Re: [PATCH 3/8] phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 27.08.2024 8:36 AM, Qiang Yu wrote:
> Currently driver supports only x4 lane based functionality using tx/rx and
> tx2/rx2 pair of register sets. To support 8 lane functionality with PCIe3,
> PCIe3 related QMP PHY provides additional programming which are available
> as txz and rxz based register set. Hence adds txz and rxz based registers
> usage and programming sequences. Phy register setting for txz and rxz will
> be applied to all 8 lanes. Some lanes may have different settings on
> several registers than txz/rxz, these registers should be programmed after
> txz/rxz programming sequences completing.
> 
> Besides, PCIe3 related QMP PHY also requires addtional clk, which is named
> as clkref_en. Hence, add this clk into qmp_pciephy_clk_l so that it can be
> easily parsed from devicetree during init.
> 
> Signed-off-by: Qiang Yu <quic_qianyu@xxxxxxxxxxx>
> ---

[...]

> +static const struct qmp_phy_init_tbl x1e80100_qmp_gen4x8_pcie_rx_tbl[] = {
> +	QMP_PHY_INIT_CFG_LANE(QSERDES_V6_20_RX_DFE_CTLE_POST_CAL_OFFSET, 0x3a, 1),

1 -> BIT(0)

[...]

> +	/* Set to true for programming all 8 lanes using txz/rxz registers */
> +	bool lane_broadcasting;

This is unnecessary because you call qmp_configure_lane conditionally,
but that function has a nullcheck built in

> +
>  	/* resets to be requested */
>  	const char * const *reset_list;
>  	int num_resets;
> @@ -2655,6 +2815,8 @@ struct qmp_pcie {
>  	void __iomem *rx;
>  	void __iomem *tx2;
>  	void __iomem *rx2;
> +	void __iomem *txz;
> +	void __iomem *rxz;
>  	void __iomem *ln_shrd;
>  
>  	void __iomem *port_b;
> @@ -2700,7 +2862,7 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
>  
>  /* list of clocks required by phy */
>  static const char * const qmp_pciephy_clk_l[] = {
> -	"aux", "cfg_ahb", "ref", "refgen", "rchng", "phy_aux",
> +	"aux", "cfg_ahb", "ref", "refgen", "rchng", "phy_aux", "clkref_en",

Why not just put in TCSR_PCIE_8L_CLKREF_EN as "ref"? It's downstream
of the XO anyway.

[...]

>  	const struct qmp_phy_cfg *cfg = qmp->cfg;
> @@ -3700,6 +3907,11 @@ static void qmp_pcie_init_registers(struct qmp_pcie *qmp, const struct qmp_phy_c
>  
>  	qmp_configure(qmp->dev, serdes, tbls->serdes, tbls->serdes_num);
>  
> +	if (cfg->lane_broadcasting) {

All these ifs can be unconditional

Konrad




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux