On 2012/9/18 2:15, Giridhar Malavali wrote: > > > On 9/17/12 5:06 AM, "Yijing Wang" <wangyijing@xxxxxxxxxx> wrote: > >> [ 769.531289] qla2xxx [0000:08:00.0]-001d: : Found an ISP2532 irq 32 >> iobase 0xffffc90016bcc000. >> [ 769.531748] qla2xxx 0000:08:00.0: irq 91 for MSI/MSI-X >> [ 769.531768] qla2xxx 0000:08:00.0: irq 92 for MSI/MSI-X >> [ 799.503673] qla2xxx [0000:08:00.0]-d008:10: No buffer available for >> dump. >> [ 799.503682] qla2xxx [0000:08:00.0]-101c:10: Mailbox cmd timeout >> occurred, cmd=0xb, mb[0]=0xb, eeh_busy=0x0. Scheduling ISP abort. >> [ 799.503689] qla2xxx [0000:08:00.0]-0098:10: Failed to load segment 0 >> of firmware. >> [ 829.853242] qla2xxx [0000:08:00.0]-d008:10: No buffer available for >> dump. >> [ 829.853249] qla2xxx [0000:08:00.0]-008f:10: Failed to load segment 0 >> of firmware. >> [ 829.853253] qla2xxx [0000:08:00.0]-00cf:10: Setup chip ****FAILED****. >> [ 829.853258] qla2xxx [0000:08:00.0]-00d6:10: Failed to initialize >> adapter - Adapter flags 2. >> [ 829.853893] qla2xxx 0000:08:00.1: enabling device (0104 -> 0106) >> [ 829.855251] qla2xxx [0000:08:00.1]-001d: : Found an ISP2532 irq 42 >> iobase 0xffffc90016b88000. >> [ 829.855828] qla2xxx 0000:08:00.1: irq 91 for MSI/MSI-X >> [ 829.855849] qla2xxx 0000:08:00.1: irq 92 for MSI/MSI-X >> [ 859.827388] qla2xxx [0000:08:00.1]-d008:11: No buffer available for >> dump. >> [ 859.827395] qla2xxx [0000:08:00.1]-101c:11: Mailbox cmd timeout >> occurred, cmd=0xb, mb[0]=0xb, eeh_busy=0x0. Scheduling ISP abort. >> [ 859.827400] qla2xxx [0000:08:00.1]-0098:11: Failed to load segment 0 >> of firmware. >> [ 890.176829] qla2xxx [0000:08:00.1]-d008:11: No buffer available for >> dump. >> [ 890.176837] qla2xxx [0000:08:00.1]-008f:11: Failed to load segment 0 >> of firmware. >> [ 890.176841] qla2xxx [0000:08:00.1]-00cf:11: Setup chip ****FAILED****. >> [ 890.176845] qla2xxx [0000:08:00.1]-00d6:11: Failed to initialize >> adapter - Adapter flags 2. > > I see that the one of the initial mailbox which loads data from system > memory to RISC RAM failing causing the probe to fail. > > -- Giri > Hi Giri, Thanks for your comments very much! Because I hot-add FC card in empty slot is ok, so I think maybe FC card and driver have no problem(I'm not sure). So I want to know what hardware(or other) problem may result mailbox loads data from system memory to RISC RAM fail? Thanks Yijing > > > > . > -- Thanks! Yijing -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html