On Tue, Oct 29, 2013 at 10:12 AM, Valentine Barshak
<valentine.barshak@xxxxxxxxxxxxxxxxxx> wrote:
> This adds internal PCI controller driver for R-Car Gen2 SoC.
> There are three PCI controllers available with only a single
> EHCI/OHCI device built-in on each PCI bus.
> This gives us three USB channels. Channel 0 is shared with
> the USBHS device, while channel 2 is shared with the USBSS.
>
> The PCI controllers do not support I/O port space mapping,
> and it is not needed here.
>
> Signed-off-by: Valentine Barshak <valentine.barshak@xxxxxxxxxxxxxxxxxx>
Applied to my pci/host-rcar branch for v3.13, thanks.
> ---
> drivers/pci/host/Kconfig | 8 +
> drivers/pci/host/Makefile | 1 +
> drivers/pci/host/pci-rcar-gen2.c | 333 +++++++++++++++++++++++++++++++++++++++
> 3 files changed, 342 insertions(+)
> create mode 100644 drivers/pci/host/pci-rcar-gen2.c
>
> diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
> index 3d95048..2e33c2b 100644
> --- a/drivers/pci/host/Kconfig
> +++ b/drivers/pci/host/Kconfig
> @@ -19,4 +19,12 @@ config PCI_TEGRA
> bool "NVIDIA Tegra PCIe controller"
> depends on ARCH_TEGRA
>
> +config PCI_RCAR_GEN2
> + bool "Renesas R-Car Gen2 Internal PCI controller"
> + depends on ARM && (ARCH_R8A7790 || ARCH_R8A7791 || COMPILE_TEST)
> + help
> + Say Y here if you want internal PCI support on R-Car Gen2 SoC.
> + There are 3 internal PCI controllers available with a single
> + built-in EHCI/OHCI host controller present on each one.
> +
> endmenu
> diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
> index c9a997b..63d9727 100644
> --- a/drivers/pci/host/Makefile
> +++ b/drivers/pci/host/Makefile
> @@ -2,3 +2,4 @@ obj-$(CONFIG_PCIE_DW) += pcie-designware.o
> obj-$(CONFIG_PCI_EXYNOS) += pci-exynos.o
> obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
> obj-$(CONFIG_PCI_TEGRA) += pci-tegra.o
> +obj-$(CONFIG_PCI_RCAR_GEN2) += pci-rcar-gen2.o
> diff --git a/drivers/pci/host/pci-rcar-gen2.c b/drivers/pci/host/pci-rcar-gen2.c
> new file mode 100644
> index 0000000..cbaa5c4
> --- /dev/null
> +++ b/drivers/pci/host/pci-rcar-gen2.c
> @@ -0,0 +1,333 @@
> +/*
> + * pci-rcar-gen2: internal PCI bus support
> + *
> + * Copyright (C) 2013 Renesas Solutions Corp.
> + * Copyright (C) 2013 Cogent Embedded, Inc.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +
> +/* AHB-PCI Bridge PCI communication registers */
> +#define RCAR_AHBPCI_PCICOM_OFFSET 0x800
> +
> +#define RCAR_PCIAHB_WIN1_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x00)
> +#define RCAR_PCIAHB_WIN2_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x04)
> +#define RCAR_PCIAHB_PREFETCH0 0x0
> +#define RCAR_PCIAHB_PREFETCH4 0x1
> +#define RCAR_PCIAHB_PREFETCH8 0x2
> +#define RCAR_PCIAHB_PREFETCH16 0x3
> +
> +#define RCAR_AHBPCI_WIN1_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x10)
> +#define RCAR_AHBPCI_WIN2_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x14)
> +#define RCAR_AHBPCI_WIN_CTR_MEM (3 << 1)
> +#define RCAR_AHBPCI_WIN_CTR_CFG (5 << 1)
> +#define RCAR_AHBPCI_WIN1_HOST (1 << 30)
> +#define RCAR_AHBPCI_WIN1_DEVICE (1 << 31)
> +
> +#define RCAR_PCI_INT_ENABLE_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x20)
> +#define RCAR_PCI_INT_STATUS_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x24)
> +#define RCAR_PCI_INT_A (1 << 16)
> +#define RCAR_PCI_INT_B (1 << 17)
> +#define RCAR_PCI_INT_PME (1 << 19)
> +
> +#define RCAR_AHB_BUS_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x30)
> +#define RCAR_AHB_BUS_MMODE_HTRANS (1 << 0)
> +#define RCAR_AHB_BUS_MMODE_BYTE_BURST (1 << 1)
> +#define RCAR_AHB_BUS_MMODE_WR_INCR (1 << 2)
> +#define RCAR_AHB_BUS_MMODE_HBUS_REQ (1 << 7)
> +#define RCAR_AHB_BUS_SMODE_READYCTR (1 << 17)
> +#define RCAR_AHB_BUS_MODE (RCAR_AHB_BUS_MMODE_HTRANS | \
> + RCAR_AHB_BUS_MMODE_BYTE_BURST | \
> + RCAR_AHB_BUS_MMODE_WR_INCR | \
> + RCAR_AHB_BUS_MMODE_HBUS_REQ | \
> + RCAR_AHB_BUS_SMODE_READYCTR)
> +
> +#define RCAR_USBCTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x34)
> +#define RCAR_USBCTR_USBH_RST (1 << 0)
> +#define RCAR_USBCTR_PCICLK_MASK (1 << 1)
> +#define RCAR_USBCTR_PLL_RST (1 << 2)
> +#define RCAR_USBCTR_DIRPD (1 << 8)
> +#define RCAR_USBCTR_PCIAHB_WIN2_EN (1 << 9)
> +#define RCAR_USBCTR_PCIAHB_WIN1_256M (0 << 10)
> +#define RCAR_USBCTR_PCIAHB_WIN1_512M (1 << 10)
> +#define RCAR_USBCTR_PCIAHB_WIN1_1G (2 << 10)
> +#define RCAR_USBCTR_PCIAHB_WIN1_2G (3 << 10)
> +#define RCAR_USBCTR_PCIAHB_WIN1_MASK (3 << 10)
> +
> +#define RCAR_PCI_ARBITER_CTR_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x40)
> +#define RCAR_PCI_ARBITER_PCIREQ0 (1 << 0)
> +#define RCAR_PCI_ARBITER_PCIREQ1 (1 << 1)
> +#define RCAR_PCI_ARBITER_PCIBP_MODE (1 << 12)
> +
> +#define RCAR_PCI_UNIT_REV_REG (RCAR_AHBPCI_PCICOM_OFFSET + 0x48)
> +
> +/* Number of internal PCI controllers */
> +#define RCAR_PCI_NR_CONTROLLERS 3
> +
> +struct rcar_pci_priv {
> + void __iomem *reg;
> + struct resource io_res;
> + struct resource mem_res;
> + struct resource *cfg_res;
> + int irq;
> +};
> +
> +/* PCI configuration space operations */
> +static void __iomem *rcar_pci_cfg_base(struct pci_bus *bus, unsigned int devfn,
> + int where)
> +{
> + struct pci_sys_data *sys = bus->sysdata;
> + struct rcar_pci_priv *priv = sys->private_data;
> + int slot, val;
> +
> + if (sys->busnr != bus->number || PCI_FUNC(devfn))
> + return NULL;
> +
> + /* Only one EHCI/OHCI device built-in */
> + slot = PCI_SLOT(devfn);
> + if (slot > 2)
> + return NULL;
> +
> + val = slot ? RCAR_AHBPCI_WIN1_DEVICE | RCAR_AHBPCI_WIN_CTR_CFG :
> + RCAR_AHBPCI_WIN1_HOST | RCAR_AHBPCI_WIN_CTR_CFG;
> +
> + iowrite32(val, priv->reg + RCAR_AHBPCI_WIN1_CTR_REG);
> + return priv->reg + (slot >> 1) * 0x100 + where;
> +}
> +
> +static int rcar_pci_read_config(struct pci_bus *bus, unsigned int devfn,
> + int where, int size, u32 *val)
> +{
> + void __iomem *reg = rcar_pci_cfg_base(bus, devfn, where);
> +
> + if (!reg)
> + return PCIBIOS_DEVICE_NOT_FOUND;
> +
> + switch (size) {
> + case 1:
> + *val = ioread8(reg);
> + break;
> + case 2:
> + *val = ioread16(reg);
> + break;
> + default:
> + *val = ioread32(reg);
> + break;
> + }
> +
> + return PCIBIOS_SUCCESSFUL;
> +}
> +
> +static int rcar_pci_write_config(struct pci_bus *bus, unsigned int devfn,
> + int where, int size, u32 val)
> +{
> + void __iomem *reg = rcar_pci_cfg_base(bus, devfn, where);
> +
> + if (!reg)
> + return PCIBIOS_DEVICE_NOT_FOUND;
> +
> + switch (size) {
> + case 1:
> + iowrite8(val, reg);
> + break;
> + case 2:
> + iowrite16(val, reg);
> + break;
> + default:
> + iowrite32(val, reg);
> + break;
> + }
> +
> + return PCIBIOS_SUCCESSFUL;
> +}
> +
> +/* PCI interrupt mapping */
> +static int __init rcar_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
> +{
> + struct pci_sys_data *sys = dev->bus->sysdata;
> + struct rcar_pci_priv *priv = sys->private_data;
> +
> + return priv->irq;
> +}
> +
> +/* PCI host controller setup */
> +static int __init rcar_pci_setup(int nr, struct pci_sys_data *sys)
> +{
> + struct rcar_pci_priv *priv = sys->private_data;
> + void __iomem *reg = priv->reg;
> + u32 val;
> +
> + val = ioread32(reg + RCAR_PCI_UNIT_REV_REG);
> + pr_info("PCI: bus%u revision %x\n", sys->busnr, val);
> +
> + /* Disable Direct Power Down State and assert reset */
> + val = ioread32(reg + RCAR_USBCTR_REG) & ~RCAR_USBCTR_DIRPD;
> + val |= RCAR_USBCTR_USBH_RST | RCAR_USBCTR_PLL_RST;
> + iowrite32(val, reg + RCAR_USBCTR_REG);
> + udelay(4);
> +
> + /* De-assert reset and set PCIAHB window1 size to 1GB */
> + val &= ~(RCAR_USBCTR_PCIAHB_WIN1_MASK | RCAR_USBCTR_PCICLK_MASK |
> + RCAR_USBCTR_USBH_RST | RCAR_USBCTR_PLL_RST);
> + iowrite32(val | RCAR_USBCTR_PCIAHB_WIN1_1G, reg + RCAR_USBCTR_REG);
> +
> + /* Configure AHB master and slave modes */
> + iowrite32(RCAR_AHB_BUS_MODE, reg + RCAR_AHB_BUS_CTR_REG);
> +
> + /* Configure PCI arbiter */
> + val = ioread32(reg + RCAR_PCI_ARBITER_CTR_REG);
> + val |= RCAR_PCI_ARBITER_PCIREQ0 | RCAR_PCI_ARBITER_PCIREQ1 |
> + RCAR_PCI_ARBITER_PCIBP_MODE;
> + iowrite32(val, reg + RCAR_PCI_ARBITER_CTR_REG);
> +
> + /* PCI-AHB mapping: 0x40000000-0x80000000 */
> + iowrite32(0x40000000 | RCAR_PCIAHB_PREFETCH16,
> + reg + RCAR_PCIAHB_WIN1_CTR_REG);
> +
> + /* AHB-PCI mapping: OHCI/EHCI registers */
> + val = priv->mem_res.start | RCAR_AHBPCI_WIN_CTR_MEM;
> + iowrite32(val, reg + RCAR_AHBPCI_WIN2_CTR_REG);
> +
> + /* Enable AHB-PCI bridge PCI configuration access */
> + iowrite32(RCAR_AHBPCI_WIN1_HOST | RCAR_AHBPCI_WIN_CTR_CFG,
> + reg + RCAR_AHBPCI_WIN1_CTR_REG);
> + /* Set PCI-AHB Window1 address */
> + iowrite32(0x40000000 | PCI_BASE_ADDRESS_MEM_PREFETCH,
> + reg + PCI_BASE_ADDRESS_1);
> + /* Set AHB-PCI bridge PCI communication area address */
> + val = priv->cfg_res->start + RCAR_AHBPCI_PCICOM_OFFSET;
> + iowrite32(val, reg + PCI_BASE_ADDRESS_0);
> +
> + val = ioread32(reg + PCI_COMMAND);
> + val |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY |
> + PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
> + iowrite32(val, reg + PCI_COMMAND);
> +
> + /* Enable PCI interrupts */
> + iowrite32(RCAR_PCI_INT_A | RCAR_PCI_INT_B | RCAR_PCI_INT_PME,
> + reg + RCAR_PCI_INT_ENABLE_REG);
> +
> + /* Add PCI resources */
> + pci_add_resource(&sys->resources, &priv->io_res);
> + pci_add_resource(&sys->resources, &priv->mem_res);
> +
> + return 1;
> +}
> +
> +static struct pci_ops rcar_pci_ops = {
> + .read = rcar_pci_read_config,
> + .write = rcar_pci_write_config,
> +};
> +
> +static struct hw_pci rcar_hw_pci __initdata = {
> + .map_irq = rcar_pci_map_irq,
> + .ops = &rcar_pci_ops,
> + .setup = rcar_pci_setup,
> +};
> +
> +static int rcar_pci_count __initdata;
> +
> +static int __init rcar_pci_add_controller(struct rcar_pci_priv *priv)
> +{
> + void **private_data;
> + int count;
> +
> + if (rcar_hw_pci.nr_controllers < rcar_pci_count)
> + goto add_priv;
> +
> + /* (Re)allocate private data pointer array if needed */
> + count = rcar_pci_count + RCAR_PCI_NR_CONTROLLERS;
> + private_data = kzalloc(count * sizeof(void *), GFP_KERNEL);
> + if (!private_data)
> + return -ENOMEM;
> +
> + rcar_pci_count = count;
> + if (rcar_hw_pci.private_data) {
> + memcpy(private_data, rcar_hw_pci.private_data,
> + rcar_hw_pci.nr_controllers * sizeof(void *));
> + kfree(rcar_hw_pci.private_data);
> + }
> +
> + rcar_hw_pci.private_data = private_data;
> +
> +add_priv:
> + /* Add private data pointer to the array */
> + rcar_hw_pci.private_data[rcar_hw_pci.nr_controllers++] = priv;
> + return 0;
> +}
> +
> +static int __init rcar_pci_probe(struct platform_device *pdev)
> +{
> + struct resource *cfg_res, *mem_res;
> + struct rcar_pci_priv *priv;
> + void __iomem *reg;
> +
> + cfg_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + reg = devm_ioremap_resource(&pdev->dev, cfg_res);
> + if (!reg)
> + return -ENODEV;
> +
> + mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + if (!mem_res || !mem_res->start)
> + return -ENODEV;
> +
> + priv = devm_kzalloc(&pdev->dev,
> + sizeof(struct rcar_pci_priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->mem_res = *mem_res;
> + /*
> + * The controller does not support/use port I/O,
> + * so setup a dummy port I/O region here.
> + */
> + priv->io_res.start = priv->mem_res.start;
> + priv->io_res.end = priv->mem_res.end;
> + priv->io_res.flags = IORESOURCE_IO;
> +
> + priv->cfg_res = cfg_res;
> +
> + priv->irq = platform_get_irq(pdev, 0);
> + priv->reg = reg;
> +
> + return rcar_pci_add_controller(priv);
> +}
> +
> +static struct platform_driver rcar_pci_driver = {
> + .driver = {
> + .name = "pci-rcar-gen2",
> + },
> +};
> +
> +static int __init rcar_pci_init(void)
> +{
> + int retval;
> +
> + retval = platform_driver_probe(&rcar_pci_driver, rcar_pci_probe);
> + if (!retval)
> + pci_common_init(&rcar_hw_pci);
> +
> + /* Private data pointer array is not needed any more */
> + kfree(rcar_hw_pci.private_data);
> + rcar_hw_pci.private_data = NULL;
> +
> + return retval;
> +}
> +
> +subsys_initcall(rcar_pci_init);
> +
> +MODULE_LICENSE("GPL v2");
> +MODULE_DESCRIPTION("Renesas R-Car Gen2 internal PCI");
> +MODULE_AUTHOR("Valentine Barshak <valentine.barshak@xxxxxxxxxxxxxxxxxx>");
> --
> 1.8.3.1
>
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
