Re: [PATCH v2 2/6] PCI: kirin: Tidy up _probe() related function with dev_err_probe()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 30 Aug 2024 11:58:15 +0800
Zhang Zekun <zhangzekun11@xxxxxxxxxx> wrote:

> The combination of dev_err() and the returned error code could be
> replaced by dev_err_probe() in driver's probe function. Let's,
> converting to dev_err_probe() to make code more simple.
> 
> Suggested-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>
> Signed-off-by: Zhang Zekun <zhangzekun11@xxxxxxxxxx>
There are a few unnecessarily long lines in here. I'd wrap them.
Otherwise LGTM.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@xxxxxxxxxx>

> ---
>  drivers/pci/controller/dwc/pcie-kirin.c | 36 +++++++++----------------
>  1 file changed, 12 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-kirin.c b/drivers/pci/controller/dwc/pcie-kirin.c
> index e9bda1746ca5..fc0a71575085 100644
> --- a/drivers/pci/controller/dwc/pcie-kirin.c
> +++ b/drivers/pci/controller/dwc/pcie-kirin.c
> @@ -216,10 +216,8 @@ static int hi3660_pcie_phy_start(struct hi3660_pcie_phy *phy)
>  
>  	usleep_range(PIPE_CLK_WAIT_MIN, PIPE_CLK_WAIT_MAX);
>  	reg_val = kirin_apb_phy_readl(phy, PCIE_APB_PHY_STATUS0);
> -	if (reg_val & PIPE_CLK_STABLE) {
> -		dev_err(dev, "PIPE clk is not stable\n");
> -		return -EINVAL;
> -	}
> +	if (reg_val & PIPE_CLK_STABLE)
> +		return dev_err_probe(dev, -EINVAL, "PIPE clk is not stable\n");
>  
>  	return 0;
>  }
> @@ -371,10 +369,8 @@ static int kirin_pcie_get_gpio_enable(struct kirin_pcie *pcie,
>  	if (ret < 0)
>  		return 0;
>  
> -	if (ret > MAX_PCI_SLOTS) {
> -		dev_err(dev, "Too many GPIO clock requests!\n");
> -		return -EINVAL;
> -	}
> +	if (ret > MAX_PCI_SLOTS)
> +		return dev_err_probe(dev, -EINVAL, "Too many GPIO clock requests!\n");
>  
>  	pcie->n_gpio_clkreq = ret;
>  
> @@ -421,16 +417,12 @@ static int kirin_pcie_parse_port(struct kirin_pcie *pcie,
>  			}
>  
>  			pcie->num_slots++;
> -			if (pcie->num_slots > MAX_PCI_SLOTS) {
> -				dev_err(dev, "Too many PCI slots!\n");
> -				return -EINVAL;
> -			}
> +			if (pcie->num_slots > MAX_PCI_SLOTS)
> +				return dev_err_probe(dev, -EINVAL, "Too many PCI slots!\n");

Lines are getting a bit long, I'd wrap after -EINVAL,
Same in other cases.


>  
>  			ret = of_pci_get_devfn(child);
> -			if (ret < 0) {
> -				dev_err(dev, "failed to parse devfn: %d\n", ret);
> -				return ret;
> -			}
> +			if (ret < 0)
> +				return dev_err_probe(dev, ret, "failed to parse devfn\n");
>  
>  			slot = PCI_SLOT(ret);
>  





[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux