On Tue, Oct 15, 2013 at 9:06 AM, Marek Vasut <marex@xxxxxxx> wrote: > > The resource retrieval from the DT was not done right. This resulted > in bogus values in the IO/MEM window configuration. I re-used the code > implementation from pci-tegra.c to do the resource retrieval correctly. > > This in turn resulted in very strange behavior on two different kinds > of setup: > > Setup #1: ,-------> Intel i210 (igb driver) > i.MX6 root port -----> PCIe switch > `-------> Empty slot > > Setup #2: ,-------> Marvell Yukon (sky2 driver) > i.MX6 root port -----> PCIe switch > `-------> Empty slot > > Both setups expressed the same behavior. The system booted and the > ethernet controllers were properly detected. After the controllers > were configured and just after they reported "Ethernet Link Up", the > entire system froze. It is now clear this happened because the resources > were incorrectly configured, which in turn means the iATU was also not > configured correctly. > > Signed-off-by: Marek Vasut <marex@xxxxxxx> > Cc: Bjorn Helgaas <bhelgaas@xxxxxxxxxx> > Cc: Frank Li <lznuaa@xxxxxxxxx> > Cc: Jingoo Han <jg1.han@xxxxxxxxxxx> > Cc: Mohit KUMAR <Mohit.KUMAR@xxxxxx> > Cc: Pratyush Anand <pratyush.anand@xxxxxx> > Cc: Richard Zhu <r65037@xxxxxxxxxxxxx> > Cc: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx> > Cc: Sean Cross <xobs@xxxxxxxxxx> > Cc: Shawn Guo <shawn.guo@xxxxxxxxxx> > Cc: Siva Reddy Kallam <siva.kallam@xxxxxxxxxxx> > Cc: Srikanth T Shivanand <ts.srikanth@xxxxxxxxxxx> > Cc: Tim Harvey <tharvey@xxxxxxxxxxxxx> > Cc: Troy Kisky <troy.kisky@xxxxxxxxxxxxxxxxxxx> > Cc: Yinghai Lu <yinghai@xxxxxxxxxx> > --- > drivers/pci/host/pcie-designware.c | 17 ++++++----------- > 1 file changed, 6 insertions(+), 11 deletions(-) > > diff --git a/drivers/pci/host/pcie-designware.c b/drivers/pci/host/pcie-designware.c > index 5d183ae..97c5951 100644 > --- a/drivers/pci/host/pcie-designware.c > +++ b/drivers/pci/host/pcie-designware.c > @@ -370,6 +370,7 @@ int __init dw_pcie_host_init(struct pcie_port *pp) > struct device_node *np = pp->dev->of_node; > struct of_pci_range range; > struct of_pci_range_parser parser; > + struct resource res; > u32 val; > > struct irq_domain *irq_domain; > @@ -381,28 +382,22 @@ int __init dw_pcie_host_init(struct pcie_port *pp) > > /* Get the I/O and memory ranges from DT */ > for_each_of_pci_range(&parser, &range) { > - unsigned long restype = range.flags & IORESOURCE_TYPE_BITS; > + of_pci_range_to_resource(&range, np, &res); > + unsigned long restype = res.flags & IORESOURCE_TYPE_BITS; > if (restype == IORESOURCE_IO) { > - of_pci_range_to_resource(&range, np, &pp->io); > + memcpy(&pp->io, &res, sizeof(res)); > pp->io.name = "I/O"; > - pp->io.start = max_t(resource_size_t, > - PCIBIOS_MIN_IO, > - range.pci_addr + global_io_offset); > - pp->io.end = min_t(resource_size_t, > - IO_SPACE_LIMIT, > - range.pci_addr + range.size > - + global_io_offset); Nak - removing the adjustment to io.start/io.end breaks the io space mapping as the entire io-space allocation gets taken by the root complex. This causes any device that requests io space to fail to obtain it (your igb driver from Setup1 apparently doesn't use io space where my sky2 device from Setup2 above does). If I put back the adjustment to io.start/io.end above my sky2 device gets its io resource properly but still hangs the bus after a few interrupts. Are you sure you don't have other changes that you haven't posted yet that could have addressed the hang you get when you bring up your igb device? I agree that the the 'hang' we are seeing is a bus-hang caused by an improper iATU mapping, however I'm not convinced its a dts parsing issue. Tim > pp->config.io_size = resource_size(&pp->io); > pp->config.io_bus_addr = range.pci_addr; > } > if (restype == IORESOURCE_MEM) { > - of_pci_range_to_resource(&range, np, &pp->mem); > + memcpy(&pp->mem, &res, sizeof(res)); > pp->mem.name = "MEM"; > pp->config.mem_size = resource_size(&pp->mem); > pp->config.mem_bus_addr = range.pci_addr; > } > if (restype == 0) { > - of_pci_range_to_resource(&range, np, &pp->cfg); > + memcpy(&pp->cfg, &res, sizeof(res)); > pp->config.cfg0_size = resource_size(&pp->cfg)/2; > pp->config.cfg1_size = resource_size(&pp->cfg)/2; > } > -- > 1.8.4.rc3 > -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html