Hi,
On Thursday 12 September 2013 04:16 PM, Pratyush Anand wrote:
> On Thu, Sep 12, 2013 at 03:48:03PM +0530, Pratyush Anand wrote:
>> On Thu, Sep 12, 2013 at 06:07:23PM +0800, Kishon Vijay Abraham I wrote:
>>> Hi,
>>>
>>> On Thursday 12 September 2013 03:22 PM, Pratyush Anand wrote:
>>>> Hi Kishon,
>>>>
>>>> On Thu, Sep 12, 2013 at 05:43:40PM +0800, Kishon Vijay Abraham I wrote:
>>>>> Hi,
>>>>>
>>>>> On Thursday 12 September 2013 03:00 PM, Pratyush Anand wrote:
>>>>>> Hi Jingoo,
>>>>>>
>>>>>>
>>>>>> On Thu, Sep 12, 2013 at 03:15:04PM +0800, Jingoo Han wrote:
>>>>>>> On Tuesday 23 July 2013 12:30 PM, Kishon Vijay Abraham I wrote:
>>>>>>>>>> .
>>>>>>>>>> .
>>
>> [...]
>>
>>>>> when I do ifconfig eth0 up, I get *r8169 0000:01:00.0 eth0: link up.*
>>>>> But I dont receive any packets and ping also fails and the tx and rx packet
>>>>> count is also 0. Could it be related to inbound translation?
>>>>
>>>> A PCIe analyser log would tell a definite cause. Most likely either
>>>> inbound translation is not working or INTx/MSI is not working.
>>>
>>> I have enabled only legacy interrupts. Whenever I connect or disconnect
>>> ethernet cable I get link up/link down message and also the interrupt count for
>>> eth0 increases. So I'm not doubting INTx interrupts as such.
>
> Just a question, what is the MRRS of your RC? if it is 128, can you
> try with passing pci=pcie_bus_peer2peer in your bootargs.
>
> Again, analyser will help a lot in diagnosing such issues.
>
> Regards
> Pratyush
>>>
>>> btw configuring inbound translation once in dw_pcie_host_init enough is it? I
>>> mean we use the same registers for configuring outbound translation also no? So
>>> doesn't the inbound configuration gets lost?
>>
>> No, you write at the same register, but you program direction as
>> inbound. There are different resources for each viewport in inbound
>> and outbound direction.
I did inbound translation programming like
static void dw_pcie_prog_viewport_mem_inbound(struct pcie_port *pp)
{
u32 val;
void __iomem *val1;
void __iomem *dbi_base = pp->dbi_base;
/* Program viewport 0 : INBOUND : MEMORY*/
val = PCIE_ATU_REGION_INBOUND | (0 & 0xF);
dw_pcie_writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT);
val1 = ioremap(0x80000000, 0x5fffffff);
dw_pcie_writel_rc(pp, 0x80000000, dbi_base + PCIE_ATU_LOWER_BASE);
dw_pcie_writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE);
/* in_mem_size must be in power of 2 */
dw_pcie_writel_rc(pp, 0x5FFFFFFF, dbi_base + PCIE_ATU_LIMIT);
dw_pcie_writel_rc(pp, 0x80000000, dbi_base + PCIE_ATU_LOWER_TARGET);
dw_pcie_writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1);
val = PCIE_ATU_ENABLE;
dw_pcie_writel_rc(pp, val, dbi_base + PCIE_ATU_CR2);
}
I'm using Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express
Gigabit Ethernet controller (TP-LINK TG-3468) (it uses r8169 driver).
whenever I do a ifconfig ethp up, I get a non fatal error interrupt (after
Transmitter/Receiver Enable in r8169 driver).
I somehow starting to doubt the DMA address programmed in the ethernet card
which is in my RAM address range (0x80000000 to 0xBFFFFFFF). Should this
address be programmed in the BAR of the ethernet card? How should it be done?
My pcie dt data looks like this.
ranges = <0x00000800 0 0x20000000 0x20000000 0 0x00001000 /* configuration space */
0x81000000 0 0 0x20001000 0 0x00010000 /* io */
0x82000000 0 0x20011000 0x20011000 0 0x0ffef000>; /* memory */
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
