrote: > >>>>>> On 11/14/2013 03:53 PM, Huang Ying wrote: > >>>>>>> On Thu, 2013-11-14 at 15:19 +0800, mike wrote: > >>>>>>>> On 11/14/2013 01:59 PM, Huang Ying wrote: > >>>>>>>>> On Thu, 2013-11-14 at 11:23 +0800, mike wrote: > >>>>>>>>>> On 11/14/2013 03:20 AM, Alan Stern wrote: > >>>>>>>>>>> On Wed, 13 Nov 2013, Bjorn Helgaas wrote: > >>>>>>>>>>> > >>>>>>>>>>>> [+cc Rafael, linux-pm] > >>>>>>>>>>>> > >>>>>>>>>>>> On Wed, Nov 13, 2013 at 6:09 AM, mike<qiudayu@xxxxxxxxxxxxxxxxxx> wrote: > >>>>>>>>>>>>> Hi Huang Ying, > >>>>>>>>>>>>> > >>>>>>>>>>>>> I see you are the author of this patch, commit id is: > >>>>>>>>>>>>> 967577b062417b4e4b8e27b711220f4124f5153a > >>>>>>>>>>>>> > >>>>>>>>>>>>> I have a question while I try to understand this patch, > >>>>>>>>>>>>> So I would very grateful if you or others can give me some reply..... > >>>>>>>>>>>>> > >>>>>>>>>>>>> ............ > >>>>>>>>>>>>> - rc = ddi->drv->probe(ddi->dev, ddi->id); > >>>>>>>>>>>>> + pm_runtime_get_sync(dev); > >>>>>>>>>>>>> + pci_dev->driver = pci_drv; > >>>>>>>>>>>>> ^^^^^^^^^^^^^^^^^^^^^^^^^^ > >>>>>>>>>>>>> I see here you make the driver to initialize before probe, > >>>>>>>>>>>>> But I have no idea of why you do this change..... > >>>>>>>>>>>>> > >>>>>>>>>>>>> and I look inside the code, it may be pm_runtime relate?? > >>>>>>>>>>> Yes, it is related to runtime PM. In the PCI subsystem, runtime PM > >>>>>>>>>>> doesn't do anything unless pci_dev->driver is set. You can see this at > >>>>>>>>>>> the start of pci_pm_runtime_suspend(). > >>>>>>>>>>> > >>>>>>>>>>> Since we want the driver's probe routine to be able to carry out > >>>>>>>>>>> runtime PM operations, we have to set pci_dev->driver before the probe > >>>>>>>>>>> routine runs. > >>>>>>>>>> Is there any situations , like in probe state, pci_dev->driver > >>>>>>>>>> has been set. the pci_pm_runtime_xxx() has passed > >>>>>>>>>> pci_dev->driver NULL check, but at this point, probe fail > >>>>>>>>>> occurs, and pci_dev->driver to be set to NULL. > >>>>>>>>>> > >>>>>>>>>> What will happen ? Or this situation will never happen? > >>>>>>>>>> I'm confuse about this. > >>>>>>>>> I think that will never happen. Before ->probe(), pm_runtime_get_sync() > >>>>>>>>> is called, so pci_pm_runtime_xxx() will not be called until > >>>>>>>>> pm_runtime_put_noidle() is called in ->probe(). And > >>>>>>>>> should be done as one of the latest actions in > >>>>>>>>> ->probe(), after the normal probe actions succeeded. > >>>>>>>> OK, just as your description, it seems OK. > >>>>>>>> But this is really a issue as I explained in last email. > >>>>>>>> > >>>>>>>> So I want to know if there are any side-effect of changing the code > >>>>>>>> in pci_pm_runtime_xxx() > >>>>>>>> > >>>>>>>> if (!pci_dev->driver) > >>>>>>>> return 0; > >>>>>>>> to > >>>>>>>> > >>>>>>>> if (!dev->driver) > >>>>>>>> return 0; > >>>>>>>> > >>>>>>> If you make this change, we can not put devices into low power state > >>>>>>> (runtime suspend the device) in ->probe(). That is expected in some > >>>>>> ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > >>>>>> This means dev->driver is NULL ?? but pci_dev->driver is set??? > >>>>>> > >>>>>> Because if use pci_dev->driver can put into low power state, means > >>>>>> > >>>>>> pci_dev->driver is set, but in the situation, use dev->driver will can't, > >>>>>> > >>>>>> means dev->driver = null, but I have not find any case that > >>>>>> > >>>>>> dev->driver = null, but pci_dev->driver != null; > >>>>> Sorry I make a mistake here. The dev->driver != null in > >>>>> local_pci_probe(). We use pci_dev->driver instead of dev->driver in > >>>>> pci_pm_runtime_xxx() because we want device to be kept in normal power > >>>>> state (D0) and SUSPENDED state when unbound.The > >>>>> pm_runtime_put/get_sync in pci_device_remove/local_pci_probe will not > >>>>> change the power state of the device because of the check in > >>>>> pci_pm_runtime_xxx(). > >>>> Yes, you are right, but what am I confuse is that, why check dev->driver > >>>> in pci_pm_runtime_xxx() can't keep the device in normal power > >>>> state (D0) and SUSPENDED state when unbound. > >>>> > >>>> May be logic issue ? > >>> Because dev->driver is set before local_pci_probe() and cleared after > >>> pci_device_remove(). But we need a flag to be changed in > >>> local_pci_probe() and pci_device_remove(). > >> Hi Ying, > >> > >> I'm now face one bug, and the root cause is this logic has some problem. > >> > >> The other component calls the ops in driver during probe state, which a > >> lot of critical data struct haven't been setup yet. > >> > >> This never happen in old logic, because dev->driver is unset in probe > >> state, it can check dev->driver to see if the device diver can work. But > >> for new logic it is really a big issue. > > What is the other component and why is it doing that? > > Some component like EEH in Power arch, it need to check whether the > driver is work or not. > > In old logic, if probed then dev->driver set, otherwise it will be NULL, > it is safe to do so. > > But in new, it has problem, it can call the driver API, which is very > dangerous in probe state, maybe a lot key data structure haven't been > setup yet, this lead to the kernel down and machine reboot. Also this > can be fixed in driver, like check the driver data it self, this > solution needs all the driver fix this issue, It may be a huge program. > > So we need a new flag I think, or which old flag can we use to solve > this issue ? I think a flag is not safe for you. Driver may be removed when you operate on it. Better to use device_lock() if possible, which will be held during device probe and driver remove. Best Regards, Huang Ying > Thanks > Mike > > > > Checking dev->driver may not be a correct way to address this issue anyway. > > > > > Thanks! > > > -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
