Re: [PATCH v2 5/5] arm64: dts: qcom: x1e80100: Add support for PCIe3 on x1e80100

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Sep 13, 2024 at 01:37:24AM -0700, Qiang Yu wrote:
> Describe PCIe3 controller and PHY. Also add required system resources like
> regulators, clocks, interrupts and registers configuration for PCIe3.
> 
> Signed-off-by: Qiang Yu <quic_qianyu@xxxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/x1e80100.dtsi | 202 ++++++++++++++++++++++++-
>  1 file changed, 201 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/x1e80100.dtsi b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> index a36076e3c56b..a7703e4974a6 100644
> --- a/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> +++ b/arch/arm64/boot/dts/qcom/x1e80100.dtsi
> @@ -744,7 +744,7 @@ gcc: clock-controller@100000 {
>  
>  			clocks = <&bi_tcxo_div2>,
>  				 <&sleep_clk>,
> -				 <0>,
> +				 <&pcie3_phy>,
>  				 <&pcie4_phy>,
>  				 <&pcie5_phy>,
>  				 <&pcie6a_phy>,
> @@ -2907,6 +2907,206 @@ mmss_noc: interconnect@1780000 {
>  			#interconnect-cells = <2>;
>  		};
>  
> +		pcie3: pci@1bd0000 {

pcie@

> +			device_type = "pci";
> +			compatible = "qcom,pcie-x1e80100";
> +			reg = <0 0x01bd0000 0 0x3000>,
> +			      <0 0x78000000 0 0xf1d>,

0x0 here and below.

> +			      <0 0x78000f40 0 0xa8>,
> +			      <0 0x78001000 0 0x1000>,
> +			      <0 0x78100000 0 0x100000>,
> +			      <0 0x01bd3000 0 0x1000>;
> +			reg-names = "parf",
> +				    "dbi",
> +				    "elbi",
> +				    "atu",
> +				    "config",
> +				    "mhi";
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			ranges = <0x01000000 0x0 0x00000000 0x0 0x78200000 0x0 0x100000>,
> +				 <0x02000000 0x0 0x78300000 0x0 0x78300000 0x0 0x3d00000>,
> +				 <0x03000000 0x7 0x40000000 0x7 0x40000000 0x0 0x40000000>;
> +			bus-range = <0x00 0xff>;
> +
> +			dma-coherent;
> +
> +			linux,pci-domain = <3>;
> +			num-lanes = <8>;
> +
> +			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi0",
> +					  "msi1",
> +					  "msi2",
> +					  "msi3",
> +					  "msi4",
> +					  "msi5",
> +					  "msi6",
> +					  "msi7";

Can you add 'global' interrupt as well? While doing so, please make sure the
global_irq related patches are applied and Link up works fine. Those patches are
already in linux-next.

> +
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc 0 0 0 220 IRQ_TYPE_LEVEL_HIGH>,

Use GIC_SPI for the parent interrupt specifier.

- Mani

> +					<0 0 0 2 &intc 0 0 0 221 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 3 &intc 0 0 0 237 IRQ_TYPE_LEVEL_HIGH>,
> +					<0 0 0 4 &intc 0 0 0 238 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			clocks = <&gcc GCC_PCIE_3_AUX_CLK>,
> +				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
> +				 <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
> +				 <&gcc GCC_CFG_NOC_PCIE_ANOC_NORTH_AHB_CLK>,
> +				 <&gcc GCC_CNOC_PCIE_NORTH_SF_AXI_CLK>;
> +			clock-names = "aux",
> +				      "cfg",
> +				      "bus_master",
> +				      "bus_slave",
> +				      "slave_q2a",
> +				      "noc_aggr",
> +				      "cnoc_sf_axi";
> +
> +			assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
> +			assigned-clock-rates = <19200000>;
> +
> +			interconnects = <&pcie_south_anoc MASTER_PCIE_3 QCOM_ICC_TAG_ALWAYS
> +					 &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
> +					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
> +					 &cnoc_main SLAVE_PCIE_3 QCOM_ICC_TAG_ALWAYS>;
> +			interconnect-names = "pcie-mem",
> +					     "cpu-pcie";
> +
> +			resets = <&gcc GCC_PCIE_3_BCR>,
> +				 <&gcc GCC_PCIE_3_LINK_DOWN_BCR>;
> +			reset-names = "pci",
> +				      "link_down";
> +
> +			power-domains = <&gcc GCC_PCIE_3_GDSC>;
> +
> +			phys = <&pcie3_phy>;
> +			phy-names = "pciephy";
> +
> +			operating-points-v2 = <&pcie3_opp_table>;
> +
> +			status = "disabled";
> +
> +			pcie3_opp_table: opp-table {
> +				compatible = "operating-points-v2";
> +
> +				/* GEN 1 x1 */
> +				opp-2500000 {
> +					opp-hz = /bits/ 64 <2500000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <250000 1>;
> +				};
> +
> +				/* GEN 1 x2 and GEN 2 x1 */
> +				opp-5000000 {
> +					opp-hz = /bits/ 64 <5000000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <500000 1>;
> +				};
> +
> +				/* GEN 1 x4 and GEN 2 x2 */
> +				opp-10000000 {
> +					opp-hz = /bits/ 64 <10000000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <1000000 1>;
> +				};
> +
> +				/* GEN 1 x8 and GEN 2 x4 */
> +				opp-20000000 {
> +					opp-hz = /bits/ 64 <20000000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <2000000 1>;
> +				};
> +
> +				/* GEN 2 x8 */
> +				opp-40000000 {
> +					opp-hz = /bits/ 64 <40000000>;
> +					required-opps = <&rpmhpd_opp_low_svs>;
> +					opp-peak-kBps = <4000000 1>;
> +				};
> +
> +				/* GEN 3 x1 */
> +				opp-8000000 {
> +					opp-hz = /bits/ 64 <8000000>;
> +					required-opps = <&rpmhpd_opp_svs>;
> +					opp-peak-kBps = <984500 1>;
> +				};
> +
> +				/* GEN 3 x2 and GEN 4 x1 */
> +				opp-16000000 {
> +					opp-hz = /bits/ 64 <16000000>;
> +					required-opps = <&rpmhpd_opp_svs>;
> +					opp-peak-kBps = <1969000 1>;
> +				};
> +
> +				/* GEN 3 x4 and GEN 4 x2 */
> +				opp-32000000 {
> +					opp-hz = /bits/ 64 <32000000>;
> +					required-opps = <&rpmhpd_opp_svs>;
> +					opp-peak-kBps = <3938000 1>;
> +				};
> +
> +				/* GEN 3 x8 and GEN 4 x4 */
> +				opp-64000000 {
> +					opp-hz = /bits/ 64 <64000000>;
> +					required-opps = <&rpmhpd_opp_svs>;
> +					opp-peak-kBps = <7876000 1>;
> +				};
> +
> +				/* GEN 4 x8 */
> +				opp-128000000 {
> +					opp-hz = /bits/ 64 <128000000>;
> +					required-opps = <&rpmhpd_opp_svs>;
> +					opp-peak-kBps = <15753000 1>;
> +				};
> +			};
> +		};
> +
> +		pcie3_phy: phy@1be0000 {
> +			compatible = "qcom,x1e80100-qmp-gen4x8-pcie-phy";
> +			reg = <0 0x01be0000 0 0x10000>;
> +
> +			clocks = <&gcc GCC_PCIE_3_PHY_AUX_CLK>,
> +				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
> +				 <&tcsr TCSR_PCIE_8L_CLKREF_EN>,
> +				 <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>,
> +				 <&gcc GCC_PCIE_3_PIPE_CLK>,
> +				 <&gcc GCC_PCIE_3_PIPEDIV2_CLK>;
> +			clock-names = "aux",
> +				      "cfg_ahb",
> +				      "ref",
> +				      "rchng",
> +				      "pipe",
> +				      "pipediv2";
> +
> +			resets = <&gcc GCC_PCIE_3_PHY_BCR>,
> +				 <&gcc GCC_PCIE_3_NOCSR_COM_PHY_BCR>;
> +			reset-names = "phy",
> +				      "phy_nocsr";
> +
> +			assigned-clocks = <&gcc GCC_PCIE_3_PHY_RCHNG_CLK>;
> +			assigned-clock-rates = <100000000>;
> +
> +			power-domains = <&gcc GCC_PCIE_3_PHY_GDSC>;
> +
> +			#clock-cells = <0>;
> +			clock-output-names = "pcie3_pipe_clk";
> +
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
>  		pcie6a: pci@1bf8000 {
>  			device_type = "pci";
>  			compatible = "qcom,pcie-x1e80100";
> -- 
> 2.34.1
> 

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux