> -----Original Message-----
> From: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
> Sent: 2024年11月15日 14:41
> To: Hongxing Zhu <hongxing.zhu@xxxxxxx>
> Cc: l.stach@xxxxxxxxxxxxxx; bhelgaas@xxxxxxxxxx; lpieralisi@xxxxxxxxxx;
> kw@xxxxxxxxx; robh@xxxxxxxxxx; krzk+dt@xxxxxxxxxx; conor+dt@xxxxxxxxxx;
> shawnguo@xxxxxxxxxx; Frank Li <frank.li@xxxxxxx>;
> s.hauer@xxxxxxxxxxxxxx; festevam@xxxxxxxxx; imx@xxxxxxxxxxxxxxx;
> kernel@xxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx;
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx;
> linux-kernel@xxxxxxxxxxxxxxx
> Subject: Re: [PATCH v6 03/10] PCI: imx6: Fetch dbi2 and iATU base addesses
> from DT
>
> On Fri, Nov 01, 2024 at 03:06:03PM +0800, Richard Zhu wrote:
> > Since dbi2 and atu regs are added for i.MX8M PCIes. Fetch the dbi2 and
> > iATU base addresses from DT directly, and remove the useless codes.
> >
>
> It'd be useful to mention where the base addresses were extraced. Like by
> the DWC common driver.
You're right. How about change them to the below one?
The dw_pcie_get_resources() function of DWC core codes can fetch the dbi2 and
iATU base addresses from DT directly, and remove the useless codes here.
>
> > Upsteam dts's have not enabled EP function. So no function broken for
> > old upsteam's dtb.
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
>
> Reviewed-by: Manivannan Sadhasivam
> <manivannan.sadhasivam@xxxxxxxxxx>
>
> - Mani
>
> > ---
> > drivers/pci/controller/dwc/pci-imx6.c | 20 --------------------
> > 1 file changed, 20 deletions(-)
> >
> > diff --git a/drivers/pci/controller/dwc/pci-imx6.c
> > b/drivers/pci/controller/dwc/pci-imx6.c
> > index bc8567677a67..462decd1d589 100644
> > --- a/drivers/pci/controller/dwc/pci-imx6.c
> > +++ b/drivers/pci/controller/dwc/pci-imx6.c
> > @@ -1115,7 +1115,6 @@ static int imx_add_pcie_ep(struct imx_pcie
> *imx_pcie,
> > struct platform_device *pdev)
> > {
> > int ret;
> > - unsigned int pcie_dbi2_offset;
> > struct dw_pcie_ep *ep;
> > struct dw_pcie *pci = imx_pcie->pci;
> > struct dw_pcie_rp *pp = &pci->pp;
> > @@ -1125,25 +1124,6 @@ static int imx_add_pcie_ep(struct imx_pcie
> *imx_pcie,
> > ep = &pci->ep;
> > ep->ops = &pcie_ep_ops;
> >
> > - switch (imx_pcie->drvdata->variant) {
> > - case IMX8MQ_EP:
> > - case IMX8MM_EP:
> > - case IMX8MP_EP:
> > - pcie_dbi2_offset = SZ_1M;
> > - break;
> > - default:
> > - pcie_dbi2_offset = SZ_4K;
> > - break;
> > - }
> > -
> > - pci->dbi_base2 = pci->dbi_base + pcie_dbi2_offset;
> > -
> > - /*
> > - * FIXME: Ideally, dbi2 base address should come from DT. But since only
> IMX95 is defining
> > - * "dbi2" in DT, "dbi_base2" is set to NULL here for that platform alone
> so that the DWC
> > - * core code can fetch that from DT. But once all platform DTs were fixed,
> this and the
> > - * above "dbi_base2" setting should be removed.
> > - */
> > if (device_property_match_string(dev, "reg-names", "dbi2") >= 0)
> > pci->dbi_base2 = NULL;
The check and the NULL assignment of "pci->dbi_base2" should be removed too
refer to FIXME listed above. Would updated in v7 later, Sorry about that.
Best Regards
Richard Zhu
> >
> > --
> > 2.37.1
> >
>
> --
> மணிவண்ணன் சதாசிவம்
