On Sun, 25 Aug 2024, Maciej W. Rozycki wrote:
> When `pcie_failed_link_retrain' has failed to retrain the link by hand
> it leaves the link speed restricted to 2.5GT/s, which will then affect
> any device that has been plugged in later on, which may not suffer from
> the problem that caused the speed restriction to have been attempted.
> Consequently such a downstream device will suffer from an unnecessary
> communication throughput limitation and therefore performance loss.
>
> Remove the speed restriction then and revert the Link Control 2 register
> to its original state if link retraining with the speed restriction in
> place has failed. Retrain the link again afterwards so as to remove any
> residual state, waiting on LT rather than DLLLA to avoid an excessive
> delay and ignoring the result as this training is supposed to fail anyway.
>
> Fixes: a89c82249c37 ("PCI: Work around PCIe link training failures")
> Reported-by: Matthew W Carlis <mattc@xxxxxxxxxxxxxxx>
> Link: https://lore.kernel.org/r/20240806000659.30859-1-mattc@xxxxxxxxxxxxxxx/
> Link: https://lore.kernel.org/r/20240722193407.23255-1-mattc@xxxxxxxxxxxxxxx/
> Signed-off-by: Maciej W. Rozycki <macro@xxxxxxxxxxx>
> Cc: stable@xxxxxxxxxxxxxxx # v6.5+
> ---
> Changes from v2:
>
> - Wait on LT rather than DLLLA with clean-up retraining with the speed
> restriction lifted, so as to avoid an excessive delay as it's supposed
> to fail anyway.
>
> New change in v2.
> ---
> drivers/pci/quirks.c | 11 ++++++++++-
> 1 file changed, 10 insertions(+), 1 deletion(-)
>
> linux-pcie-failed-link-retrain-fail-unclamp.diff
> Index: linux-macro/drivers/pci/quirks.c
> ===================================================================
> --- linux-macro.orig/drivers/pci/quirks.c
> +++ linux-macro/drivers/pci/quirks.c
> @@ -66,7 +66,7 @@
> * apply this erratum workaround to any downstream ports as long as they
> * support Link Active reporting and have the Link Control 2 register.
> * Restrict the speed to 2.5GT/s then with the Target Link Speed field,
> - * request a retrain and wait 200ms for the data link to go up.
> + * request a retrain and check the result.
> *
> * If this turns out successful and we know by the Vendor:Device ID it is
> * safe to do so, then lift the restriction, letting the devices negotiate
> @@ -74,6 +74,10 @@
> * firmware may have already arranged and lift it with ports that already
> * report their data link being up.
> *
> + * Otherwise revert the speed to the original setting and request a retrain
> + * again to remove any residual state, ignoring the result as it's supposed
> + * to fail anyway.
> + *
> * Return TRUE if the link has been successfully retrained, otherwise FALSE.
> */
> bool pcie_failed_link_retrain(struct pci_dev *dev)
> @@ -92,6 +96,8 @@ bool pcie_failed_link_retrain(struct pci
> pcie_capability_read_word(dev, PCI_EXP_LNKSTA, &lnksta);
> if ((lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) ==
> PCI_EXP_LNKSTA_LBMS) {
> + u16 oldlnkctl2 = lnkctl2;
> +
> pci_info(dev, "broken device, retraining non-functional downstream link at 2.5GT/s\n");
>
> lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS;
> @@ -100,6 +106,9 @@ bool pcie_failed_link_retrain(struct pci
>
> if (pcie_retrain_link(dev, false)) {
> pci_info(dev, "retraining failed\n");
> + pcie_capability_write_word(dev, PCI_EXP_LNKCTL2,
> + oldlnkctl2);
> + pcie_retrain_link(dev, true);
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@xxxxxxxxxxxxxxx>
--
i.
