> -----Original Message----- > From: Tim Harvey [mailto:tharvey@xxxxxxxxxxxxx] > Sent: Friday, October 18, 2013 1:33 PM > To: Sean Cross > Cc: devicetree@xxxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx; linux-arm- > kernel@xxxxxxxxxxxxxxxxxxx; Sascha Hauer; Zhu Richard-R65037; Shawn Guo; Bjorn > Helgaas; Marek Vašut; Jingoo Han; Pratyush Anand; Troy Kisky > Subject: Re: [PATCH v6 3/3] PCI: imx6: Add support for i.MX6 PCIe controller > > On Mon, Sep 16, 2013 at 1:20 AM, Sean Cross <xobs@xxxxxxxxxx> wrote: > > Add support for the PCIe port present on the i.MX6 family of controllers. > > These use the Synopsis Designware core tied to their own PHY. > > > > Signed-off-by: Sean Cross <xobs@xxxxxxxxxx> > > Acked-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx> > > --- > > .../devicetree/bindings/pci/designware-pcie.txt | 7 +- > > diff --git a/arch/arm/boot/dts/imx6qdl.dtsi > > b/arch/arm/boot/dts/imx6qdl.dtsi index ccd55c2..125202e 100644 > > --- a/arch/arm/boot/dts/imx6qdl.dtsi > > +++ b/arch/arm/boot/dts/imx6qdl.dtsi > > @@ -116,6 +116,22 @@ > > arm,data-latency = <4 2 3>; > > }; > > > > + pcie: pcie@0x01000000 { > > + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; > > + reg = <0x01ffc000 0x4000>; /* DBI */ > > + #address-cells = <3>; > > + #size-cells = <2>; > > + device_type = "pci"; > > + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 > 0x00080000 /* configuration space */ > > + 0x81000000 0 0 0x01f80000 0 > 0x00010000 /* downstream I/O */ > > + 0x82000000 0 0x01000000 0x01000000 0 > 0x00f00000>; /* non-prefetchable memory */ > > + num-lanes = <1>; > > + interrupts = <0 123 0x04>; > > + clocks = <&clks 189>, <&clks 187>, <&clks 205>, > <&clks 144>; > > + clock-names = "pcie_ref_125m", "sata_ref_100m", > "lvds_gate", "pcie_axi"; > > + status = "disabled"; > > + }; > > + > > Sean, > > The devicetree portion above is now here > https://gitorious.org/thierryreding/linux- > next/commit/3a57291fa4ca7f7647d826f5b47082ef306d839f > (which I'm told gets pulled into linux-next) and I wanted to see if you or any > of the other IMX/PCI gurus here can answer a question about region mapping. > > The above ranges look to me to allocate 15MB for mem resources, 64K for io > resources, and 256K for cfg space. > > Table 2.1 of the IMX6DQRM.pdf > (http://cache.freescale.com/files/32bit/doc/ref_manual/IMX6DQRM.pdf) > shows: > 01FF_C000 01FF_FFFF 16 KB PCIe registers > 0100_0000 01FF_BFFF 16368 KB PCIe > > The driver in the fsl 3.0.35_4.1.0 BSP maps the following (see > http://git.freescale.com/git/cgit.cgi/imx/linux-2.6- > imx.git/tree/arch/arm/mach-mx6/pcie.c?h=imx_3.0.35_4.1.0#n331): > > 0x0100_0000 --- 0x01DF_FFFF 14MB IORESOURCE_MEM > 0x01E0_0000 --- 0x01EF_FFFF 1MB IORESOURCE_IO > 0x01F0_0000 --- 0x01FF_FFFF 1MB Cfg + MSI + Registers > > and, in a discussion on the IMX Community forum > (https://community.freescale.com/message/334959#334959) points out that you > have more flexibility if you map the MEM resource first because of its more > limited alignment. So, if you were going to stick with the fsl mapping I > would think we would want something like this in the dt node: > > ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* 512K > configuration space */ > 0x81000000 0 0 0x01e00000 0 0x00100000 /* 1MB > downstream I/O */ > 0x82000000 0 0x01000000 0x01000000 0 0x00e00000>; /* 14MB non- > prefetchable memory */ > > Can these regions be moved around however you want depending on what kind of > mem vs io resource configurations you desire? How about the cfg space - is > 512K really needed? > > Are we sure the committed values to linux-next 'wrong' in any way? I still am > seeing bus-hangs with devices behind a bridge that use io-space resources and > am trying to figure out where the issue is. I don't get these bus-hangs when > using the fsl driver which is structured very different so its been difficult > for me to determine the difference. The mappings and the way iATU mappings > are done are very different. Hi Tim: Regarding to my experience, the difference shouldn't be related with the bus hang. Here are my DT region setup when I trying to bring up imx6 pcie on 3.1x kernel by my own driver. clock-names = "pcie_axi", "pcie_ref", "pcie_bus_in", "pcie_bus_out"; #address-cells = <3>; #size-cells = <2>; ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 /* configuration space */ 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ num-lanes = <1>; It works sometimes, although that there is random kernel panic and system hang(log is pasted below):( LOGS, when pericom's PI7C9X2G303EL and Intel e1000e network card is used. ... imx-pcie 1ffc000.pcie: legacy_irq 155 imx-pcie 1ffc000.pcie: map [mem 0x01ffc000-0x01ffffff] IMX PCIe port: link up. PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x1000-0x10000] pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] PCI: bus0: Fast back to back transfers disabled PCI: bus1: Fast back to back transfers disabled pci 0000:01:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus2: Fast back to back transfers disabled pci 0000:02:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:02:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring PCI: bus3: Fast back to back transfers disabled PCI: bus4: Fast back to back transfers enabled pci 0000:00:00.0: BAR 0: assigned [mem 0x01000000-0x010fffff 64bit] pci 0000:00:00.0: BAR 8: assigned [mem 0x01100000-0x012fffff] pci 0000:00:00.0: BAR 6: assigned [mem 0x01300000-0x0130ffff pref] pci 0000:00:00.0: BAR 7: assigned [io 0x1000-0x1fff] pci 0000:01:00.0: BAR 8: assigned [mem 0x01100000-0x012fffff] pci 0000:01:00.0: BAR 7: assigned [io 0x1000-0x1fff] pci 0000:02:01.0: BAR 8: assigned [mem 0x01100000-0x012fffff] pci 0000:02:01.0: BAR 7: assigned [io 0x1000-0x1fff] pci 0000:03:00.0: BAR 1: assigned [mem 0x01100000-0x011fffff] pci 0000:03:00.0: BAR 0: assigned [mem 0x01200000-0x0121ffff] pci 0000:03:00.0: BAR 3: assigned [mem 0x01220000-0x01223fff] pci 0000:03:00.0: BAR 2: assigned [io 0x1000-0x101f] pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [io 0x1000-0x1fff] pci 0000:02:01.0: bridge window [mem 0x01100000-0x012fffff] pci 0000:02:02.0: PCI bridge to [bus 04] pci 0000:01:00.0: PCI bridge to [bus 02-04] pci 0000:01:00.0: bridge window [io 0x1000-0x1fff] pci 0000:01:00.0: bridge window [mem 0x01100000-0x012fffff] pci 0000:00:00.0: PCI bridge to [bus 01-04] pci 0000:00:00.0: bridge window [io 0x1000-0x1fff] pci 0000:00:00.0: bridge window [mem 0x01100000-0x012fffff] PCI: enabling device 0000:01:00.0 (0140 -> 0143) PCI: enabling device 0000:02:01.0 (0140 -> 0143) PCI: enabling device 0000:02:02.0 (0140 -> 0143) ... e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k e1000e: Copyright(c) 1999 - 2013 Intel Corporation. e1000e 0000:03:00.0: Disabling ASPM L0s L1 PCI: enabling device 0000:03:00.0 (0140 -> 0142) e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode e1000e 0000:03:00.0 eth1: registered PHC clock e1000e 0000:03:00.0 eth1: (PCI Express:2.5GT/s:Width x1) 00:1b:21:3a:18:8b e1000e 0000:03:00.0 eth1: Intel(R) PRO/1000 Network Connection e1000e 0000:03:00.0 eth1: MAC: 3, PHY: 8, PBA No: E42641-005 igb: Intel(R) Gigabit Ethernet Network Driver - version 5.0.3-k igb: Copyright (c) 2007-2013 Intel Corporation. ... ALSA device list: #0: wm8962-audio VFS: Mounted root (nfs filesystem) on device 0:11. devtmpfs: mounted Freeing unused kernel memory: 324K (8082d000 - 8087e000) Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b <-- Kernel panic here randomly. Same phenomena when the root-fs is located in SD. CPU1: stopping CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.11.0-rc3+ #13 Backtrace: [<80011b58>] (dump_backtrace+0x0/0x10c) from [<80011cf8>] (show_stack+0x18/0x1c) r6:bf896000 r5:8087dd84 r4:00000000 r3:00000000 [<80011ce0>] (show_stack+0x0/0x1c) from [<80642d8c>] (dump_stack+0x78/0x94) [<80642d14>] (dump_stack+0x0/0x94) from [<80014a60>] (handle_IPI+0x138/0x174) > > Thanks, > > Tim Thanks. Best Regards Richard Zhu -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
