Re: [PATCH] PCI: qcom-ep: Do not enable resources during probe()

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Aug 22, 2024 at 12:31:33PM -0500, Bjorn Helgaas wrote:
> On Thu, Aug 22, 2024 at 09:10:25PM +0530, Manivannan Sadhasivam wrote:
> > On Thu, Aug 22, 2024 at 10:16:58AM -0500, Bjorn Helgaas wrote:
> > > On Thu, Aug 22, 2024 at 12:18:23PM +0530, Manivannan Sadhasivam wrote:
> > > > On Wed, Aug 21, 2024 at 05:56:18PM -0500, Bjorn Helgaas wrote:
> > > > ...
> > > 
> > > > > Although I do have the question of what happens if the RC deasserts
> > > > > PERST# before qcom-ep is loaded.  We probably don't execute
> > > > > qcom_pcie_perst_deassert() in that case, so how does the init happen?
> > > > 
> > > > PERST# is a level trigger signal. So even if the host has asserted
> > > > it before EP booted, the level will stay low and ep will detect it
> > > > while booting.
> > > 
> > > The PERST# signal itself is definitely level oriented.
> > > 
> > > I'm still skeptical about the *interrupt* from the PCIe controller
> > > being level-triggered, as I mentioned here:
> > > https://lore.kernel.org/r/20240815224735.GA57931@bhelgaas
> > 
> > Sorry, that comment got buried into my inbox. So didn't get a chance
> > to respond.
> > 
> > > tegra194 is also dwc-based and has a similar PERST# interrupt but
> > > it's edge-triggered (tegra_pcie_ep_pex_rst_irq()), which I think
> > > is a cleaner implementation.  Then you don't have to remember the
> > > current state, switch between high and low trigger, worry about
> > > races and missing a pulse, etc.
> > 
> > I did try to mimic what tegra194 did when I wrote the qcom-ep
> > driver, but it didn't work. If we use the level triggered interrupt
> > as edge, the interrupt will be missed if we do not listen at the
> > right time (when PERST# goes from high to low and vice versa).
> > 
> > I don't know how tegra194 interrupt controller is wired up, but IIUC
> > they will need to boot the endpoint first and then host to catch the
> > PERST# interrupt.  Otherwise, the endpoint will never see the
> > interrupt until host toggles it again.
> 
> Having to control the boot ordering of endpoint and host is definitely
> problematic.
> 
> What is the nature of the crash when we try to enable the PHY when
> Refclk is not available?  The endpoint has no control over when the
> host asserts/deasserts PERST#.  If PERST# happens to be asserted while
> the endpoint is enabling the PHY, and this causes some kind of crash
> that the endpoint driver can't easily recover from, that's a serious
> robustness problem.
> 

The whole endpoint SoC crashes if the refclk is not available during
phy_power_on() as the PHY driver tries to access some register on Dmitry's
platform (I did not see this crash on SM8450 SoC though).

If we keep the enable_resources() during probe() then the race condition you
observed above could apply. So removing that from probe() will also make the
race condition go away,

- Mani

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux