On Tue, Nov 12, 2024 at 05:19:24PM +0100, Christian Bruel wrote:
> Add driver to configure the STM32MP25 SoC PCIe Gen2 controller based on the
> DesignWare PCIe core in endpoint mode.
> Uses the common reference clock provided by the host.
> +++ b/drivers/pci/controller/dwc/Kconfig
> +config PCIE_STM32_EP
> + tristate "STMicroelectronics STM32MP25 PCIe Controller (endpoint mode)"
> + depends on ARCH_STM32 || COMPILE_TEST
> + depends on PCI_ENDPOINT
> + select PCIE_DW_EP
> + help
> + Enables endpoint support for DesignWare core based PCIe controller in found
> + in STM32MP25 SoC.
> +
> + This driver can also be built as a module. If so, the module
> + will be called pcie-stm32-ep.
Move as for the host mode entry.
> +++ b/drivers/pci/controller/dwc/pcie-stm32-ep.c
> +static const struct of_device_id stm32_pcie_ep_of_match[] = {
> + { .compatible = "st,stm32mp25-pcie-ep" },
> + {},
> +};
Move next to stm32_pcie_ep_driver.
> +static void stm32_pcie_ep_init(struct dw_pcie_ep *ep)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
> + struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
> + enum pci_barno bar;
> +
> + for (bar = BAR_0; bar <= PCI_STD_NUM_BARS; bar++)
Most users just use "bar = 0". BAR_0 is 0, but there's no real
connection with PCI_STD_NUM_BARS, so I think 0 is probably better.
Looks like this should be "bar < PCI_STD_NUM_BARS"?
> + dw_pcie_ep_reset_bar(pci, bar);
> +
> + /* Defer Completion Requests until link started */
Not sure what a Completion Request is. Is this some internal STM or
DWC thing? Or is this related to Request Retry Status completions for
config requests?
> + regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
> + STM32MP25_PCIECR_REQ_RETRY_EN,
> + STM32MP25_PCIECR_REQ_RETRY_EN);
> +}
> +static int stm32_pcie_raise_irq(struct dw_pcie_ep *ep, u8 func_no,
> + unsigned int type, u16 interrupt_num)
> +{
> + struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
> +
> + switch (type) {
> + case PCI_IRQ_INTX:
> + return dw_pcie_ep_raise_intx_irq(ep, func_no);
> + case PCI_IRQ_MSI:
> + return dw_pcie_ep_raise_msi_irq(ep, func_no, interrupt_num);
> + default:
> + dev_err(pci->dev, "UNKNOWN IRQ type\n");
> + return -EINVAL;
> + }
> +
> + return 0;
Is the compiler not smart enough to notice that this is unreachable?
> +static void stm32_pcie_perst_deassert(struct dw_pcie *pci)
> +{
> + struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
> + struct device *dev = pci->dev;
> + struct dw_pcie_ep *ep = &pci->ep;
> + int ret;
> +
> + if (stm32_pcie->link_status == STM32_PCIE_EP_LINK_ENABLED) {
> + dev_dbg(pci->dev, "Link is already enabled\n");
> + return;
> + }
> +
> + dev_dbg(dev, "PERST de-asserted by host. Starting link training\n");
> +
> + ret = pm_runtime_resume_and_get(dev);
> + if (ret < 0) {
> + dev_err(dev, "pm runtime resume failed: %d\n", ret);
> + return;
> + }
> +
> + ret = stm32_pcie_enable_resources(stm32_pcie);
> + if (ret) {
> + dev_err(dev, "Failed to enable resources: %d\n", ret);
> + pm_runtime_put_sync(dev);
> + return;
> + }
> +
> + ret = dw_pcie_ep_init_registers(ep);
> + if (ret) {
> + dev_err(dev, "Failed to complete initialization: %d\n", ret);
> + stm32_pcie_disable_resources(stm32_pcie);
> + pm_runtime_put_sync(dev);
> + return;
> + }
> +
> + pci_epc_init_notify(ep->epc);
> +
> + ret = stm32_pcie_enable_link(pci);
> + if (ret) {
> + dev_err(dev, "PCIe Cannot establish link: %d\n", ret);
> + stm32_pcie_disable_resources(stm32_pcie);
> + pm_runtime_put_sync(dev);
> + return;
> + }
> +
> + stm32_pcie->link_status = STM32_PCIE_EP_LINK_ENABLED;
> +}
> +static int stm32_add_pcie_ep(struct stm32_pcie *stm32_pcie,
> + struct platform_device *pdev)
> +{
> + struct dw_pcie *pci = stm32_pcie->pci;
> + struct dw_pcie_ep *ep = &pci->ep;
> + struct device *dev = &pdev->dev;
> + int ret;
> +
> + ret = regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
> + STM32MP25_PCIECR_TYPE_MASK,
> + STM32MP25_PCIECR_EP);
> + if (ret)
> + return ret;
> +
> + ret = pm_runtime_resume_and_get(dev);
> + if (ret < 0) {
> + dev_err(dev, "pm runtime resume failed: %d\n", ret);
> + return ret;
> + }
> +
> + reset_control_assert(stm32_pcie->rst);
> + reset_control_deassert(stm32_pcie->rst);
> +
> + ep->ops = &stm32_pcie_ep_ops;
> +
> + ret = dw_pcie_ep_init(ep);
> + if (ret) {
> + dev_err(dev, "failed to initialize ep: %d\n", ret);
> + pm_runtime_put_sync(dev);
> + return ret;
> + }
> +
> + ret = stm32_pcie_enable_resources(stm32_pcie);
> + if (ret) {
> + dev_err(dev, "failed to enable resources: %d\n", ret);
> + dw_pcie_ep_deinit(ep);
> + pm_runtime_put_sync(dev);
> + return ret;
> + }
> +
> + ret = dw_pcie_ep_init_registers(ep);
> + if (ret) {
> + dev_err(dev, "Failed to initialize DWC endpoint registers\n");
> + stm32_pcie_disable_resources(stm32_pcie);
> + dw_pcie_ep_deinit(ep);
> + pm_runtime_put_sync(dev);
> + return ret;
> + }
Consider gotos for the error cases with a cleanup block at the end.
There's a fair bit of repetition there as more things get initialized,
and it's error-prone to extend this in the future.
Same applies in stm32_pcie_perst_deassert().
> + pci_epc_init_notify(ep->epc);
> +
> + return 0;
> +}
> +
> +static int stm32_pcie_probe(struct platform_device *pdev)
> +{
> + struct stm32_pcie *stm32_pcie;
> + struct dw_pcie *dw;
> + struct device *dev = &pdev->dev;
> + int ret;
> +
> + stm32_pcie = devm_kzalloc(dev, sizeof(*stm32_pcie), GFP_KERNEL);
> + if (!stm32_pcie)
> + return -ENOMEM;
> +
> + dw = devm_kzalloc(dev, sizeof(*dw), GFP_KERNEL);
> + if (!dw)
> + return -ENOMEM;
Add blank line here.
> + stm32_pcie->pci = dw;
> +static struct platform_driver stm32_pcie_ep_driver = {
> + .probe = stm32_pcie_probe,
> + .remove_new = stm32_pcie_remove,
.remove().
> + .driver = {
> + .name = "stm32-ep-pcie",
> + .of_match_table = stm32_pcie_ep_of_match,
> + },
> +};
