Thanks again, Martin.
Firstly, maybe we should remove the linux-media list from the copy list.
I imagine this hotplug stuff is just noise to them.
[snip]
Do you have any other express card around to try if it works at all? Try that always after a cold boot.
Not at the moment, but I ordered at USB3 expresscard yesterday, so I
will have one soon.
Posting a diff result of the below procedure might help:
# lspci -vvvxxx > lspci.before_insertion.txt
[plug your card into the slot]
# lspci -vvvxxx > lspci.after_insertion.txt
[ unplug your card]
# lspci -vvvxxx > lspci.after_1st_removal.txt
[re-plug your card into the slot]
# lspci -vvvxxx > lspci.after_1st_re-insertion.txt
[ unplug your card]
# lspci -vvvxxx > lspci.after_2nd_removal.txt
OK, I've been using kernel 3.8.0-rc kernels so far, but given that is
still under development, I've switched to 3.7.4, mainly because you are
having success with 3.7.x, acpiphp and pcie_aspm=off. I verified the
environment as follows:
[chris:~]$ cat /proc/cmdline
root=/dev/sda5 pcie_aspm=off ro resume=/dev/sda6
[chris:~]$ dmesg | grep ASPM
[ 0.000000] PCIe ASPM is disabled
[ 0.348959] pci0000:00: ACPI _OSC support notification failed,
disabling PCIe ASPM
[chris:~]$ dmesg | grep acpiphp
[ 0.400846] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[chris:~]$ dmesg | grep pciehp
[chris:~]$ uname -a
Linux laptop 3.7.4 #13 SMP PREEMPT Sun Jan 27 18:39:39 GMT 2013 i686
GNU/Linux
Then compare them using diff. These should have no difference:
diff lspci.after_insertion.txt lspci.after_1st_re-insertion.txt
diff lspci.after_1st_removal.txt lspci.after_2nd_removal.txt
Correct, there were no differences.
These may have only little difference, or none:
diff lspci.before_insertion.txt lspci.after_1st_removal.txt
263c263
< LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <16us
---
> LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <512ns, L1 <16us
265c265
< LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk-
---
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
267c267
< LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
---
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt+ ABWMgmt-
273c273
< Changed: MRL- PresDet- LinkState-
---
> Changed: MRL- PresDet- LinkState+
295,296c295,296
< 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 4c 12 04
< 50: 03 00 01 10 60 b2 1c 00 08 00 00 00 00 00 00 00
---
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 04
> 50: 40 00 11 50 60 b2 1c 00 08 00 00 01 00 00 00 00
diff lspci.after_1st_removal.txt lspci.after_2nd_removal.txt
No difference.
Finally, these should confirm whether the PresDet works for you (for me NOT with pciehp but does work with acpiphp).
You should see PresDet- to PresDet+ changes in:
Yes, I do see the PresDet- to PresDet+ changes
diff lspci.before_insertion.txt lspci.after_insertion.txt
263c263
< LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <1us, L1 <16us
---
> LnkCap: Port #4, Speed 5GT/s, Width x1, ASPM L0s L1,
Latency L0 <512ns, L1 <16us
265c265
< LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled-
Retrain- CommClk-
---
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
267c267
< LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
---
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
272,273c272,273
< SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
< Changed: MRL- PresDet- LinkState-
---
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState+
295,296c295,296
< 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 4c 12 04
< 50: 03 00 01 10 60 b2 1c 00 08 00 00 00 00 00 00 00
---
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 04
> 50: 40 00 11 70 60 b2 1c 00 08 00 40 01 00 00 00 00
diff lspci.after_1st_removal.txt lspci.after_1st_re-insertion.txt
267c267
< LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt+ ABWMgmt-
---
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
272c272
< SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
---
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
296c296
< 50: 40 00 11 50 60 b2 1c 00 08 00 00 01 00 00 00 00
---
> 50: 40 00 11 70 60 b2 1c 00 08 00 40 01 00 00 00 00
You should see PresDet+ to PresDet- changes in:
Yes, I see those changes too.
diff lspci.after_insertion.txt lspci.after_1st_removal.txt
267c267
< LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
---
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt+ ABWMgmt-
272c272
< SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
---
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
296c296
< 50: 40 00 11 70 60 b2 1c 00 08 00 40 01 00 00 00 00
---
> 50: 40 00 11 50 60 b2 1c 00 08 00 00 01 00 00 00 00
diff lspci.after_1st_re-insertion.txt lspci.after_2nd_removal.txt
267c267
< LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
---
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train-
SlotClk+ DLActive- BWMgmt+ ABWMgmt-
272c272
< SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet+ Interlock-
---
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt-
PresDet- Interlock-
296c296
< 50: 40 00 11 70 60 b2 1c 00 08 00 40 01 00 00 00 00
---
> 50: 40 00 11 50 60 b2 1c 00 08 00 00 01 00 00 00 00
I did plenty of these with my laptop using 3.3.x and 3.7.1 and the conclusion was
that pciehp got broken since some 3.6? (commit 0d52f54e2ef64c189dedc332e680b2eb4a34590a)
but I can live on 3.7.x with acpiphp and pcie_aspm=off.
I could live with that too, but despite my findings being in line with
your predictions, hotplug does not work for me.
The above test could tell you what
works in your case. Of course, you can try separately pciehp and acpiphp. With 3.4
series I lived with pciehp and pcie_aspm=force.
Need sleep now, but tomorrow, I'll build a 3.4 kernel and try pciehp and
pcie_aspm=force.
Martin
BTW: Re-post your dmesg output so that we can see if you those OSC errors
(for details see "Re: Dell Vostro 3550: pci_hotplug+acpiphp require 'pcie_aspm=force' on kernel command-line for hotplug to work" thread).
I've attached a file containing the output from dmesg. I does contain
errors related to OSC.
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.7.4 (chris@laptop) (gcc version 4.7.3 20130126 (prerelease) (GCC) ) #13 SMP PREEMPT Sun Jan 27 18:39:39 GMT 2013
[ 0.000000] Disabled fast string operations
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008ffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dab0efff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dab0f000-0x00000000dad4efff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dad4f000-0x00000000dad6efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dad6f000-0x00000000daf1efff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000daf1f000-0x00000000daf9efff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000daf9f000-0x00000000daffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000dafff000-0x00000000daffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db000000-0x00000000df9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffd80000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000021fdfffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.6 present.
[ 0.000000] DMI: FUJITSU LIFEBOOK AH531/FJNBB0F, BIOS 1.27 12/08/2011
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x21fe00 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 080000000 mask FC0000000 write-back
[ 0.000000] 3 base 0C0000000 mask FE0000000 write-back
[ 0.000000] 4 base 0DC000000 mask FFC000000 uncachable
[ 0.000000] 5 base 0DB000000 mask FFF000000 uncachable
[ 0.000000] 6 base 100000000 mask F00000000 write-back
[ 0.000000] 7 base 200000000 mask FE0000000 write-back
[ 0.000000] 8 base 21FE00000 mask FFFE00000 uncachable
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
[ 0.000000] Base memory trampoline at [c008c000] 8c000 size 16384
[ 0.000000] reserving inaccessible SNB gfx pages
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x37bfdfff]
[ 0.000000] [mem 0x00000000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x379fffff] page 2M
[ 0.000000] [mem 0x37a00000-0x37bfdfff] page 4k
[ 0.000000] kernel direct mapping tables up to 0x37bfdfff @ [mem 0x01bfa000-0x01bfffff]
[ 0.000000] ACPI: RSDP 000f00e0 00024 (v02 FUJ )
[ 0.000000] ACPI: XSDT daffe120 00084 (v01 FUJ PC 00000001 FUJ 00000001)
[ 0.000000] ACPI: FACP daff0000 000F4 (v03 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: DSDT daff3000 0794A (v02 FUJ FJNBB0F 00000000 INTL 20061109)
[ 0.000000] ACPI: FACS daf3d000 00040
[ 0.000000] ACPI: SLIC daffd000 00176 (v01 FUJ PC 00000001 FUJ 00000001)
[ 0.000000] ACPI: SSDT daffb000 01068 (v01 FUJ PtidDevc 00001000 INTL 20061109)
[ 0.000000] ACPI: ASF! daff2000 000A5 (v32 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: HPET dafef000 00038 (v01 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: APIC dafee000 00098 (v01 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: MCFG dafed000 0003C (v01 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: SSDT dafec000 007C2 (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT dafeb000 00996 (v01 PmRef CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: UEFI dafea000 0003E (v01 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: UEFI dafe9000 00042 (v01 PTL COMBUF 00000001 PTL 00000001)
[ 0.000000] ACPI: UEFI dafe8000 00242 (v01 FUJ PC 00000001 PTL 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 7810MB HIGHMEM available.
[ 0.000000] 891MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 37bfe000
[ 0.000000] low ram: 0 - 37bfe000
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x37bfdfff]
[ 0.000000] HighMem [mem 0x37bfe000-0x1fdfffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0008ffff]
[ 0.000000] node 0: [mem 0x00100000-0xdab0efff]
[ 0.000000] node 0: [mem 0xdafff000-0xdaffffff]
[ 0.000000] node 0: [mem 0x00000000-0x1fdfffff]
[ 0.000000] On node 0 totalpages: 2074768
[ 0.000000] free_area_init_node: node 0, pgdat c156a780, node_mem_map f37fd200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3936 pages, LIFO batch:0
[ 0.000000] Normal zone: 1752 pages used for memmap
[ 0.000000] Normal zone: 222502 pages, LIFO batch:31
[ 0.000000] HighMem zone: 15621 pages used for memmap
[ 0.000000] HighMem zone: 1830925 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x0e] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 14, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a301 base: 0xfed00000
[ 0.000000] smpboot: 8 Processors exceeds NR_CPUS limit of 4
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 0000000000090000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
[ 0.000000] setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 12 pages/cpu @f37bb000 s25792 r0 d23360 u49152
[ 0.000000] pcpu-alloc: s25792 r0 d23360 u49152 alloc=12*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2057363
[ 0.000000] Kernel command line: root=/dev/sda5 pcie_aspm=off ro resume=/dev/sda6
[ 0.000000] PCIe ASPM is disabled
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Initializing HighMem for node 0 (00037bfe:0021fe00)
[ 0.000000] Memory: 8221556k/8910848k available (4093k kernel code, 77512k reserved, 1474k data, 372k init, 7386180k highmem)
[ 0.000000] virtual kernel memory layout:
fixmap : 0xfff67000 - 0xfffff000 ( 608 kB)
pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
vmalloc : 0xf83fe000 - 0xffbfe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf7bfe000 ( 891 MB)
.init : 0xc1570000 - 0xc15cd000 ( 372 kB)
.data : 0xc13ff690 - 0xc156fec0 (1474 kB)
.text : 0xc1000000 - 0xc13ff690 (4093 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] NR_IRQS:2304 nr_irqs:712 16
[ 0.000000] CPU 0 irqstacks, hard=f3008000 soft=f300a000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 2494.153 MHz processor
[ 0.000001] Calibrating delay loop (skipped), value calculated using timer frequency.. 4988.30 BogoMIPS (lpj=9976612)
[ 0.000115] pid_max: default: 32768 minimum: 301
[ 0.000197] Mount-cache hash table entries: 512
[ 0.000404] Disabled fast string operations
[ 0.000459] CPU: Physical Processor ID: 0
[ 0.000521] CPU: Processor Core ID: 0
[ 0.000579] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.000658] mce: CPU supports 7 MCE banks
[ 0.000720] CPU0: Thermal monitoring enabled (TM1)
[ 0.000780] process: using mwait in idle threads
[ 0.000841] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
tlb_flushall_shift: 5
[ 0.001040] Freeing SMP alternatives: 16k freed
[ 0.001098] ACPI: Core revision 20120913
[ 0.005809] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.006284] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.045971] smpboot: CPU0: Intel(R) Core(TM) i5-2450M CPU @ 2.50GHz (fam: 06, model: 2a, stepping: 07)
[ 0.152281] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
[ 0.152513] perf_event_intel: PEBS disabled due to CPU errata, please upgrade microcode
[ 0.152574] ... version: 3
[ 0.152629] ... bit width: 48
[ 0.152683] ... generic registers: 4
[ 0.152738] ... value mask: 0000ffffffffffff
[ 0.152794] ... max period: 000000007fffffff
[ 0.152851] ... fixed-purpose events: 3
[ 0.152906] ... event mask: 000000070000000f
[ 0.184322] CPU 1 irqstacks, hard=f309a000 soft=f309c000
[ 0.194584] Initializing CPU#1
[ 0.195337] Disabled fast string operations
[ 0.184325] smpboot: Booting Node 0, Processors #1
[ 0.204295] CPU 2 irqstacks, hard=f30b2000 soft=f30b4000
[ 0.214730] Initializing CPU#2
[ 0.215518] Disabled fast string operations
[ 0.204464] #2
[ 0.224271] CPU 3 irqstacks, hard=f30be000 soft=f30c8000
[ 0.224441] #3 OK
[ 0.234718] Initializing CPU#3
[ 0.235505] Disabled fast string operations
[ 0.237613] Brought up 4 CPUs
[ 0.237775] smpboot: Total of 4 processors activated (19953.22 BogoMIPS)
[ 0.240453] devtmpfs: initialized
[ 0.240677] PM: Registering ACPI NVS region [mem 0xdad4f000-0xdad6efff] (131072 bytes)
[ 0.240740] PM: Registering ACPI NVS region [mem 0xdaf1f000-0xdaf9efff] (524288 bytes)
[ 0.240865] NET: Registered protocol family 16
[ 0.241064] ACPI: bus type pci registered
[ 0.241159] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.241234] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.241293] PCI: Using MMCONFIG for extended config space
[ 0.241350] PCI: Using configuration type 1 for base access
[ 0.242532] bio: create slab <bio-0> at 0
[ 0.242626] ACPI: Added _OSI(Module Device)
[ 0.242681] ACPI: Added _OSI(Processor Device)
[ 0.242737] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.242793] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.244072] ACPI: EC: Look up EC in DSDT
[ 0.245320] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.264186] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.264622] ACPI: SSDT dad4d718 0067C (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.265074] ACPI: Dynamic OEM Table Load:
[ 0.265206] ACPI: SSDT (null) 0067C (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
[ 0.284370] ACPI: SSDT daf0fa98 00303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.284847] ACPI: Dynamic OEM Table Load:
[ 0.284980] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20061109)
[ 0.304224] ACPI: SSDT dad4cd98 00119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.304667] ACPI: Dynamic OEM Table Load:
[ 0.304800] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20061109)
[ 0.324680] ACPI: Interpreter enabled
[ 0.324738] ACPI: (supports S0 S3 S4 S5)
[ 0.324962] ACPI: Using IOAPIC for interrupt routing
[ 0.328321] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.328514] ACPI: No dock devices found.
[ 0.328572] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.328920] \_SB_.PCI0:_OSC invalid UUID
[ 0.328921] _OSC request data:1 8 1f
[ 0.328924] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.329438] PCI host bridge to bus 0000:00
[ 0.329495] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.329553] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.329611] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.329670] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.329730] pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfeafffff]
[ 0.329789] pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed44fff]
[ 0.329855] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[ 0.329887] pci 0000:00:02.0: [8086:0126] type 00 class 0x030000
[ 0.329896] pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf03fffff 64bit]
[ 0.329902] pci 0000:00:02.0: reg 18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.329906] pci 0000:00:02.0: reg 20: [io 0x4000-0x403f]
[ 0.329953] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.329976] pci 0000:00:16.0: reg 10: [mem 0xf1605000-0xf160500f 64bit]
[ 0.330038] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.330071] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.330092] pci 0000:00:1a.0: reg 10: [mem 0xf160a000-0xf160a3ff]
[ 0.330165] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.330190] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.330205] pci 0000:00:1b.0: reg 10: [mem 0xf1600000-0xf1603fff 64bit]
[ 0.330259] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.330285] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.330385] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.330422] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[ 0.330523] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.330556] pci 0000:00:1c.5: [8086:1c1a] type 01 class 0x060400
[ 0.330616] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.330647] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.330667] pci 0000:00:1d.0: reg 10: [mem 0xf1609000-0xf16093ff]
[ 0.330739] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.330766] pci 0000:00:1f.0: [8086:1c49] type 00 class 0x060100
[ 0.330878] pci 0000:00:1f.2: [8086:1c03] type 00 class 0x010601
[ 0.330896] pci 0000:00:1f.2: reg 10: [io 0x4088-0x408f]
[ 0.330904] pci 0000:00:1f.2: reg 14: [io 0x4094-0x4097]
[ 0.330912] pci 0000:00:1f.2: reg 18: [io 0x4080-0x4087]
[ 0.330920] pci 0000:00:1f.2: reg 1c: [io 0x4090-0x4093]
[ 0.330927] pci 0000:00:1f.2: reg 20: [io 0x4060-0x407f]
[ 0.330935] pci 0000:00:1f.2: reg 24: [mem 0xf1608000-0xf16087ff]
[ 0.330967] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.330986] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500
[ 0.331001] pci 0000:00:1f.3: reg 10: [mem 0xf1604000-0xf16040ff 64bit]
[ 0.331022] pci 0000:00:1f.3: reg 20: [io 0xefa0-0xefbf]
[ 0.331276] pci 0000:01:00.0: [8086:008a] type 00 class 0x028000
[ 0.331424] pci 0000:01:00.0: reg 10: [mem 0xf1500000-0xf1501fff 64bit]
[ 0.331976] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[ 0.340174] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.340238] pci 0000:00:1c.0: bridge window [mem 0xf1500000-0xf15fffff]
[ 0.340316] pci 0000:00:1c.3: PCI bridge to [bus 02-06]
[ 0.340376] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
[ 0.340381] pci 0000:00:1c.3: bridge window [mem 0xf0d00000-0xf14fffff]
[ 0.340389] pci 0000:00:1c.3: bridge window [mem 0xf0400000-0xf0bfffff 64bit pref]
[ 0.340456] pci 0000:07:00.0: [10ec:8168] type 00 class 0x020000
[ 0.340476] pci 0000:07:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.340510] pci 0000:07:00.0: reg 18: [mem 0xf0c04000-0xf0c04fff 64bit pref]
[ 0.340531] pci 0000:07:00.0: reg 20: [mem 0xf0c00000-0xf0c03fff 64bit pref]
[ 0.340591] pci 0000:07:00.0: supports D1 D2
[ 0.340592] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.348055] pci 0000:00:1c.5: PCI bridge to [bus 07]
[ 0.348681] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
[ 0.348689] pci 0000:00:1c.5: bridge window [mem 0xf0c00000-0xf0cfffff 64bit pref]
[ 0.348710] pci_bus 0000:00: on NUMA node 0
[ 0.348712] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.348826] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.348857] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.348885] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.348956] \_SB_.PCI0:_OSC invalid UUID
[ 0.348957] _OSC request data:1 9 1f
[ 0.348959] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.349021] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.351134] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.351698] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.352262] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.352822] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 10 *11 12 14 15)
[ 0.353384] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.354024] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.354664] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.355226] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 *10 11 12 14 15)
[ 0.355802] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.355865] vgaarb: loaded
[ 0.355917] vgaarb: bridge control possible 0000:00:02.0
[ 0.356025] SCSI subsystem initialized
[ 0.356079] ACPI: bus type scsi registered
[ 0.356146] libata version 3.00 loaded.
[ 0.356149] ACPI: bus type usb registered
[ 0.356220] usbcore: registered new interface driver usbfs
[ 0.356285] usbcore: registered new interface driver hub
[ 0.356359] usbcore: registered new device driver usb
[ 0.356430] Linux video capture interface: v2.00
[ 0.356511] Advanced Linux Sound Architecture Driver Initialized.
[ 0.356569] PCI: Using ACPI for IRQ routing
[ 0.358248] PCI: pci_cache_line_size set to 64 bytes
[ 0.358345] e820: reserve RAM buffer [mem 0xdab0f000-0xdbffffff]
[ 0.358347] e820: reserve RAM buffer [mem 0xdb000000-0xdbffffff]
[ 0.358348] e820: reserve RAM buffer [mem 0x21fe00000-0x21fffffff]
[ 0.358468] Switching to clocksource hpet
[ 0.358566] pnp: PnP ACPI init
[ 0.358622] ACPI: bus type pnp registered
[ 0.358918] pnp 00:00: [bus 00-3e]
[ 0.358920] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.358921] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.358923] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.358924] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.358925] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.358928] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.358929] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.358930] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.358932] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.358933] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.358934] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.358935] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.358937] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.358938] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.358939] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.358940] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.358941] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.358943] pnp 00:00: [mem 0xdfa00000-0xfeafffff window]
[ 0.358944] pnp 00:00: [mem 0xfed40000-0xfed44fff window]
[ 0.358964] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.358978] pnp 00:01: [io 0x0000-0x001f]
[ 0.358979] pnp 00:01: [io 0x0081-0x0091]
[ 0.358980] pnp 00:01: [io 0x0093-0x009f]
[ 0.358981] pnp 00:01: [io 0x00c0-0x00df]
[ 0.358983] pnp 00:01: [dma 4]
[ 0.358994] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.358999] pnp 00:02: [mem 0xff000000-0xffffffff]
[ 0.359010] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.359063] pnp 00:03: [mem 0xfed00000-0xfed003ff]
[ 0.359075] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.359081] pnp 00:04: [io 0x00f0]
[ 0.359088] pnp 00:04: [irq 13]
[ 0.359099] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.359108] pnp 00:05: [io 0x002e-0x002f]
[ 0.359109] pnp 00:05: [io 0x004e-0x004f]
[ 0.359110] pnp 00:05: [io 0x0061]
[ 0.359111] pnp 00:05: [io 0x0063]
[ 0.359112] pnp 00:05: [io 0x0065]
[ 0.359113] pnp 00:05: [io 0x0067]
[ 0.359114] pnp 00:05: [io 0x0070]
[ 0.359115] pnp 00:05: [io 0x0080]
[ 0.359116] pnp 00:05: [io 0x0092]
[ 0.359117] pnp 00:05: [io 0x00b2-0x00b3]
[ 0.359118] pnp 00:05: [io 0x0680-0x069f]
[ 0.359119] pnp 00:05: [io 0x1000-0x100f]
[ 0.359120] pnp 00:05: [io 0xffff]
[ 0.359122] pnp 00:05: [io 0xffff]
[ 0.359123] pnp 00:05: [io 0x0400-0x0453]
[ 0.359124] pnp 00:05: [io 0x0458-0x047f]
[ 0.359125] pnp 00:05: [io 0x0500-0x057f]
[ 0.359126] pnp 00:05: [io 0x164e-0x164f]
[ 0.359127] pnp 00:05: [io 0x0068-0x0077]
[ 0.359148] system 00:05: [io 0x0680-0x069f] has been reserved
[ 0.359206] system 00:05: [io 0x1000-0x100f] has been reserved
[ 0.359264] system 00:05: [io 0xffff] has been reserved
[ 0.359322] system 00:05: [io 0xffff] has been reserved
[ 0.359379] system 00:05: [io 0x0400-0x0453] has been reserved
[ 0.359436] system 00:05: [io 0x0458-0x047f] has been reserved
[ 0.359494] system 00:05: [io 0x0500-0x057f] has been reserved
[ 0.359552] system 00:05: [io 0x164e-0x164f] has been reserved
[ 0.359611] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.359616] pnp 00:06: [io 0x0070-0x0077]
[ 0.359620] pnp 00:06: [irq 8]
[ 0.359631] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.359651] pnp 00:07: [io 0x0454-0x0457]
[ 0.359669] system 00:07: [io 0x0454-0x0457] has been reserved
[ 0.359727] system 00:07: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.359733] pnp 00:08: [io 0x0060]
[ 0.359734] pnp 00:08: [io 0x0064]
[ 0.359738] pnp 00:08: [irq 1]
[ 0.359749] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.359757] pnp 00:09: [irq 12]
[ 0.359768] pnp 00:09: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 0.359854] pnp 00:0a: [mem 0xfed1c000-0xfed1ffff]
[ 0.359855] pnp 00:0a: [mem 0xfed10000-0xfed17fff]
[ 0.359857] pnp 00:0a: [mem 0xfed18000-0xfed18fff]
[ 0.359858] pnp 00:0a: [mem 0xfed19000-0xfed19fff]
[ 0.359859] pnp 00:0a: [mem 0xf8000000-0xfbffffff]
[ 0.359860] pnp 00:0a: [mem 0xfed20000-0xfed3ffff]
[ 0.359861] pnp 00:0a: [mem 0xfed90000-0xfed93fff]
[ 0.359862] pnp 00:0a: [mem 0xfed45000-0xfed8ffff]
[ 0.359863] pnp 00:0a: [mem 0xff000000-0xffffffff]
[ 0.359865] pnp 00:0a: [mem 0xfee00000-0xfeefffff]
[ 0.359866] pnp 00:0a: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.359886] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.359946] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.360005] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.360074] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.360134] system 00:0a: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.360194] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.360253] system 00:0a: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.360313] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.360373] system 00:0a: [mem 0xff000000-0xffffffff] could not be reserved
[ 0.360433] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.360493] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.360642] pnp 00:0b: [mem 0x20000000-0x201fffff]
[ 0.360643] pnp 00:0b: [mem 0x40000000-0x401fffff]
[ 0.360665] system 00:0b: [mem 0x20000000-0x201fffff] could not be reserved
[ 0.360725] system 00:0b: [mem 0x40000000-0x401fffff] could not be reserved
[ 0.360785] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.360817] pnp: PnP ACPI: found 12 devices
[ 0.360872] ACPI: ACPI bus type pnp unregistered
[ 0.396678] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.396741] pci 0000:00:1c.0: bridge window [mem 0xf1500000-0xf15fffff]
[ 0.396811] pci 0000:00:1c.3: PCI bridge to [bus 02-06]
[ 0.396871] pci 0000:00:1c.3: bridge window [io 0x3000-0x3fff]
[ 0.396934] pci 0000:00:1c.3: bridge window [mem 0xf0d00000-0xf14fffff]
[ 0.396998] pci 0000:00:1c.3: bridge window [mem 0xf0400000-0xf0bfffff 64bit pref]
[ 0.397066] pci 0000:00:1c.5: PCI bridge to [bus 07]
[ 0.397123] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
[ 0.397185] pci 0000:00:1c.5: bridge window [mem 0xf0c00000-0xf0cfffff 64bit pref]
[ 0.397274] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.397276] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.397277] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.397278] pci_bus 0000:00: resource 7 [mem 0xdfa00000-0xfeafffff]
[ 0.397280] pci_bus 0000:00: resource 8 [mem 0xfed40000-0xfed44fff]
[ 0.397281] pci_bus 0000:01: resource 1 [mem 0xf1500000-0xf15fffff]
[ 0.397282] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
[ 0.397284] pci_bus 0000:02: resource 1 [mem 0xf0d00000-0xf14fffff]
[ 0.397285] pci_bus 0000:02: resource 2 [mem 0xf0400000-0xf0bfffff 64bit pref]
[ 0.397286] pci_bus 0000:07: resource 0 [io 0x2000-0x2fff]
[ 0.397288] pci_bus 0000:07: resource 2 [mem 0xf0c00000-0xf0cfffff 64bit pref]
[ 0.397310] NET: Registered protocol family 2
[ 0.397457] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.397703] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.397849] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.397922] TCP: reno registered
[ 0.397977] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.398038] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.398133] NET: Registered protocol family 1
[ 0.398196] pci 0000:00:02.0: Boot video device
[ 0.398293] PCI: CLS 64 bytes, default 64
[ 0.398912] bounce pool size: 64 pages
[ 0.400057] fuse init (API version 7.20)
[ 0.400171] msgmni has been set to 1631
[ 0.400453] io scheduler noop registered
[ 0.400528] io scheduler cfq registered (default)
[ 0.400788] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.400846] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.401204] ACPI: AC Adapter [ACAD] (on-line)
[ 0.401302] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.401366] ACPI: Power Button [PWRB]
[ 0.401445] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 0.401520] ACPI: Lid Switch [LID]
[ 0.401598] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.401659] ACPI: Power Button [PWRF]
[ 0.404598] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.404657] ACPI: Thermal Zone [THRM] (58 C)
[ 0.404724] isapnp: Scanning for PnP cards...
[ 0.405301] ACPI: Battery Slot [BAT1] (battery present)
[ 0.758276] isapnp: No Plug & Play device found
[ 0.762777] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.763137] Real Time Clock Driver v1.12b
[ 0.763192] Linux agpgart interface v0.103
[ 0.763269] [drm] Initialized drm 1.1.0 20060810
[ 0.763467] pci 0000:00:00.0: Intel Sandybridge Chipset
[ 0.763552] pci 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable
[ 0.764350] pci 0000:00:00.0: detected 65536K stolen memory
[ 0.764450] i915 0000:00:02.0: setting latency timer to 64
[ 0.764618] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 0.764677] [drm] Driver supports precise vblank timestamp query.
[ 0.764767] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 0.950840] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 1.121073] fbcon: inteldrmfb (fb0) is primary device
[ 1.393219] tsc: Refined TSC clocksource calibration: 2494.337 MHz
[ 1.393225] Switching to clocksource tsc
[ 2.301651] Console: switching to colour frame buffer device 170x48
[ 2.304426] fb0: inteldrmfb frame buffer device
[ 2.304441] drm: registered panic notifier
[ 2.336754] acpi device:31: registered as cooling_device4
[ 2.336887] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.336940] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
[ 2.336984] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 2.337077] ahci 0000:00:1f.2: version 3.0
[ 2.351993] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x9 impl SATA mode
[ 2.352066] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst
[ 2.352098] ahci 0000:00:1f.2: setting latency timer to 64
[ 2.360245] scsi0 : ahci
[ 2.360297] scsi1 : ahci
[ 2.360338] scsi2 : ahci
[ 2.360379] scsi3 : ahci
[ 2.360419] scsi4 : ahci
[ 2.360462] scsi5 : ahci
[ 2.360495] ata1: SATA max UDMA/133 abar m2048@0xf1608000 port 0xf1608100 irq 19
[ 2.360522] ata2: DUMMY
[ 2.360529] ata3: DUMMY
[ 2.360539] ata4: SATA max UDMA/133 abar m2048@0xf1608000 port 0xf1608280 irq 19
[ 2.360565] ata5: DUMMY
[ 2.360572] ata6: DUMMY
[ 2.360607] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.361483] ehci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.361485] ehci_hcd 0000:00:1a.0: EHCI Host Controller
[ 2.362308] ehci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.363138] ehci_hcd 0000:00:1a.0: debug port 2
[ 2.367834] ehci_hcd 0000:00:1a.0: cache line size of 64 is not supported
[ 2.367838] ehci_hcd 0000:00:1a.0: irq 16, io mem 0xf160a000
[ 2.379932] ehci_hcd 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 2.380791] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.381576] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.382360] usb usb1: Product: EHCI Host Controller
[ 2.383143] usb usb1: Manufacturer: Linux 3.7.4 ehci_hcd
[ 2.383927] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.384781] hub 1-0:1.0: USB hub found
[ 2.385552] hub 1-0:1.0: 2 ports detected
[ 2.386366] ehci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.386369] ehci_hcd 0000:00:1d.0: EHCI Host Controller
[ 2.387136] ehci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.387924] ehci_hcd 0000:00:1d.0: debug port 2
[ 2.392582] ehci_hcd 0000:00:1d.0: cache line size of 64 is not supported
[ 2.392594] ehci_hcd 0000:00:1d.0: irq 23, io mem 0xf1609000
[ 2.403903] ehci_hcd 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 2.404733] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.405495] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.406253] usb usb2: Product: EHCI Host Controller
[ 2.406997] usb usb2: Manufacturer: Linux 3.7.4 ehci_hcd
[ 2.407726] usb usb2: SerialNumber: 0000:00:1d.0
[ 2.408508] hub 2-0:1.0: USB hub found
[ 2.409222] hub 2-0:1.0: 2 ports detected
[ 2.409974] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.410732] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.417631] i8042: Detected active multiplexing controller, rev 1.1
[ 2.421750] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.422491] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 2.423221] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 2.423938] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 2.424625] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 2.425324] mousedev: PS/2 mouse device common for all mice
[ 2.426045] i2c /dev entries driver
[ 2.426811] ACPI Warning: 0x0000efa0-0x0000efbf SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120913/utaddress-251)
[ 2.427493] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.428222] IR NEC protocol handler initialized
[ 2.428941] IR RC5(x) protocol handler initialized
[ 2.429660] IR RC6 protocol handler initialized
[ 2.430388] IR JVC protocol handler initialized
[ 2.431116] IR Sony protocol handler initialized
[ 2.431839] IR RC5 (streamzap) protocol handler initialized
[ 2.432553] IR SANYO protocol handler initialized
[ 2.433274] IR MCE Keyboard/mouse protocol handler initialized
[ 2.434021] usbcore: registered new interface driver uvcvideo
[ 2.434740] USB Video Class driver (1.1.1)
[ 2.435465] cpuidle: using governor ladder
[ 2.436180] cpuidle: using governor menu
[ 2.437050] usbcore: registered new interface driver usbhid
[ 2.437761] usbhid: USB HID core driver
[ 2.438549] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.439262] TCP: cubic registered
[ 2.439986] NET: Registered protocol family 17
[ 2.440699] NET: Registered protocol family 15
[ 2.441512] Using IPI No-Shortcut mode
[ 2.448477] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 2.679555] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.686216] ata4.00: ATAPI: TSSTcorp CDDVDW SN-208AB, FC01, max UDMA/100
[ 2.687543] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.692366] ata4.00: configured for UDMA/100
[ 2.695530] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 2.741379] ata1.00: ATA-8: TOSHIBA MK7575GSX, GT001A, max UDMA/100
[ 2.742196] ata1.00: 1465149168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.743038] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 2.743875] ata1.00: failed to get Identify Device Data, Emask 0x1
[ 2.743881] ata1.00: configured for UDMA/100
[ 2.751592] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK7575GS GT00 PQ: 0 ANSI: 5
[ 2.752481] sd 0:0:0:0: [sda] 1465149168 512-byte logical blocks: (750 GB/698 GiB)
[ 2.753274] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 2.754078] sd 0:0:0:0: [sda] Write Protect is off
[ 2.754832] scsi 3:0:0:0: CD-ROM TSSTcorp CDDVDW SN-208AB FC01 PQ: 0 ANSI: 5
[ 2.755657] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.755668] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.757804] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.758704] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.759607] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 2.827708] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 2.828600] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.829631] hub 1-1:1.0: USB hub found
[ 2.830577] hub 1-1:1.0: 6 ports detected
[ 2.906897] sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 >
[ 2.908086] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.928769] registered taskstats version 1
[ 2.929918] ALSA device list:
[ 2.930772] No soundcards found.
[ 2.943212] usb 2-1: new high-speed USB device number 2 using ehci_hcd
[ 2.965688] kjournald starting. Commit interval 5 seconds
[ 2.965740] EXT3-fs (sda5): mounted filesystem with writeback data mode
[ 2.965746] VFS: Mounted root (ext3 filesystem) readonly on device 8:5.
[ 2.986497] devtmpfs: mounted
[ 2.987374] Freeing unused kernel memory: 372k freed
[ 3.075386] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 3.076290] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.077306] hub 2-1:1.0: USB hub found
[ 3.078251] hub 2-1:1.0: 6 ports detected
[ 3.151039] usb 1-1.3: new high-speed USB device number 3 using ehci_hcd
[ 3.276623] usb 1-1.3: New USB device found, idVendor=04f2, idProduct=b213
[ 3.277538] usb 1-1.3: New USB device strings: Mfr=2, Product=1, SerialNumber=3
[ 3.278405] usb 1-1.3: Product: FJ Camera
[ 3.279270] usb 1-1.3: Manufacturer: Sonix Technology Co., Ltd.
[ 3.280133] usb 1-1.3: SerialNumber: SN0001
[ 3.283036] uvcvideo: Found UVC 1.00 device FJ Camera (04f2:b213)
[ 3.293457] input: FJ Camera as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input5
[ 3.366757] usb 2-1.2: new low-speed USB device number 3 using ehci_hcd
[ 3.462008] usb 2-1.2: New USB device found, idVendor=0461, idProduct=4d20
[ 3.462987] usb 2-1.2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 3.463891] usb 2-1.2: Product: USB Optical Mouse
[ 3.467189] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input6
[ 3.468145] hid-generic 0003:0461:4D20.0001: input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1d.0-1.2/input0
[ 3.538532] usb 2-1.6: new high-speed USB device number 4 using ehci_hcd
[ 3.892326] usb 2-1.6: New USB device found, idVendor=0bda, idProduct=0138
[ 3.893341] usb 2-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.894295] usb 2-1.6: Product: USB2.0-CRW
[ 3.895228] usb 2-1.6: Manufacturer: Generic
[ 3.896149] usb 2-1.6: SerialNumber: 20090516388200000
[ 4.319631] EXT3-fs (sda5): using internal journal
[ 5.083366] udevd[93]: starting version 182
[ 5.378272] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x23
[ 5.525501] input: Fujitsu FUJ02B1 as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:01/FUJ02B1:00/input/input7
[ 5.526976] hda_codec: ALC269VB: SKU not ready 0x90970130
[ 5.527608] fujitsu_laptop: ACPI: Fujitsu FUJ02B1 [FJEX] (on)
[ 5.527777] input: Fujitsu FUJ02E3 as /devices/LNXSYSTM:00/LNXSYBUS:00/FUJ02E3:00/input/input8
[ 5.528329] fujitsu_laptop: ACPI: Fujitsu FUJ02E3 [FEXT] (on)
[ 5.528428] fujitsu_laptop: BTNI: [0x80001]
[ 5.528481] fujitsu_laptop: driver 0.6.0 successfully loaded
[ 5.532532] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 5.532820] r8169 0000:07:00.0 eth0: RTL8168e/8111e at 0xf841c000, 5c:9a:d8:5c:63:31, XID 0c200000 IRQ 17
[ 5.532822] r8169 0000:07:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 5.752278] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x23
[ 5.914907] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x23
[ 5.920413] microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x23
[ 5.926595] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[ 6.196068] Initializing USB Mass Storage driver...
[ 6.197172] scsi6 : usb-storage 2-1.6:1.0
[ 6.198261] usbcore: registered new interface driver usb-storage
[ 6.199272] USB Mass Storage support registered.
[ 6.554409] r8169 0000:07:00.0 eth0: link down
[ 6.555360] r8169 0000:07:00.0 eth0: link down
[ 7.196560] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
[ 7.203146] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 7.910425] microcode: CPU0 updated to revision 0x25, date = 2011-10-11
[ 7.911814] microcode: CPU1 updated to revision 0x25, date = 2011-10-11
[ 7.913586] microcode: CPU2 updated to revision 0x25, date = 2011-10-11
[ 7.914919] microcode: CPU3 updated to revision 0x25, date = 2011-10-11
[ 8.126477] r8169 0000:07:00.0 eth0: link up
[ 8.392416] kjournald starting. Commit interval 5 seconds
[ 8.392442] EXT3-fs (sda8): warning: maximal mount count reached, running e2fsck is recommended
[ 8.392558] EXT3-fs (sda8): using internal journal
[ 8.392558] EXT3-fs (sda8): mounted filesystem with writeback data mode
[ 8.421945] kjournald starting. Commit interval 5 seconds
[ 8.421985] EXT3-fs (sda9): warning: maximal mount count reached, running e2fsck is recommended
[ 8.422104] EXT3-fs (sda9): using internal journal
[ 8.422104] EXT3-fs (sda9): mounted filesystem with writeback data mode
[ 8.448634] kjournald starting. Commit interval 5 seconds
[ 8.448801] EXT3-fs (sda10): using internal journal
[ 8.448802] EXT3-fs (sda10): mounted filesystem with writeback data mode
[ 8.534607] Adding 8191996k swap on /dev/sda6. Priority:-1 extents:1 across:8191996k
[ 19.053917] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
