On Thu, Dec 12, 2024 at 12:29:16PM -0500, Frank Li wrote:
> On Thu, Dec 12, 2024 at 05:46:09PM +0100, Lorenzo Pieralisi wrote:
> > On Tue, Dec 10, 2024 at 05:48:59PM -0500, Frank Li wrote:
> > > For the i.MX95, configuration of a LUT is necessary to convert Bus Device
> > > Function (BDF) to stream IDs, which are utilized by both IOMMU and ITS.
> > > This involves checking msi-map and iommu-map device tree properties to
> > > ensure consistent mapping of PCI BDF to the same stream IDs. Subsequently,
> > > LUT-related registers are configured. In the absence of an msi-map, the
> > > built-in MSI controller is utilized as a fallback.
> >
> > This is wrong information. What you want to say is that if an msi-map
> > isn't detected this means that the platform relies on DWC built-in
> > controller for MSIs (that does not need streamIDs handling).
> >
> > That's quite different from what you are writing here.
>
> How about ?
>
> "If an msi-map isn't detected, platform relies on DWC built-in controller
> for MSIs that does not need streamdIDs"
Right. Question: what happens if DT shows that there are SMMU and/or
ITS bindings/mappings but the SMMU driver and ITS driver are either not
enabled or have not probed ?
I assume the LUT programming makes no difference (it is useless yes but
should be harmless too) in this case but wanted to check with you.
Thanks,
Lorenzo
>
> >
> > >
> > > Register a PCI bus callback function to handle enable_device() and
> > > disable_device() operations, setting up the LUT whenever a new PCI device
> > > is enabled.
> > >
> > > Acked-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> > > Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
>
> [...]
>
> > > + int err_i, err_m;
> > > + u32 sid;
> > > +
> > > + dev = imx_pcie->pci->dev;
> > > +
> > > + target = NULL;
> > > + err_i = of_map_id(dev->of_node, rid, "iommu-map", "iommu-map-mask", &target, &sid_i);
> > > + if (target) {
> > > + of_node_put(target);
> > > + } else {
> > > + /*
> > > + * "target == NULL && err_i == 0" means use 1:1 map RID to
> >
> > Is it what it means ? Or does it mean that the iommu-map property was found
> > and RID is out of range ?
>
> yes, if this happen, sid_i will be equal to RID.
>
> >
> > Could you point me at a sample dts for this host bridge please ?
>
> https://github.com/nxp-imx/linux-imx/blob/lf-6.6.y/arch/arm64/boot/dts/freescale/imx95.dtsi
>
> /* 0x10~0x17 stream id for pci0 */
> iommu-map = <0x000 &smmu 0x10 0x1>,
> <0x100 &smmu 0x11 0x7>;
>
> /* msi part */
> msi-map = <0x000 &its 0x10 0x1>,
> <0x100 &its 0x11 0x7>;
>
> >
> > > + * stream ID. Hardware can't support this because stream ID
> > > + * only 5bits
> >
> > It is 5 or 6 bits ? From GENMASK(5, 0) above it should be 6.
>
> Sorry for typo. it is 6bits.
>
> >
> > > + */
> > > + err_i = -EINVAL;
> > > + }
> > > +
> > > + target = NULL;
> > > + err_m = of_map_id(dev->of_node, rid, "msi-map", "msi-map-mask", &target, &sid_m);
> > > +
> > > + /*
> > > + * err_m target
> > > + * 0 NULL Use 1:1 map RID to stream ID,
> >
> > Again, is that what it really means ?
> >
> > > + * Current hardware can't support it,
> > > + * So return -EINVAL.
> > > + * != 0 NULL msi-map not exist, use built-in MSI.
> >
> > does not exist.
> >
> > > + * 0 != NULL Get correct streamID from RID.
> > > + * != 0 != NULL Unexisted case, never happen.
> >
> > "Invalid combination"
> >
> > > + */
> > > + if (!err_m && !target)
> > > + return -EINVAL;
> > > + else if (target)
> > > + of_node_put(target); /* Find stream ID map entry for RID in msi-map */
> > > +
> > > + /*
> > > + * msi-map iommu-map
> > > + * N N DWC MSI Ctrl
> > > + * Y Y ITS + SMMU, require the same sid
> > > + * Y N ITS
> > > + * N Y DWC MSI Ctrl + SMMU
> > > + */
> > > + if (err_i && err_m)
> > > + return 0;
> > > +
> > > + if (!err_i && !err_m) {
> > > + /*
> > > + * MSI glue layer auto add 2 bits controller ID ahead of stream
> >
> > What's "MSI glue layer" ?
>
> It is common term for IC desgin, which connect IP's signal to platform with
> some simple logic. Inside chip, when connect LUT output 6bit streamIDs
> to MSI controller, there are 2bits hardcode controller ID information
> append to 6 bits streamID.
>
> Glue Layer
> <==========>
> ┌─────┐ ┌──────────┐
> │ LUT │ 6bit stream ID │ │
> │ ┼─────────────────►│ MSI │
> └─────┘ 2bit ctrl ID │ │
> ┌───────────►│ │
> │ │ │
> 00 PCIe0 │ │ │
> 01 ENETC │ │ │
> 10 PCIe1 │ │ │
> │ └──────────┘
>
> >
> > > + * ID, so mask this 2bits to get stream ID.
> > > + * But IOMMU glue layer doesn't do that.
> >
> > and "IOMMU glue layer" ?
>
> See above.
>
> Frank
>
> >
> > > + */
> > > + if (sid_i != (sid_m & IMX95_SID_MASK)) {
> > > + dev_err(dev, "iommu-map and msi-map entries mismatch!\n");
> > > + return -EINVAL;
> > > + }
> > > + }
> > > +
> > > + sid = sid_i;
> >
> > err_i could be != 0 here, I understand that the end result is
> > fine given how the code is written but it is misleading.
> >
> > if (!err_i)
> > else if (!err_m)
>
> Okay
>
> >
> > > + if (!err_m)
> > > + sid = sid_m & IMX95_SID_MASK;
> > > +
> > > + return imx_pcie_add_lut(imx_pcie, rid, sid);
> > > +}
> > > +
> > > +static void imx_pcie_disable_device(struct pci_host_bridge *bridge, struct pci_dev *pdev)
> > > +{
> > > + struct imx_pcie *imx_pcie;
> > > +
> > > + imx_pcie = to_imx_pcie(to_dw_pcie_from_pp(bridge->sysdata));
> > > + imx_pcie_remove_lut(imx_pcie, pci_dev_id(pdev));
> > > +}
> > > +
> > > static int imx_pcie_host_init(struct dw_pcie_rp *pp)
> > > {
> > > struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> > > @@ -946,6 +1122,11 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
> > > }
> > > }
> > >
> > > + if (pp->bridge && imx_check_flag(imx_pcie, IMX_PCIE_FLAG_HAS_LUT)) {
> > > + pp->bridge->enable_device = imx_pcie_enable_device;
> > > + pp->bridge->disable_device = imx_pcie_disable_device;
> > > + }
> > > +
> > > imx_pcie_assert_core_reset(imx_pcie);
> > >
> > > if (imx_pcie->drvdata->init_phy)
> > > @@ -1330,6 +1511,8 @@ static int imx_pcie_probe(struct platform_device *pdev)
> > > imx_pcie->pci = pci;
> > > imx_pcie->drvdata = of_device_get_match_data(dev);
> > >
> > > + mutex_init(&imx_pcie->lock);
> > > +
> > > /* Find the PHY if one is defined, only imx7d uses it */
> > > np = of_parse_phandle(node, "fsl,imx7d-pcie-phy", 0);
> > > if (np) {
> > > @@ -1627,7 +1810,8 @@ static const struct imx_pcie_drvdata drvdata[] = {
> > > },
> > > [IMX95] = {
> > > .variant = IMX95,
> > > - .flags = IMX_PCIE_FLAG_HAS_SERDES,
> > > + .flags = IMX_PCIE_FLAG_HAS_SERDES |
> > > + IMX_PCIE_FLAG_HAS_LUT,
> > > .clk_names = imx8mq_clks,
> > > .clks_cnt = ARRAY_SIZE(imx8mq_clks),
> > > .ltssm_off = IMX95_PE0_GEN_CTRL_3,
> > >
> > > --
> > > 2.34.1
> > >
