On Thu, May 23, 2013 at 02:22:58PM -0600, Bjorn Helgaas wrote: > On Sat, May 18, 2013 at 8:24 PM, Kevin Hao <haokexin@xxxxxxxxx> wrote: > > On Fri, May 17, 2013 at 10:51:20PM +0800, Liu Jiang wrote: > >> On Fri 17 May 2013 10:11:29 AM CST, Kevin Hao wrote: > >> >On Fri, May 17, 2013 at 12:18:07AM +0800, Liu Jiang wrote: > >> >>On Tue 14 May 2013 09:07:56 PM CST, Kevin Hao wrote: > >> >>>In the current kernel, we just set the CPU address to the bus address > >> >>>if we can't find the match region for one specific bus address. If BAR > >> >>>of one pci device is set to address which happens to be a legitimate > >> >>>CPU address by firmware, the kernel will think this resource is legal > >> >>>and will not try to reassign later. In cases the CPU address and bus > >> >>>address isn't equal, the device will not work. So we should check > >> >>>if we can translate the bus address to CPU address correctly. If not, > >> >>>we should unset this resource and wish the kernel will reassign it > >> >>>later. > >> >>> > >> >>>Since we will invoke pcibios_bus_to_resource unconditionally if we > >> >>>don't goto fail, move it out of if/else wrap. > >> >>> > >> >>>Signed-off-by: Kevin Hao <haokexin@xxxxxxxxx> > >> >>>--- > >> >>> drivers/pci/probe.c | 9 ++++++--- > >> >>> 1 file changed, 6 insertions(+), 3 deletions(-) > >> >>> > >> >>>diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c > >> >>>index 70f10fa..c96772f 100644 > >> >>>--- a/drivers/pci/probe.c > >> >>>+++ b/drivers/pci/probe.c > >> >>>@@ -250,12 +250,10 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, > >> >>> pci_write_config_dword(dev, pos + 4, 0); > >> >>> region.start = 0; > >> >>> region.end = sz64; > >> >>>- pcibios_bus_to_resource(dev, res, ®ion); > >> >>> bar_disabled = true; > >> >>> } else { > >> >>> region.start = l64; > >> >>> region.end = l64 + sz64; > >> >>>- pcibios_bus_to_resource(dev, res, ®ion); > >> >>> } > >> >>> } else { > >> >>> sz = pci_size(l, sz, mask); > >> >>>@@ -265,7 +263,12 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type, > >> >>> > >> >>> region.start = l; > >> >>> region.end = l + sz; > >> >>>- pcibios_bus_to_resource(dev, res, ®ion); > >> >>>+ } > >> >>>+ > >> >>>+ if (!pcibios_bus_to_resource(dev, res, ®ion)) { > >> >>>+ res->flags |= IORESOURCE_UNSET; > >> >>>+ res->end -= res->start; > >> >>>+ res->start = 0; > >> >>> } > >> >>> > >> >>> goto out; > >> >> > >> >>Hi Kevin, > >> >> Will this break subtractive decode PCI bridges and devices? > >> > > >> >No. A subtractive decode occurs only when no other pci bridge or device > >> >claim the transactions. As you can see that when we are trying to translate > >> >a bus address to cpu address we search the address regions of pci host > >> >bridge instead of a pci bridge. The pci host bridge address regions should > >> >cover all the bus address we can use for the pci device or bridge under this > >> >pci controller. This definitely also include the bus address regions used by > >> >the expansion bus for subtractive decode. So if a pci device use a bus address > >> >that is unknown to this pci host bridge, there is definitely something wrong > >> >here. This is the case we are trying to fix. > >> > > >> Hi Kevin, > >> I'm not sure about this assumption "the pci host bridge > >> address regions should cover > >> all the bus address we can use for the pci device or bridge under > >> this pci controller". > >> I have a fear that it may cause regressions to some legacy x86 > >> platforms, such as an AMD > >> platform with PCI based IOAPICs, though I have no evidences for it. > > > > Does any x86 expert can confirm whether the assumption that "the pci host > > bridge address regions should cover all the bus address we can use for the > > pci device or bridge under this pci host bridge" is true or not on x86? > > It seems definitely wrong in logical. But things always happen out of > > expectation in reality. :-) > > You're changing generic code, not x86-specific code, so you need the > assumption to hold on all architectures. Indeed. > I don't know off-hand > whether it's true or not. I think it should be true in general. If some architecture or platform does break this assumption, we should fix it in architecture or platform level, just as what you did for bug 31602. > > Can you save me some time by collecting a full dmesg showing the > problem, and maybe one with your fix? I attached the full kernel and lspci log for the current kernel and the one applied my fix. > I know there are cases where we > notice a BAR assignment that we think is incorrect, e.g., > https://bugzilla.kernel.org/show_bug.cgi?id=31602 (fixed by > eb31aae8cb5) and we reassign it, and I want to know how your case is > different from that. The bug 31602 is that the bios doesn't report the memory region claimed by the pci host controller correctly. In my case, the bootloader assign a wrong bus address to the pci device and this bus address happens to be a legal memory address for the kernel. In the current implementation of pcibios_bus_to_resource, it can't detect this illegal bus address and just use it as the memory address. So the pci subsystem doesn't reassign the resource for this pci device and leave a illegal bus address set in this pci device BAR, it definitely causes this device not work. The bootloader assigned the following bus address to device 0000:01:00.0: Region 0: bus address at a0000000 (64-bit, non-prefetchable) [size=128] In the current kernel, the pci host bridge use the following address regions: pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff] (bus address [0xe0000000-0xffffffff]) And no reassign for device 0000:01:00.0. With my fix, the device 0000:01:00.0 is reassigned with the correct bus address: pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff] (bus address [0xe0000000-0xffffffff]) pci 0000:01:00.0: BAR 6: assigned [mem 0xa0000000-0xa007ffff pref] pci 0000:01:00.0: BAR 2: assigned [mem 0xa0080000-0xa0083fff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0xa0084000-0xa008407f 64bit] As you can see in the current kernel the pci subsystem doesn't detect this wrong bus address and don't try a reassign what it should do. My patches is trying to fix this issue. Thanks, Kevin > > Bjorn
Using P2020RDB-PC machine description Memory CAM mapping: 256/256/256 Mb, residual: 256Mb Linux version 3.10.0-rc2-00088-g6ae7b7f (kevin@pek-khao-d1) (gcc version 4.6.3 (Wind River Linux Sourcery CodeBench 4.6a-99) ) #101 SMP Fri May 24 10:00:45 CST 2013 Found legacy serial port 0 for /soc@ffe00000/serial@4500 mem=ffe04500, taddr=ffe04500, irq=0, clk=600000000, speed=0 Found legacy serial port 1 for /soc@ffe00000/serial@4600 mem=ffe04600, taddr=ffe04600, irq=0, clk=600000000, speed=0 CPU maps initialized for 1 thread per core (thread shift is 0) bootconsole [udbg0] enabled mpc85xx_rdb_setup_arch: Could not find Quicc Engine node MPC85xx RDB board from Freescale Semiconductor Top of RAM: 0x40000000, Total RAM: 0x40000000 Memory hole size: 0MB Zone ranges: DMA [mem 0x00000000-0x2fffffff] Normal empty HighMem [mem 0x30000000-0x3fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x3fffffff] On node 0 totalpages: 262144 free_area_init_node: node 0, pgdat c07965e0, node_mem_map c0816000 DMA zone: 1536 pages used for memmap DMA zone: 0 pages reserved DMA zone: 196608 pages, LIFO batch:31 HighMem zone: 512 pages used for memmap HighMem zone: 65536 pages, LIFO batch:15 MMU: Allocated 1088 bytes of context maps for 255 contexts PERCPU: Embedded 7 pages/cpu @c101d000 s6752 r8192 d13728 u32768 pcpu-alloc: s6752 r8192 d13728 u32768 alloc=8*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 Kernel command line: root=/dev/nfs rw nfsroot=128.224.178.20:/export/pxeboot/vlm-boards/21080/rootfs ip=128.224.178.28:128.224.178.20:128.224.178.1:255.255.254.0:unknown:eth2:off console=ttyS0,115200 enforcing=0 PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Sorting __ex_table... High memory: 262140k Memory: 965152k/1048576k available (7540k kernel code, 83424k reserved, 300k data, 429k bss, 264k init) Kernel virtual memory layout: * 0xfff5f000..0xfffff000 : fixmap * 0xffc00000..0xffe00000 : highmem PTEs * 0xffbfd000..0xffc00000 : early ioremap * 0xf1000000..0xffbfd000 : vmalloc & ioremap SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. NR_IRQS:512 nr_irqs:512 16 mpic: Resetting mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs mpic: ISU size: 256, shift: 8, mask: ff mpic: Initializing for 256 sources mpc85xx_rdb_pic_init: Could not find qe-ic node time_init: decrementer frequency = 75.000000 MHz time_init: processor frequency = 1200.000000 MHz clocksource: timebase mult[d555555] shift[24] registered clockevent: decrementer mult[13333333] shift[32] cpu[0] Console: colour dummy device 80x25 pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 mpic: requesting IPIs... Brought up 2 CPUs devtmpfs: initialized NET: Registered protocol family 16 Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1 PCI host bridge /pcie@ffe09000 (primary) ranges: MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000e0000000 IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000 /pcie@ffe09000: PCICSRBAR @ 0xdff00000 Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0 PCI host bridge /pcie@ffe0a000 ranges: MEM 0x0000000080000000..0x000000009fffffff -> 0x00000000e0000000 IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000 /pcie@ffe0a000: PCICSRBAR @ 0xdff00000 PCI: Probing PCI hardware PCI: Memory resource 0 not set for host bridge /pcie@ffe09000 (domain 0) PCI: Memory resource 0 not set for host bridge /pcie@ffe09000 (domain 0) fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x0000-0xffff] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff] (bus address [0xe0000000-0xffffffff]) pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff pci 0000:00:00.0: [1957:0070] type 01 class 0x0b2000 pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01) pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:00.0: [1095:3132] type 00 class 0x018000 pci 0000:01:00.0: reg 10: [mem 0xa0000000-0xa000007f 64bit] pci 0000:01:00.0: reg 18: [mem 0xa0004000-0xa0007fff 64bit] pci 0000:01:00.0: reg 20: [io 0x1000-0x107f] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0007ffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:00:00.0: PCI bridge to [bus 01-ff] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xa00fffff] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 PCI: Memory resource 0 not set for host bridge /pcie@ffe0a000 (domain 1) PCI: Memory resource 0 not set for host bridge /pcie@ffe0a000 (domain 1) fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02 pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff]) pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff] (bus address [0xe0000000-0xffffffff]) pci_bus 0001:02: root bus resource [bus 02-ff] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to ff pci 0001:02:00.0: [1957:0070] type 01 class 0x0b2000 pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01) pci 0001:02:00.0: supports D1 D2 pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0001:02:00.0: PCI bridge to [bus 03-ff] pci 0001:02:00.0: bridge window [io 0x20000-0x20fff] pci 0001:02:00.0: bridge window [mem 0x00000000-0x000fffff] pci 0001:02:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03 pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 03 PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff] PCI 0001:02 Cannot reserve Legacy IO [io 0x20000-0x20fff] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000) pci 0000:01:00.0: BAR 6: assigned [mem 0xa0080000-0xa00fffff pref] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [io 0x0000-0xffff] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff] pci 0001:02:00.0: PCI bridge to [bus 03] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff] pci 0001:02:00.0: bridge window [mem 0x80000000-0x9fffffff] Some PCI device resources are unassigned, try booting with pci=realloc pci 0000:00:00.0: enabling device (0106 -> 0107) pci 0001:02:00.0: enabling device (0106 -> 0107) pci_bus 0000:00: resource 4 [io 0x0000-0xffff] pci_bus 0000:00: resource 5 [mem 0xa0000000-0xbfffffff] pci_bus 0000:01: resource 0 [io 0x0000-0xffff] pci_bus 0000:01: resource 1 [mem 0xa0000000-0xbfffffff] pci_bus 0001:02: resource 4 [io 0x20000-0x2ffff] pci_bus 0001:02: resource 5 [mem 0x80000000-0x9fffffff] pci_bus 0001:03: resource 0 [io 0x20000-0x2ffff] pci_bus 0001:03: resource 1 [mem 0x80000000-0x9fffffff] Setting up Freescale MSI support Registering qe_ic with sysfs... bio: create slab <bio-0> at 0 Freescale Elo / Elo Plus DMA driver fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76 fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77 fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78 fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79 fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20 fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21 fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22 fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23 vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx> PTP clock support registered EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. Switching to clocksource timebase NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP: reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 32 bytes, default 32 audit: initializing netlink socket (disabled) type=2000 audit(0.304:1): initialized bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages HugeTLB registered 16 MB page size, pre-allocated 0 pages HugeTLB registered 64 MB page size, pre-allocated 0 pages HugeTLB registered 256 MB page size, pre-allocated 0 pages HugeTLB registered 1 GB page size, pre-allocated 0 pages NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). NTFS driver 2.1.30 [Flags: R/O]. jffs2: version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. msgmni has been set to 1501 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Freescale Display Interface Unit (DIU) framebuffer driver Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A console [ttyS0] enabled, bootconsole disabled serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A Generic non-volatile memory driver v1.1 brd: module loaded loop: module loaded nbd: registered device at major 43 st: Version 20101219, fixed bufsize 32768, s/g segs 256 ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101 Amd/Fujitsu Extended Query Table at 0x0040 Amd/Fujitsu Extended Query version 1.3. number of CFI chips: 1 5 ofpart partitions found on MTD device ef000000.nor Creating 5 MTD partitions on "ef000000.nor": 0x000000000000-0x000000040000 : "NOR Vitesse-7385 Firmware" ftl_cs: FTL header not found. 0x000000040000-0x000000080000 : "NOR DTB Image" ftl_cs: FTL header not found. 0x000000080000-0x000000400000 : "NOR Linux Kernel Image" ftl_cs: FTL header not found. 0x000000400000-0x000000f00000 : "NOR JFFS2 Root File System" ftl_cs: FTL header not found. 0x000000f00000-0x000001000000 : "NOR U-Boot Image" ftl_cs: FTL header not found. NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit), 32MiB, page size: 512, OOB size: 16 Bad block table found at page 65504, version 0x01 Bad block table found at page 65472, version 0x01 6 ofpart partitions found on MTD device ff800000.flash Creating 6 MTD partitions on "ff800000.flash": 0x000000000000-0x000000100000 : "NAND U-Boot Image" ftl_cs: FTL header not found. 0x000000100000-0x000000200000 : "NAND DTB Image" ftl_cs: FTL header not found. 0x000000200000-0x000000600000 : "NAND Linux Kernel Image" ftl_cs: FTL header not found. 0x000000600000-0x000000a00000 : "NAND Compressed RFS Image" ftl_cs: FTL header not found. 0x000000a00000-0x000001100000 : "NAND JFFS2 Root File System" ftl_cs: FTL header not found. 0x000001100000-0x000002000000 : "NAND Writable User area" ftl_cs: FTL header not found. eLBC NAND device at 0xff800000, bank 1 fsl_espi ffe07000.spi: master is unqueued, this is deprecated m25p80 spi32766.0: found s25fl129p1, expected m25p80 m25p80 spi32766.0: s25fl129p1 (16384 Kbytes) 5 ofpart partitions found on MTD device spi32766.0 Creating 5 MTD partitions on "spi32766.0": 0x000000000000-0x000000080000 : "SPI U-Boot Image" ftl_cs: FTL header not found. 0x000000080000-0x000000100000 : "SPI DTB Image" ftl_cs: FTL header not found. 0x000000100000-0x000000500000 : "SPI Linux Kernel Image" ftl_cs: FTL header not found. 0x000000500000-0x000000900000 : "SPI Compressed RFS Image" ftl_cs: FTL header not found. 0x000000900000-0x000001000000 : "SPI JFFS2 RFS" ftl_cs: FTL header not found. fsl_espi ffe07000.spi: at 0xf10c0000 (irq = 59) libphy: Fixed MDIO Bus: probed libphy: Freescale PowerQUICC MII Bus: probed libphy: Freescale PowerQUICC MII Bus: probed fsl-gianfar ffe24000.ethernet eth0: mac: 00:04:9f:02:7f:3c fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256 fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256 fsl-gianfar ffe25000.ethernet eth1: mac: 00:04:9f:02:7f:3b fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256 fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256 fsl-gianfar ffe26000.ethernet eth2: mac: 00:04:9f:02:7f:3a fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256 fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256 pps pps0: new PPS source ptp0 ucc_geth_driver: QE UCC Gigabit Ethernet Controller ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage i2c /dev entries driver mpc-i2c ffe03000.i2c: timeout 1000000 us mpc-i2c ffe03100.i2c: timeout 1000000 us sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA talitos ffe30000.crypto: hwrng talitos ffe30000.crypto: fsl,sec3.1 algorithms registered in /proc/crypto usbcore: registered new interface driver usbhid usbhid: USB HID core driver snd-soc-p1022ds: missing/invalid global utils node ipip: IPv4 over IPv4 tunneling driver TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Key type dns_resolver registered /home/kevin/git/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) snd-soc-p1022rdk: missing/invalid global utils node IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready mmc0: new high speed SDHC card at address e624 mmcblk0: mmc0:e624 SU04G 3.69 GiB mmcblk0: p1 usb 1-1: new high-speed USB device number 2 using fsl-ehci hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usb 1-1.3: new high-speed USB device number 3 using fsl-ehci usb-storage 1-1.3:1.0: USB Mass Storage device detected scsi0 : usb-storage 1-1.3:1.0 scsi 0:0:0:0: Direct-Access freescale PMAP PQ: 0 ANSI: 0 CCS sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 sd 0:0:0:0: [sda] No Caching mode page present sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] No Caching mode page present sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda4 sd 0:0:0:0: [sda] No Caching mode page present sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Attached SCSI removable disk libphy: mdio@ffe24520:01 - Link is Up - 1000/Full IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready IP-Config: Complete: device=eth2, hwaddr=00:04:9f:02:7f:3a, ipaddr=128.224.178.28, mask=255.255.254.0, gw=128.224.178.1 host=unknown, domain=, nis-domain=(none) bootserver=128.224.178.20, rootserver=128.224.178.20, rootpath= ALSA device list: No soundcards found. VFS: Mounted root (nfs filesystem) on device 0:17. Freeing unused kernel memory: 264K (c071b000 - c075d000) block nbd2: Attempted send on closed socket block nbd8: Attempted send on closed socket end_request: I/O error, dev nbd8, sector 2 EXT3-fs (nbd8): error: unable to read superblock end_request: I/O error, dev nbd2, sector 2 EXT3-fs (nbd2): error: unable to read superblock block nbd8: Attempted send on closed socket end_request: I/O error, dev nbd8, sector 2 EXT2-fs (nbd8): error: unable to read superblock block nbd8: Attempted send on closed socket end_request: I/O error, dev nbd8, sector 0 FAT-fs (nbd8): unable to read boot sector block nbd15: Attempted send on closed socket end_request: I/O error, dev nbd15, sector 2 EXT3-fs (nbd15): error: unable to read superblock block nbd2: Attempted send on closed socket end_request: I/O error, dev nbd2, sector 2 EXT2-fs (nbd2): error: unable to read superblock block nbd15: Attempted send on closed socket end_request: I/O error, dev nbd15, sector 2 EXT2-fs (nbd15): error: unable to read superblock block nbd15: Attempted send on closed socket end_request: I/O error, dev nbd15, sector 0 FAT-fs (nbd15): unable to read boot sector block nbd2: Attempted send on closed socket end_request: I/O error, dev nbd2, sector 0 FAT-fs (nbd2): unable to read boot sector block nbd0: Attempted send on closed socket end_request: I/O error, dev nbd0, sector 2 EXT3-fs (nbd0): error: unable to read superblock block nbd0: Attempted send on closed socket EXT2-fs (nbd0): error: unable to read superblock block nbd5: Attempted send on closed socket EXT3-fs (nbd5): error: unable to read superblock block nbd5: Attempted send on closed socket EXT2-fs (nbd5): error: unable to read superblock block nbd0: Attempted send on closed socket FAT-fs (nbd0): unable to read boot sector block nbd5: Attempted send on closed socket FAT-fs (nbd5): unable to read boot sector block nbd14: Attempted send on closed socket EXT3-fs (nbd14): error: unable to read superblock block nbd6: Attempted send on closed socket EXT3-fs (nbd6): error: unable to read superblock block nbd12: Attempted send on closed socket EXT3-fs (nbd12): error: unable to read superblock block nbd6: Attempted send on closed socket EXT2-fs (nbd6): error: unable to read superblock block nbd14: Attempted send on closed socket EXT2-fs (nbd14): error: unable to read superblock block nbd14: Attempted send on closed socket FAT-fs (nbd14): unable to read boot sector block nbd13: Attempted send on closed socket EXT3-fs (nbd13): error: unable to read superblock block nbd7: Attempted send on closed socket block nbd13: Attempted send on closed socket EXT2-fs (nbd13): error: unable to read superblock EXT3-fs (nbd7): error: unable to read superblock block nbd1: Attempted send on closed socket block nbd13: Attempted send on closed socket FAT-fs (nbd13): unable to read boot sector EXT3-fs (nbd1): error: unable to read superblock block nbd6: Attempted send on closed socket FAT-fs (nbd6): unable to read boot sector block nbd10: Attempted send on closed socket block nbd11: Attempted send on closed socket EXT3-fs (nbd11): error: unable to read superblock EXT3-fs (nbd10): error: unable to read superblock block nbd7: Attempted send on closed socket EXT2-fs (nbd7): error: unable to read superblock block nbd12: Attempted send on closed socket block nbd11: Attempted send on closed socket EXT2-fs (nbd11): error: unable to read superblock EXT2-fs (nbd12): error: unable to read superblock block nbd11: Attempted send on closed socket FAT-fs (nbd11): unable to read boot sector block nbd9: Attempted send on closed socket EXT3-fs (nbd9): error: unable to read superblock block nbd12: Attempted send on closed socket FAT-fs (nbd12): unable to read boot sector block nbd1: Attempted send on closed socket EXT2-fs (nbd1): error: unable to read superblock block nbd10: Attempted send on closed socket EXT2-fs (nbd10): error: unable to read superblock block nbd3: Attempted send on closed socket EXT3-fs (nbd3): error: unable to read superblock block nbd9: Attempted send on closed socket EXT2-fs (nbd9): error: unable to read superblock block nbd7: Attempted send on closed socket FAT-fs (nbd7): unable to read boot sector block nbd4: Attempted send on closed socket EXT3-fs (nbd4): error: unable to read superblock block nbd4: Attempted send on closed socket EXT2-fs (nbd4): error: unable to read superblock block nbd3: Attempted send on closed socket EXT2-fs (nbd3): error: unable to read superblock block nbd9: Attempted send on closed socket FAT-fs (nbd9): unable to read boot sector block nbd3: Attempted send on closed socket FAT-fs (nbd3): unable to read boot sector block nbd10: Attempted send on closed socket FAT-fs (nbd10): unable to read boot sector block nbd4: Attempted send on closed socket FAT-fs (nbd4): unable to read boot sector block nbd1: Attempted send on closed socket FAT-fs (nbd1): unable to read boot sector EXT3-fs (mmcblk0): error: can't find ext3 filesystem on dev mmcblk0. EXT2-fs (mmcblk0): error: can't find an ext2 filesystem on dev mmcblk0. FAT-fs (mmcblk0): bogus number of reserved sectors FAT-fs (mmcblk0): Can't find a valid FAT filesystem cramfs: wrong magic NTFS-fs error (device mmcblk0): read_ntfs_boot_sector(): Primary boot sector is invalid. NTFS-fs error (device mmcblk0): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover. NTFS-fs error (device mmcblk0): ntfs_fill_super(): Not an NTFS volume. FAT-fs (sda): Invalid FSINFO signature: 0x00000000, 0x00000000 (sector = 1) FAT-fs (sda): codepage cp437 not found EXT2-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended EXT2-fs (sda4): warning: mounting unchecked fs, running e2fsck is recommended root@unknown:~# lspci -vvv 0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P2020E (rev 21) (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Region 0: Memory at <ignored> (32-bit, non-prefetchable) Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: e0000000-ffffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [4c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <2us, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- 0000:01:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01) Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 24 Region 0: Memory at a0000000 (64-bit, non-prefetchable) [size=128] Region 2: Memory at a0004000 (64-bit, non-prefetchable) [size=16K] Region 4: I/O ports at 1000 [size=128] [virtual] Expansion ROM at a0080000 [disabled] [size=512K] Capabilities: [54] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- 0001:02:00.0 PCI bridge: Freescale Semiconductor Inc P2020E (rev 21) (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at <ignored> (32-bit, non-prefetchable) Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: e0000000-ffffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [4c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <2us, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Using P2020RDB-PC machine description Memory CAM mapping: 256/256/256 Mb, residual: 256Mb Linux version 3.10.0-rc2-00090-g7120175 (kevin@pek-khao-d1) (gcc version 4.6.3 (Wind River Linux Sourcery CodeBench 4.6a-99) ) #102 SMP Fri May 24 10:13:04 CST 2013 Found legacy serial port 0 for /soc@ffe00000/serial@4500 mem=ffe04500, taddr=ffe04500, irq=0, clk=600000000, speed=0 Found legacy serial port 1 for /soc@ffe00000/serial@4600 mem=ffe04600, taddr=ffe04600, irq=0, clk=600000000, speed=0 CPU maps initialized for 1 thread per core (thread shift is 0) bootconsole [udbg0] enabled mpc85xx_rdb_setup_arch: Could not find Quicc Engine node MPC85xx RDB board from Freescale Semiconductor Top of RAM: 0x40000000, Total RAM: 0x40000000 Memory hole size: 0MB Zone ranges: DMA [mem 0x00000000-0x2fffffff] Normal empty HighMem [mem 0x30000000-0x3fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x3fffffff] On node 0 totalpages: 262144 free_area_init_node: node 0, pgdat c0798800, node_mem_map c0818000 DMA zone: 1536 pages used for memmap DMA zone: 0 pages reserved DMA zone: 196608 pages, LIFO batch:31 HighMem zone: 512 pages used for memmap HighMem zone: 65536 pages, LIFO batch:15 MMU: Allocated 1088 bytes of context maps for 255 contexts PERCPU: Embedded 7 pages/cpu @c101f000 s6752 r8192 d13728 u32768 pcpu-alloc: s6752 r8192 d13728 u32768 alloc=8*4096 pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260608 Kernel command line: root=/dev/nfs rw nfsroot=128.224.178.20:/export/pxeboot/vlm-boards/21080/rootfs ip=128.224.178.28:128.224.178.20:128.224.178.1:255.255.254.0:unknown:eth2:off console=ttyS0,115200 enforcing=0 PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Sorting __ex_table... High memory: 262140k Memory: 965144k/1048576k available (7548k kernel code, 83432k reserved, 300k data, 429k bss, 264k init) Kernel virtual memory layout: * 0xfff5f000..0xfffff000 : fixmap * 0xffc00000..0xffe00000 : highmem PTEs * 0xffbfd000..0xffc00000 : early ioremap * 0xf1000000..0xffbfd000 : vmalloc & ioremap SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2. NR_IRQS:512 nr_irqs:512 16 mpic: Resetting mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs mpic: ISU size: 256, shift: 8, mask: ff mpic: Initializing for 256 sources mpc85xx_rdb_pic_init: Could not find qe-ic node time_init: decrementer frequency = 75.000000 MHz time_init: processor frequency = 1200.000000 MHz clocksource: timebase mult[d555555] shift[24] registered clockevent: decrementer mult[13333333] shift[32] cpu[0] Console: colour dummy device 80x25 pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 mpic: requesting IPIs... Brought up 2 CPUs devtmpfs: initialized NET: Registered protocol family 16 Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->1 PCI host bridge /pcie@ffe09000 (primary) ranges: MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000e0000000 IO 0x00000000ffc10000..0x00000000ffc1ffff -> 0x0000000000000000 /pcie@ffe09000: PCICSRBAR @ 0xdff00000 Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0 PCI host bridge /pcie@ffe0a000 ranges: MEM 0x0000000080000000..0x000000009fffffff -> 0x00000000e0000000 IO 0x00000000ffc00000..0x00000000ffc0ffff -> 0x0000000000000000 /pcie@ffe0a000: PCICSRBAR @ 0xdff00000 PCI: Probing PCI hardware PCI: Memory resource 0 not set for host bridge /pcie@ffe09000 (domain 0) PCI: Memory resource 0 not set for host bridge /pcie@ffe09000 (domain 0) fsl-pci ffe09000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x0000-0xffff] pci_bus 0000:00: root bus resource [mem 0xa0000000-0xbfffffff] (bus address [0xe0000000-0xffffffff]) pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff pci 0000:00:00.0: [1957:0070] type 01 class 0x0b2000 pci 0000:00:00.0: ignoring class 0x0b2000 (doesn't match header type 01) pci 0000:00:00.0: supports D1 D2 pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:01:00.0: [1095:3132] type 00 class 0x018000 pci 0000:01:00.0: reg 10: [mem 0x00000000-0x0000007f 64bit] pci 0000:01:00.0: reg 18: [mem 0x00000000-0x00003fff 64bit] pci 0000:01:00.0: reg 20: [io 0x1000-0x107f] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0007ffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:00:00.0: PCI bridge to [bus 01-ff] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xa00fffff] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 PCI: Memory resource 0 not set for host bridge /pcie@ffe0a000 (domain 1) PCI: Memory resource 0 not set for host bridge /pcie@ffe0a000 (domain 1) fsl-pci ffe0a000.pcie: PCI host bridge to bus 0001:02 pci_bus 0001:02: root bus resource [io 0x20000-0x2ffff] (bus address [0x0000-0xffff]) pci_bus 0001:02: root bus resource [mem 0x80000000-0x9fffffff] (bus address [0xe0000000-0xffffffff]) pci_bus 0001:02: root bus resource [bus 02-ff] pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to ff pci 0001:02:00.0: [1957:0070] type 01 class 0x0b2000 pci 0001:02:00.0: ignoring class 0x0b2000 (doesn't match header type 01) pci 0001:02:00.0: supports D1 D2 pci 0001:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0001:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0001:02:00.0: PCI bridge to [bus 03-ff] pci 0001:02:00.0: bridge window [io 0x20000-0x20fff] pci 0001:02:00.0: bridge window [mem 0x00000000-0x000fffff] pci 0001:02:00.0: bridge window [mem 0x00000000-0x000fffff 64bit pref] pci_bus 0001:03: busn_res: [bus 03-ff] end is updated to 03 pci_bus 0001:02: busn_res: [bus 02-ff] end is updated to 03 PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff] PCI 0001:02 Cannot reserve Legacy IO [io 0x20000-0x20fff] pci 0000:00:00.0: BAR 9: can't assign mem pref (size 0x100000) pci 0000:01:00.0: BAR 6: assigned [mem 0xa0000000-0xa007ffff pref] pci 0000:01:00.0: BAR 2: assigned [mem 0xa0080000-0xa0083fff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0xa0084000-0xa008407f 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [io 0x0000-0xffff] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff] pci 0001:02:00.0: PCI bridge to [bus 03] pci 0001:02:00.0: bridge window [io 0x20000-0x2ffff] pci 0001:02:00.0: bridge window [mem 0x80000000-0x9fffffff] Some PCI device resources are unassigned, try booting with pci=realloc pci 0000:00:00.0: enabling device (0106 -> 0107) pci 0001:02:00.0: enabling device (0106 -> 0107) pci_bus 0000:00: resource 4 [io 0x0000-0xffff] pci_bus 0000:00: resource 5 [mem 0xa0000000-0xbfffffff] pci_bus 0000:01: resource 0 [io 0x0000-0xffff] pci_bus 0000:01: resource 1 [mem 0xa0000000-0xbfffffff] pci_bus 0001:02: resource 4 [io 0x20000-0x2ffff] pci_bus 0001:02: resource 5 [mem 0x80000000-0x9fffffff] pci_bus 0001:03: resource 0 [io 0x20000-0x2ffff] pci_bus 0001:03: resource 1 [mem 0x80000000-0x9fffffff] Setting up Freescale MSI support Registering qe_ic with sysfs... bio: create slab <bio-0> at 0 Freescale Elo / Elo Plus DMA driver fsl-elo-dma ffe0c300.dma: #0 (fsl,eloplus-dma-channel), irq 76 fsl-elo-dma ffe0c300.dma: #1 (fsl,eloplus-dma-channel), irq 77 fsl-elo-dma ffe0c300.dma: #2 (fsl,eloplus-dma-channel), irq 78 fsl-elo-dma ffe0c300.dma: #3 (fsl,eloplus-dma-channel), irq 79 fsl-elo-dma ffe21300.dma: #0 (fsl,eloplus-dma-channel), irq 20 fsl-elo-dma ffe21300.dma: #1 (fsl,eloplus-dma-channel), irq 21 fsl-elo-dma ffe21300.dma: #2 (fsl,eloplus-dma-channel), irq 22 fsl-elo-dma ffe21300.dma: #3 (fsl,eloplus-dma-channel), irq 23 vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx> PTP clock support registered EDAC MC: Ver: 3.0.0 Advanced Linux Sound Architecture Driver Initialized. Switching to clocksource timebase NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP: reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PCI: CLS 32 bytes, default 32 audit: initializing netlink socket (disabled) type=2000 audit(0.312:1): initialized bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages HugeTLB registered 16 MB page size, pre-allocated 0 pages HugeTLB registered 64 MB page size, pre-allocated 0 pages HugeTLB registered 256 MB page size, pre-allocated 0 pages HugeTLB registered 1 GB page size, pre-allocated 0 pages NFS: Registering the id_resolver key type Key type id_resolver registered Key type id_legacy registered Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). NTFS driver 2.1.30 [Flags: R/O]. jffs2: version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc. msgmni has been set to 1501 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Freescale Display Interface Unit (DIU) framebuffer driver Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A console [ttyS0] enabled, bootconsole disabled serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A Generic non-volatile memory driver v1.1 brd: module loaded loop: module loaded nbd: registered device at major 43 st: Version 20101219, fixed bufsize 32768, s/g segs 256 sata_sil24 0000:01:00.0: version 1.1 scsi0 : sata_sil24 scsi1 : sata_sil24 ata1: SATA max UDMA/100 host m128@0xa0084000 port 0xa0080000 irq 24 ata2: SATA max UDMA/100 host m128@0xa0084000 port 0xa0082000 irq 24 ef000000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101 Amd/Fujitsu Extended Query Table at 0x0040 Amd/Fujitsu Extended Query version 1.3. number of CFI chips: 1 5 ofpart partitions found on MTD device ef000000.nor Creating 5 MTD partitions on "ef000000.nor": 0x000000000000-0x000000040000 : "NOR Vitesse-7385 Firmware" ftl_cs: FTL header not found. 0x000000040000-0x000000080000 : "NOR DTB Image" ftl_cs: FTL header not found. 0x000000080000-0x000000400000 : "NOR Linux Kernel Image" ftl_cs: FTL header not found. 0x000000400000-0x000000f00000 : "NOR JFFS2 Root File System" ftl_cs: FTL header not found. 0x000000f00000-0x000001000000 : "NOR U-Boot Image" ftl_cs: FTL header not found. NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit), 32MiB, page size: 512, OOB size: 16 Bad block table found at page 65504, version 0x01 Bad block table found at page 65472, version 0x01 6 ofpart partitions found on MTD device ff800000.flash Creating 6 MTD partitions on "ff800000.flash": 0x000000000000-0x000000100000 : "NAND U-Boot Image" ftl_cs: FTL header not found. 0x000000100000-0x000000200000 : "NAND DTB Image" ftl_cs: FTL header not found. 0x000000200000-0x000000600000 : "NAND Linux Kernel Image" ftl_cs: FTL header not found. 0x000000600000-0x000000a00000 : "NAND Compressed RFS Image" ftl_cs: FTL header not found. 0x000000a00000-0x000001100000 : "NAND JFFS2 Root File System" ftl_cs: FTL header not found. 0x000001100000-0x000002000000 : "NAND Writable User area" ftl_cs: FTL header not found. eLBC NAND device at 0xff800000, bank 1 fsl_espi ffe07000.spi: master is unqueued, this is deprecated m25p80 spi32766.0: found s25fl129p1, expected m25p80 m25p80 spi32766.0: s25fl129p1 (16384 Kbytes) 5 ofpart partitions found on MTD device spi32766.0 Creating 5 MTD partitions on "spi32766.0": 0x000000000000-0x000000080000 : "SPI U-Boot Image" ftl_cs: FTL header not found. 0x000000080000-0x000000100000 : "SPI DTB Image" ftl_cs: FTL header not found. 0x000000100000-0x000000500000 : "SPI Linux Kernel Image" ftl_cs: FTL header not found. 0x000000500000-0x000000900000 : "SPI Compressed RFS Image" ftl_cs: FTL header not found. 0x000000900000-0x000001000000 : "SPI JFFS2 RFS" ftl_cs: FTL header not found. fsl_espi ffe07000.spi: at 0xf10bc000 (irq = 59) libphy: Fixed MDIO Bus: probed libphy: Freescale PowerQUICC MII Bus: probed libphy: Freescale PowerQUICC MII Bus: probed fsl-gianfar ffe24000.ethernet eth0: mac: 00:04:9f:02:7f:3c fsl-gianfar ffe24000.ethernet eth0: Running with NAPI enabled fsl-gianfar ffe24000.ethernet eth0: RX BD ring size for Q[0]: 256 fsl-gianfar ffe24000.ethernet eth0: TX BD ring size for Q[0]: 256 fsl-gianfar ffe25000.ethernet eth1: mac: 00:04:9f:02:7f:3b fsl-gianfar ffe25000.ethernet eth1: Running with NAPI enabled fsl-gianfar ffe25000.ethernet eth1: RX BD ring size for Q[0]: 256 fsl-gianfar ffe25000.ethernet eth1: TX BD ring size for Q[0]: 256 fsl-gianfar ffe26000.ethernet eth2: mac: 00:04:9f:02:7f:3a fsl-gianfar ffe26000.ethernet eth2: Running with NAPI enabled fsl-gianfar ffe26000.ethernet eth2: RX BD ring size for Q[0]: 256 fsl-gianfar ffe26000.ethernet eth2: TX BD ring size for Q[0]: 256 pps pps0: new PPS source ptp0 ucc_geth_driver: QE UCC Gigabit Ethernet Controller ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage i2c /dev entries driver mpc-i2c ffe03000.i2c: timeout 1000000 us mpc-i2c ffe03100.i2c: timeout 1000000 us sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: SDHCI controller on ffe2e000.sdhc [ffe2e000.sdhc] using DMA talitos ffe30000.crypto: hwrng talitos ffe30000.crypto: fsl,sec3.1 algorithms registered in /proc/crypto usbcore: registered new interface driver usbhid usbhid: USB HID core driver snd-soc-p1022ds: missing/invalid global utils node ipip: IPv4 over IPv4 tunneling driver TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Key type dns_resolver registered /home/kevin/git/linux/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) snd-soc-p1022rdk: missing/invalid global utils node mmc0: new high speed SDHC card at address e624 mmcblk0: mmc0:e624 SU04G 3.69 GiB mmcblk0: p1 IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready usb 1-1: new high-speed USB device number 2 using fsl-ehci hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usb 1-1.3: new high-speed USB device number 3 using fsl-ehci usb-storage 1-1.3:1.0: USB Mass Storage device detected scsi2 : usb-storage 1-1.3:1.0 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 0) ata1.00: ATA-8: ST500DM002-1BC142, JC4B, max UDMA/133 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/100 scsi 0:0:0:0: Direct-Access ATA ST500DM002-1BC14 JC4B PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA scsi 2:0:0:0: Direct-Access freescale PMAP PQ: 0 ANSI: 0 CCS sd 2:0:0:0: Attached scsi generic sg1 type 0 sd 2:0:0:0: [sdb] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB) sda: sda1 sda2 sd 2:0:0:0: [sdb] Write Protect is off sd 0:0:0:0: [sda] Attached SCSI disk sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00 sd 2:0:0:0: [sdb] No Caching mode page present sd 2:0:0:0: [sdb] Assuming drive cache: write through sd 2:0:0:0: [sdb] No Caching mode page present sd 2:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb4 sd 2:0:0:0: [sdb] No Caching mode page present sd 2:0:0:0: [sdb] Assuming drive cache: write through sd 2:0:0:0: [sdb] Attached SCSI removable disk ata2: SATA link down (SStatus 0 SControl 0) libphy: mdio@ffe24520:01 - Link is Up - 1000/Full IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready IP-Config: Complete: device=eth2, hwaddr=00:04:9f:02:7f:3a, ipaddr=128.224.178.28, mask=255.255.254.0, gw=128.224.178.1 host=unknown, domain=, nis-domain=(none) bootserver=128.224.178.20, rootserver=128.224.178.20, rootpath= ALSA device list: No soundcards found. VFS: Mounted root (nfs filesystem) on device 0:17. Freeing unused kernel memory: 264K (c071d000 - c075f000) block nbd15: Attempted send on closed socket end_request: I/O error, dev nbd15, sector 2 EXT3-fs (nbd15): error: unable to read superblock block nbd14: Attempted send on closed socket end_request: I/O error, dev nbd14, sector 2 EXT3-fs (nbd14): error: unable to read superblock block nbd12: Attempted send on closed socket end_request: I/O error, dev nbd12, sector 2 EXT3-fs (nbd12): error: unable to read superblock block nbd14: Attempted send on closed socket block nbd3: Attempted send on closed socket end_request: I/O error, dev nbd3, sector 2 EXT3-fs (nbd3): error: unable to read superblock end_request: I/O error, dev nbd14, sector 2 EXT2-fs (nbd14): error: unable to read superblock block nbd12: Attempted send on closed socket end_request: I/O error, dev nbd12, sector 2 EXT2-fs (nbd12): error: unable to read superblock block nbd14: Attempted send on closed socket block nbd3: Attempted send on closed socket end_request: I/O error, dev nbd3, sector 2 EXT2-fs (nbd3): error: unable to read superblock end_request: I/O error, dev nbd14, sector 0 FAT-fs (nbd14): unable to read boot sector block nbd3: Attempted send on closed socket end_request: I/O error, dev nbd3, sector 0 FAT-fs (nbd3): unable to read boot sector block nbd0: Attempted send on closed socket end_request: I/O error, dev nbd0, sector 2 EXT3-fs (nbd0): error: unable to read superblock block nbd12: Attempted send on closed socket block nbd1: Attempted send on closed socket EXT3-fs (nbd1): error: unable to read superblock FAT-fs (nbd12): unable to read boot sector block nbd15: Attempted send on closed socket EXT2-fs (nbd15): error: unable to read superblock block nbd4: Attempted send on closed socket EXT3-fs (nbd4): error: unable to read superblock block nbd1: Attempted send on closed socket EXT2-fs (nbd1): error: unable to read superblock block nbd4: Attempted send on closed socket EXT2-fs (nbd4): error: unable to read superblock block nbd0: Attempted send on closed socket EXT2-fs (nbd0): error: unable to read superblock block nbd13: Attempted send on closed socket EXT3-fs (nbd13): error: unable to read superblock block nbd15: Attempted send on closed socket FAT-fs (nbd15): unable to read boot sector block nbd2: Attempted send on closed socket EXT3-fs (nbd2): error: unable to read superblock block nbd1: Attempted send on closed socket FAT-fs (nbd1): unable to read boot sector block nbd4: Attempted send on closed socket block nbd2: Attempted send on closed socket EXT2-fs (nbd2): error: unable to read superblock FAT-fs (nbd4): unable to read boot sector block nbd0: Attempted send on closed socket FAT-fs (nbd0): unable to read boot sector block nbd6: Attempted send on closed socket EXT3-fs (nbd6): error: unable to read superblock block nbd2: Attempted send on closed socket block nbd6: Attempted send on closed socket EXT2-fs (nbd6): error: unable to read superblock FAT-fs (nbd2): unable to read boot sector block nbd11: Attempted send on closed socket EXT3-fs (nbd11): error: unable to read superblock block nbd11: Attempted send on closed socket EXT2-fs (nbd11): error: unable to read superblock block nbd8: Attempted send on closed socket EXT3-fs (nbd8): error: unable to read superblock block nbd8: Attempted send on closed socket block nbd10: Attempted send on closed socket EXT3-fs (nbd10): error: unable to read superblock EXT2-fs (nbd8): error: unable to read superblock block nbd9: Attempted send on closed socket EXT3-fs (nbd9): error: unable to read superblock block nbd9: Attempted send on closed socket EXT2-fs (nbd9): error: unable to read superblock block nbd9: Attempted send on closed socket FAT-fs (nbd9): unable to read boot sector block nbd7: Attempted send on closed socket EXT3-fs (nbd7): error: unable to read superblock block nbd11: Attempted send on closed socket FAT-fs (nbd11): unable to read boot sector block nbd7: Attempted send on closed socket EXT2-fs (nbd7): error: unable to read superblock block nbd13: Attempted send on closed socket EXT2-fs (nbd13): error: unable to read superblock block nbd8: Attempted send on closed socket FAT-fs (nbd8): unable to read boot sector block nbd6: Attempted send on closed socket FAT-fs (nbd6): unable to read boot sector block nbd10: Attempted send on closed socket EXT2-fs (nbd10): error: unable to read superblock block nbd5: Attempted send on closed socket EXT3-fs (nbd5): error: unable to read superblock block nbd10: Attempted send on closed socket FAT-fs (nbd10): unable to read boot sector block nbd13: Attempted send on closed socket block nbd5: Attempted send on closed socket EXT2-fs (nbd5): error: unable to read superblock FAT-fs (nbd13): unable to read boot sector block nbd5: Attempted send on closed socket FAT-fs (nbd5): unable to read boot sector block nbd7: Attempted send on closed socket FAT-fs (nbd7): unable to read boot sector EXT3-fs (mmcblk0): error: can't find ext3 filesystem on dev mmcblk0. EXT2-fs (mmcblk0): error: can't find an ext2 filesystem on dev mmcblk0. FAT-fs (mmcblk0): bogus number of reserved sectors FAT-fs (mmcblk0): Can't find a valid FAT filesystem EXT3-fs (sda): error: can't find ext3 filesystem on dev sda. EXT2-fs (sda): error: can't find an ext2 filesystem on dev sda. FAT-fs (sda): bogus number of reserved sectors FAT-fs (sda): Can't find a valid FAT filesystem cramfs: wrong magic cramfs: wrong magic NTFS-fs error (device mmcblk0): read_ntfs_boot_sector(): Primary boot sector is invalid. NTFS-fs error (device mmcblk0): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover. NTFS-fs error (device mmcblk0): ntfs_fill_super(): Not an NTFS volume. NTFS-fs error (device sda): read_ntfs_boot_sector(): Primary boot sector is invalid. NTFS-fs error (device sda): read_ntfs_boot_sector(): Mount option errors=recover not used. Aborting without trying to recover. NTFS-fs error (device sda): ntfs_fill_super(): Not an NTFS volume. FAT-fs (sdb): Invalid FSINFO signature: 0x00000000, 0x00000000 (sector = 1) FAT-fs (sdb): codepage cp437 not found EXT2-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended kjournald starting. Commit interval 5 seconds EXT3-fs (sda1): using internal journal EXT3-fs (sda1): recovery complete EXT3-fs (sda1): mounted filesystem with writeback data mode EXT2-fs (sdb4): warning: mounting unchecked fs, running e2fsck is recommended root@unknown:~# lspci -vvv 0000:00:00.0 PCI bridge: Freescale Semiconductor Inc P2020E (rev 21) (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Region 0: Memory at <ignored> (32-bit, non-prefetchable) Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: e0000000-ffffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [4c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <2us, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- 0000:01:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01) Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 24 Region 0: Memory at a0084000 (64-bit, non-prefetchable) [size=128] Region 2: Memory at a0080000 (64-bit, non-prefetchable) [size=16K] Region 4: I/O ports at 1000 [size=128] [virtual] Expansion ROM at a0000000 [disabled] [size=512K] Capabilities: [54] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00 DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Kernel driver in use: sata_sil24 0001:02:00.0 PCI bridge: Freescale Semiconductor Inc P2020E (rev 21) (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at <ignored> (32-bit, non-prefetchable) Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: e0000000-ffffffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [4c] Express (v1) Root Port (Slot-), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <2us, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Attachment:
pgpq2p_ajRs__.pgp
Description: PGP signature