On Thursday 13 June 2013 22:22:31 Jingoo Han wrote:
> +struct pcie_port_info {
> + u32 cfg0_size;
> + u32 cfg1_size;
> + u32 io_size;
> + u32 mem_size;
> + phys_addr_t io_bus_addr;
> + phys_addr_t mem_bus_addr;
> +};
> +
> +struct pcie_port {
> + struct device *dev;
> + u8 controller;
> + u8 root_bus_nr;
> + void __iomem *dbi_base;
> + void __iomem *elbi_base;
> + void __iomem *phy_base;
> + void __iomem *purple_base;
> + phys_addr_t cfg0_base;
> + void __iomem *va_cfg0_base;
> + phys_addr_t cfg1_base;
> + void __iomem *va_cfg1_base;
> + phys_addr_t io_base;
> + phys_addr_t mem_base;
> + spinlock_t conf_lock;
> + struct resource cfg;
> + struct resource io;
> + struct resource mem;
> + struct pcie_port_info config;
> + struct clk *clk;
> + struct clk *bus_clk;
> + int irq;
> + int reset_gpio;
> +};
You mentioned that you'd use u64 for the resources here but did not.
> +
> +static void exynos_pcie_prog_viewport_cfg0(struct pcie_port *pp, u32 busdev)
> +{
> + u32 val;
> + void __iomem *dbi_base = pp->dbi_base;
> +
> + /* Program viewport 0 : OUTBOUND : CFG0 */
> + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT);
> + writel_rc(pp, (u64)pp->cfg0_base, dbi_base + PCIE_ATU_LOWER_BASE);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE);
> + writel_rc(pp, (u64)pp->cfg0_base + pp->config.cfg0_size - 1,
> + dbi_base + PCIE_ATU_LIMIT);
> + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET);
> + writel_rc(pp, PCIE_ATU_TYPE_CFG0, dbi_base + PCIE_ATU_CR1);
> + val = PCIE_ATU_ENABLE;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2);
> +}
> +
> +static void exynos_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev)
> +{
> + u32 val;
> + void __iomem *dbi_base = pp->dbi_base;
> +
> + /* Program viewport 1 : OUTBOUND : CFG1 */
> + val = PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT);
> + writel_rc(pp, PCIE_ATU_TYPE_CFG1, dbi_base + PCIE_ATU_CR1);
> + val = PCIE_ATU_ENABLE;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2);
> + writel_rc(pp, (u64)pp->cfg1_base, dbi_base + PCIE_ATU_LOWER_BASE);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE);
> + writel_rc(pp, (u64)pp->cfg1_base + pp->config.cfg1_size - 1,
> + dbi_base + PCIE_ATU_LIMIT);
> + writel_rc(pp, busdev, dbi_base + PCIE_ATU_LOWER_TARGET);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET);
> +}
And you still don't set up the UPPER halves, which was really the point
of my comment. Same thing for all the other ones.
> +static void exynos_pcie_prog_viewport_mem_inbound(struct pcie_port *pp)
> +{
> + u32 val;
> + void __iomem *dbi_base = pp->dbi_base;
> +
> + /* Program viewport 0 : INBOUND : MEM */
> + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX0;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT);
> + writel_rc(pp, PCIE_ATU_TYPE_MEM, dbi_base + PCIE_ATU_CR1);
> + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2);
> + writel_rc(pp, (u64)pp->config.mem_bus_addr,
> + dbi_base + PCIE_ATU_LOWER_BASE);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE);
> + writel_rc(pp, (u64)pp->config.mem_bus_addr + pp->config.mem_size - 1,
> + dbi_base + PCIE_ATU_LIMIT);
> + writel_rc(pp, (u64)pp->mem_base, dbi_base + PCIE_ATU_LOWER_TARGET);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET);
> +}
This makes even less sense than before, it seems like now you only
allow DMA between PCI devices but not to main memory.
> +static void exynos_pcie_prog_viewport_io_inbound(struct pcie_port *pp)
> +{
> + u32 val;
> + void __iomem *dbi_base = pp->dbi_base;
> +
> + /* Program viewport 1 : INBOUND : IO */
> + val = PCIE_ATU_REGION_INBOUND | PCIE_ATU_REGION_INDEX1;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT);
> + writel_rc(pp, PCIE_ATU_TYPE_IO, dbi_base + PCIE_ATU_CR1);
> + val = PCIE_ATU_ENABLE | PCIE_ATU_BAR_MODE_ENABLE;
> + writel_rc(pp, val, dbi_base + PCIE_ATU_CR2);
> + writel_rc(pp, (u64)pp->config.io_bus_addr,
> + dbi_base + PCIE_ATU_LOWER_BASE);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE);
> + writel_rc(pp, (u64)pp->config.io_bus_addr + pp->config.io_size - 1,
> + dbi_base + PCIE_ATU_LIMIT);
> + writel_rc(pp, (u64)pp->io_base, dbi_base + PCIE_ATU_LOWER_TARGET);
> + writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET);
> +}
Can you please explain what the inbound window is as I asked you?
I still don't see why you would need to set it up like this.
> +static int exynos_pcie_setup(int nr, struct pci_sys_data *sys)
> +{
> + struct pcie_port *pp;
> +
> + pp = sys_to_pcie(sys);
> +
> + if (!pp)
> + return 0;
> +
> + pci_add_resource(&sys->resources, &pp->io);
> + pci_add_resource(&sys->resources, &pp->mem);
Now you are missing the offsets. You have to at least pass an offset for one
of the I/O spaces, since they are using the same bus address. The offset must
match the value you pass to pci_ioremap_io.
For the memory space, you should pass the difference between the physical
base address and the bus address. That address happens to be zero with
you DT setup, but I would advise to also try out some other values in DT,
just to ensure it still works.
> + pp->reset_gpio = of_get_named_gpio(np, "reset-gpio", 0);
Ok.
> +
> +static int __exit exynos_pcie_remove(struct platform_device *pdev)
> +{
> + struct pcie_port *pp = platform_get_drvdata(pdev);
> +
> + clk_disable_unprepare(pp->bus_clk);
> + clk_disable_unprepare(pp->clk);
> +
> + return 0;
> +}
You also don't remove the PCI devices here, as mentioned in an earlier
review.
Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
