Native PCIe Enclosure Management (NPEM, PCIe r6.1 sec 6.28) allows managing LED in storage enclosures. NPEM is indication oriented and it does not give direct access to LED. Although each of the indications *could* represent an individual LED, multiple indications could also be represented as a single, multi-color LED or a single LED blinking in a specific interval. The specification leaves that open. Each enabled indication (capability register bit on) is represented as a ledclass_dev which can be controlled through sysfs. For every ledclass device only 2 brightness states are allowed: LED_ON (1) or LED_OFF (0). It is corresponding to NPEM control register (Indication bit on/off). Ledclass devices appear in sysfs as child devices (subdirectory) of PCI device which has an NPEM Extended Capability and indication is enabled in NPEM capability register. For example, these are leds created for pcieport "10000:02:05.0" on my setup: leds/ ├── 10000:02:05.0:enclosure:fail ├── 10000:02:05.0:enclosure:locate ├── 10000:02:05.0:enclosure:ok └── 10000:02:05.0:enclosure:rebuild They can be also found in "/sys/class/leds" directory. Parent PCIe device bdf is used to guarantee uniqueness across leds subsystem. To enable/disable fail indication "brightness" file can be edited: echo 1 > ./leds/10000:02:05.0:enclosure:fail/brightness echo 0 > ./leds/10000:02:05.0:enclosure:fail/brightness PCIe r6.1, sec 7.9.19.2 defines the possible indications. Multiple indications for same parent PCIe device can conflict and hardware may update them when processing new request. To avoid issues, driver refresh all indications by reading back control register. Driver is projected to be exclusive NPEM extended capability manager. It waits up to 1 second after imposing new request, it doesn't verify if controller is busy before write, assuming that mutex lock gives protection from concurrent updates. Driver is not registered if _DSM LED management is available. NPEM is a PCIe extended capability so it should be registered in pcie_init_capabilities() but it is not possible due to LED dependency. Parent pci_device must be added earlier for led_classdev_register() to be successful. NPEM does not require configuration on kernel side, it is safe to register LED devices later. Link: https://members.pcisig.com/wg/PCI-SIG/document/19849 [1] Suggested-by: Lukas Wunner <lukas@xxxxxxxxx> Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@xxxxxxxxxxxxxxx> --- drivers/pci/Kconfig | 9 + drivers/pci/Makefile | 1 + drivers/pci/npem.c | 410 ++++++++++++++++++++++++++++++++++ drivers/pci/pci.h | 8 + drivers/pci/probe.c | 2 + drivers/pci/remove.c | 2 + include/linux/pci.h | 3 + include/uapi/linux/pci_regs.h | 34 +++ 8 files changed, 469 insertions(+) create mode 100644 drivers/pci/npem.c diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig index d35001589d88..e696e69ad516 100644 --- a/drivers/pci/Kconfig +++ b/drivers/pci/Kconfig @@ -143,6 +143,15 @@ config PCI_IOV If unsure, say N. +config PCI_NPEM + bool "Native PCIe Enclosure Management" + depends on LEDS_CLASS=y + help + Support for Native PCIe Enclosure Management. It allows managing LED + indications in storage enclosures. Enclosure must support following + indications: OK, Locate, Fail, Rebuild, other indications are + optional. + config PCI_PRI bool "PCI PRI support" select PCI_ATS diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile index 175302036890..cd5f655d4be9 100644 --- a/drivers/pci/Makefile +++ b/drivers/pci/Makefile @@ -34,6 +34,7 @@ obj-$(CONFIG_XEN_PCIDEV_FRONTEND) += xen-pcifront.o obj-$(CONFIG_VGA_ARB) += vgaarb.o obj-$(CONFIG_PCI_DOE) += doe.o obj-$(CONFIG_PCI_DYNAMIC_OF_NODES) += of_property.o +obj-$(CONFIG_PCI_NPEM) += npem.o # Endpoint library must be initialized before its users obj-$(CONFIG_PCI_ENDPOINT) += endpoint/ diff --git a/drivers/pci/npem.c b/drivers/pci/npem.c new file mode 100644 index 000000000000..a76a2044dab2 --- /dev/null +++ b/drivers/pci/npem.c @@ -0,0 +1,410 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * PCIe Enclosure management driver created for LED interfaces based on + * indications. It says *what indications* blink but does not specify *how* + * they blink - it is hardware defined. + * + * The driver name refers to Native PCIe Enclosure Management. It is + * first indication oriented standard with specification. + * + * Native PCIe Enclosure Management (NPEM) + * PCIe Base Specification r6.1 sec 6.28 + * PCIe Base Specification r6.1 sec 7.9.19 + * + * Copyright (c) 2023-2024 Intel Corporation + * Mariusz Tkaczyk <mariusz.tkaczyk@xxxxxxxxxxxxxxx> + */ + +#include <linux/acpi.h> +#include <linux/bitops.h> +#include <linux/errno.h> +#include <linux/iopoll.h> +#include <linux/leds.h> +#include <linux/mutex.h> +#include <linux/pci.h> +#include <linux/pci_regs.h> +#include <linux/types.h> +#include <linux/uleds.h> + +#include "pci.h" + +struct indication { + u32 bit; + const char *name; +}; + +static const struct indication npem_indications[] = { + {PCI_NPEM_IND_OK, "enclosure:ok"}, + {PCI_NPEM_IND_LOCATE, "enclosure:locate"}, + {PCI_NPEM_IND_FAIL, "enclosure:fail"}, + {PCI_NPEM_IND_REBUILD, "enclosure:rebuild"}, + {PCI_NPEM_IND_PFA, "enclosure:pfa"}, + {PCI_NPEM_IND_HOTSPARE, "enclosure:hotspare"}, + {PCI_NPEM_IND_ICA, "enclosure:ica"}, + {PCI_NPEM_IND_IFA, "enclosure:ifa"}, + {PCI_NPEM_IND_IDT, "enclosure:idt"}, + {PCI_NPEM_IND_DISABLED, "enclosure:disabled"}, + {PCI_NPEM_IND_SPEC_0, "enclosure:specific_0"}, + {PCI_NPEM_IND_SPEC_1, "enclosure:specific_1"}, + {PCI_NPEM_IND_SPEC_2, "enclosure:specific_2"}, + {PCI_NPEM_IND_SPEC_3, "enclosure:specific_3"}, + {PCI_NPEM_IND_SPEC_4, "enclosure:specific_4"}, + {PCI_NPEM_IND_SPEC_5, "enclosure:specific_5"}, + {PCI_NPEM_IND_SPEC_6, "enclosure:specific_6"}, + {PCI_NPEM_IND_SPEC_7, "enclosure:specific_7"}, + {0, NULL} +}; + +#define for_each_indication(ind, inds) \ + for (ind = inds; ind->bit; ind++) + +/* To avoid confusion, do not keep any special bits in indications */ +static u32 reg_to_indications(u32 caps, const struct indication *inds) +{ + const struct indication *ind; + u32 supported_indications = 0; + + for_each_indication(ind, inds) + supported_indications |= ind->bit; + + return caps & supported_indications; +} + +/** + * struct npem_led - LED details + * @indication: indication details + * @npem: npem device + * @name: LED name + * @led: LED device + */ +struct npem_led { + const struct indication *indication; + struct npem *npem; + char name[LED_MAX_NAME_SIZE]; + struct led_classdev led; +}; + +/** + * struct npem_ops - backend specific callbacks + * @inds: supported indications array + * @get_active_indications: get active indications + * npem: npem device + * buf: response buffer + * @set_active_indications: set new indications + * npem: npem device + * val: bit mask to set + * + * Handle communication with hardware. set_active_indications updates + * npem->active_indications. + */ +struct npem_ops { + const struct indication *inds; + int (*get_active_indications)(struct npem *npem, u32 *buf); + int (*set_active_indications)(struct npem *npem, u32 val); +}; + +/** + * struct npem - NPEM device properties + * @dev: PCIe device this driver is attached to + * @ops: Backend specific callbacks + * @npem_lock: to keep concurrent updates serialized + * @pos: NPEM capability offset (only relevant for NPEM direct register access, + * not DSM access method) + * @supported_indications: bit mask of supported indications + * non-indication and reserved bits are cleared + * @active_indications: bit mask of active indications + * non-indication and reserved bits are cleared + * @led_cnt: Supported LEDs count + * @leds: supported LEDs + */ +struct npem { + struct pci_dev *dev; + const struct npem_ops *ops; + struct mutex npem_lock; + u16 pos; + u32 supported_indications; + u32 active_indications; + int led_cnt; + struct npem_led leds[]; +}; + +static int npem_read_reg(struct npem *npem, u16 reg, u32 *val) +{ + int ret = pci_read_config_dword(npem->dev, npem->pos + reg, val); + + return pcibios_err_to_errno(ret); +} + +static int npem_write_ctrl(struct npem *npem, u32 reg) +{ + int pos = npem->pos + PCI_NPEM_CTRL; + int ret = pci_write_config_dword(npem->dev, pos, reg); + + return pcibios_err_to_errno(ret); +} + +static int npem_get_active_indications(struct npem *npem, u32 *buf) +{ + int ret; + + ret = npem_read_reg(npem, PCI_NPEM_CTRL, buf); + if (ret) + return ret; + + /* If PCI_NPEM_CTRL_ENABLE is not set then no indication should blink */ + if (!(*buf & PCI_NPEM_CTRL_ENABLE)) + *buf = 0; + + /* Filter out not supported indications in response */ + *buf &= npem->supported_indications; + return 0; +} + +static int npem_set_active_indications(struct npem *npem, u32 val) +{ + int ret, ret_val; + u32 cc_status; + + lockdep_assert_held(&npem->npem_lock); + + /* This bit is always required */ + val |= PCI_NPEM_CTRL_ENABLE; + ret = npem_write_ctrl(npem, val); + if (ret) + return ret; + + /* + * For the case where a NPEM command has not completed immediately, + * it is recommended that software not continuously “spin” on polling + * the status register, but rather poll under interrupt at a reduced + * rate; for example at 10 ms intervals. + * + * PCIe r6.1 sec 6.28 "Implementation Note: Software Polling of NPEM + * Command Completed" + */ + ret = read_poll_timeout(npem_read_reg, ret_val, + ret_val || (cc_status & PCI_NPEM_STATUS_CC), + 10 * USEC_PER_MSEC, USEC_PER_SEC, false, npem, + PCI_NPEM_STATUS, &cc_status); + if (ret) + return ret_val; + + /* + * All writes to control register, including writes that do not change + * the register value, are NPEM commands and should eventually result + * in a command completion indication in the NPEM Status Register. + * + * PCIe Base Specification r6.1 sec 7.9.19.3 + * + * Register may not be updated, or other conflicting bits may be + * cleared. Spec is not strict here. Read NPEM Control register after + * write to keep cache in-sync. + */ + return npem_get_active_indications(npem, &npem->active_indications); +} + +static const struct npem_ops npem_ops = { + .inds = npem_indications, + .get_active_indications = npem_get_active_indications, + .set_active_indications = npem_set_active_indications, +}; + +#define DSM_GUID GUID_INIT(0x5d524d9d, 0xfff9, 0x4d4b, 0x8c, 0xb7, 0x74, 0x7e,\ + 0xd5, 0x1e, 0x19, 0x4d) +#define GET_SUPPORTED_STATES_DSM BIT(1) +#define GET_STATE_DSM BIT(2) +#define SET_STATE_DSM BIT(3) + +static const guid_t dsm_guid = DSM_GUID; + +static bool npem_has_dsm(struct pci_dev *pdev) +{ + acpi_handle handle; + + handle = ACPI_HANDLE(&pdev->dev); + if (!handle) + return false; + + return acpi_check_dsm(handle, &dsm_guid, 0x1, GET_SUPPORTED_STATES_DSM | + GET_STATE_DSM | SET_STATE_DSM); +} + +/* + * This function does not use ops->get_active_indications(). + * It returns cached value, npem->npem_lock is held and it is safe. + */ +static enum led_brightness brightness_get(struct led_classdev *led) +{ + struct npem_led *nled = container_of(led, struct npem_led, led); + struct npem *npem = nled->npem; + int ret, val = LED_OFF; + + ret = mutex_lock_interruptible(&npem->npem_lock); + if (ret) + return ret; + + if (npem->active_indications & nled->indication->bit) + val = LED_ON; + + mutex_unlock(&npem->npem_lock); + + return val; +} + +static int brightness_set(struct led_classdev *led, + enum led_brightness brightness) +{ + struct npem_led *nled = container_of(led, struct npem_led, led); + struct npem *npem = nled->npem; + u32 indications; + int ret; + + ret = mutex_lock_interruptible(&npem->npem_lock); + if (ret) + return ret; + + if (brightness == LED_OFF) + indications = npem->active_indications & ~(nled->indication->bit); + else + indications = npem->active_indications | nled->indication->bit; + + ret = npem->ops->set_active_indications(npem, indications); + + mutex_unlock(&npem->npem_lock); + return ret; +} + +static void npem_free(struct npem *npem) +{ + struct npem_led *nled; + int cnt; + + for (cnt = 0; cnt < npem->led_cnt; cnt++) { + nled = &npem->leds[cnt]; + + if (nled->name[0]) + led_classdev_unregister(&nled->led); + } + + mutex_destroy(&npem->npem_lock); + kfree(npem); +} + +static int pci_npem_set_led_classdev(struct npem *npem, struct npem_led *nled) +{ + struct led_classdev *led = &nled->led; + struct led_init_data init_data = {}; + char *name = nled->name; + int ret; + + init_data.devicename = pci_name(npem->dev); + init_data.default_label = nled->indication->name; + + ret = led_compose_name(&npem->dev->dev, &init_data, name); + if (ret) + return ret; + + led->name = name; + led->brightness_set_blocking = brightness_set; + led->brightness_get = brightness_get; + led->max_brightness = LED_ON; + led->default_trigger = "none"; + led->flags = 0; + + ret = led_classdev_register(&npem->dev->dev, led); + if (ret) + /* Clear the name to indicate that it is not registered. */ + name[0] = 0; + return ret; +} + +static int pci_npem_init(struct pci_dev *dev, const struct npem_ops *ops, + int pos, u32 caps) +{ + u32 supported = reg_to_indications(caps, ops->inds); + int supported_cnt = hweight32(supported); + const struct indication *indication; + struct npem_led *nled; + struct npem *npem; + int led_idx = 0; + u32 active; + int ret; + + npem = kzalloc(struct_size(npem, leds, supported_cnt), GFP_KERNEL); + + if (!npem) + return -ENOMEM; + + npem->supported_indications = supported; + npem->led_cnt = supported_cnt; + npem->pos = pos; + npem->dev = dev; + npem->ops = ops; + + ret = ops->get_active_indications(npem, &active); + if (ret) { + npem_free(npem); + return -EACCES; + } + + npem->active_indications = reg_to_indications(active, ops->inds); + + /* + * Do not take npem->npem_lock, get_brightness() is called on + * registration path. + */ + mutex_init(&npem->npem_lock); + + for_each_indication(indication, npem_indications) { + if ((npem->supported_indications & indication->bit) == 0) + /* Do not register unsupported indication */ + continue; + + nled = &npem->leds[led_idx++]; + nled->indication = indication; + nled->npem = npem; + + ret = pci_npem_set_led_classdev(npem, nled); + if (ret) { + npem_free(npem); + return ret; + } + } + + dev->npem = npem; + return 0; +} + +void pci_npem_remove(struct pci_dev *dev) +{ + if (dev->npem) + npem_free(dev->npem); +} + +void pci_npem_create(struct pci_dev *dev) +{ + const struct npem_ops *ops = &npem_ops; + int pos = 0, ret; + u32 cap; + + if (!npem_has_dsm(dev)) { + pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_NPEM); + if (pos == 0) + return; + + if (pci_read_config_dword(dev, pos + PCI_NPEM_CAP, &cap) != 0 || + (cap & PCI_NPEM_CAP_CAPABLE) == 0) + return; + } else { + /* + * OS should use the DSM for LED control if it is available + * PCI Firmware Spec r3.3 sec 4.7. + */ + return; + } + + ret = pci_npem_init(dev, ops, pos, cap); + if (ret) + pci_err(dev, "Failed to register PCIe Enclosure Management driver, err: %d\n", + ret); +} diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h index fd44565c4756..9dea8c7353ab 100644 --- a/drivers/pci/pci.h +++ b/drivers/pci/pci.h @@ -333,6 +333,14 @@ static inline void pci_doe_destroy(struct pci_dev *pdev) { } static inline void pci_doe_disconnected(struct pci_dev *pdev) { } #endif +#ifdef CONFIG_PCI_NPEM +void pci_npem_create(struct pci_dev *dev); +void pci_npem_remove(struct pci_dev *dev); +#else +static inline void pci_npem_create(struct pci_dev *dev) { } +static inline void pci_npem_remove(struct pci_dev *dev) { } +#endif + /** * pci_dev_set_io_state - Set the new error state if possible. * diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 8e696e547565..b8ea6353e27a 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -2582,6 +2582,8 @@ void pci_device_add(struct pci_dev *dev, struct pci_bus *bus) dev->match_driver = false; ret = device_add(&dev->dev); WARN_ON(ret < 0); + + pci_npem_create(dev); } struct pci_dev *pci_scan_single_device(struct pci_bus *bus, int devfn) diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index d749ea8250d6..1436f9cf1fea 100644 --- a/drivers/pci/remove.c +++ b/drivers/pci/remove.c @@ -33,6 +33,8 @@ static void pci_destroy_dev(struct pci_dev *dev) if (!dev->dev.kobj.parent) return; + pci_npem_remove(dev); + device_del(&dev->dev); down_write(&pci_bus_sem); diff --git a/include/linux/pci.h b/include/linux/pci.h index fb004fd4e889..c327c2dd4527 100644 --- a/include/linux/pci.h +++ b/include/linux/pci.h @@ -517,6 +517,9 @@ struct pci_dev { #endif #ifdef CONFIG_PCI_DOE struct xarray doe_mbs; /* Data Object Exchange mailboxes */ +#endif +#ifdef CONFIG_PCI_NPEM + struct npem *npem; /* Native PCIe Enclosure Management */ #endif u16 acs_cap; /* ACS Capability offset */ phys_addr_t rom; /* Physical address if not from BAR */ diff --git a/include/uapi/linux/pci_regs.h b/include/uapi/linux/pci_regs.h index 94c00996e633..97e8b7ed9998 100644 --- a/include/uapi/linux/pci_regs.h +++ b/include/uapi/linux/pci_regs.h @@ -740,6 +740,7 @@ #define PCI_EXT_CAP_ID_DVSEC 0x23 /* Designated Vendor-Specific */ #define PCI_EXT_CAP_ID_DLF 0x25 /* Data Link Feature */ #define PCI_EXT_CAP_ID_PL_16GT 0x26 /* Physical Layer 16.0 GT/s */ +#define PCI_EXT_CAP_ID_NPEM 0x29 /* Native PCIe Enclosure Management */ #define PCI_EXT_CAP_ID_PL_32GT 0x2A /* Physical Layer 32.0 GT/s */ #define PCI_EXT_CAP_ID_DOE 0x2E /* Data Object Exchange */ #define PCI_EXT_CAP_ID_MAX PCI_EXT_CAP_ID_DOE @@ -1121,6 +1122,39 @@ #define PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_MASK 0x000000F0 #define PCI_PL_16GT_LE_CTRL_USP_TX_PRESET_SHIFT 4 +/* Native PCIe Enclosure Management */ +#define PCI_NPEM_CAP 0x04 /* NPEM capability register */ +#define PCI_NPEM_CAP_CAPABLE 0x00000001 /* NPEM Capable */ + +#define PCI_NPEM_CTRL 0x08 /* NPEM control register */ +#define PCI_NPEM_CTRL_ENABLE 0x00000001 /* NPEM Enable */ + +#define PCI_NPEM_STATUS 0x0c /* NPEM status register */ +#define PCI_NPEM_STATUS_CC 0x00000001 /* NPEM Command completed */ +/* + * Native PCIe Enclosure Management indication bits and Reset command bit + * are corresponding for capability and control registers. + */ +#define PCI_NPEM_CMD_RESET 0x00000002 /* NPEM Reset Command */ +#define PCI_NPEM_IND_OK 0x00000004 /* NPEM indication OK */ +#define PCI_NPEM_IND_LOCATE 0x00000008 /* NPEM indication Locate */ +#define PCI_NPEM_IND_FAIL 0x00000010 /* NPEM indication Fail */ +#define PCI_NPEM_IND_REBUILD 0x00000020 /* NPEM indication Rebuild */ +#define PCI_NPEM_IND_PFA 0x00000040 /* NPEM indication Predicted Failure Analysis */ +#define PCI_NPEM_IND_HOTSPARE 0x00000080 /* NPEM indication Hot Spare */ +#define PCI_NPEM_IND_ICA 0x00000100 /* NPEM indication In Critical Array */ +#define PCI_NPEM_IND_IFA 0x00000200 /* NPEM indication In Failed Array */ +#define PCI_NPEM_IND_IDT 0x00000400 /* NPEM indication Invalid Device Type */ +#define PCI_NPEM_IND_DISABLED 0x00000800 /* NPEM indication Disabled */ +#define PCI_NPEM_IND_SPEC_0 0x00800000 +#define PCI_NPEM_IND_SPEC_1 0x01000000 +#define PCI_NPEM_IND_SPEC_2 0x02000000 +#define PCI_NPEM_IND_SPEC_3 0x04000000 +#define PCI_NPEM_IND_SPEC_4 0x08000000 +#define PCI_NPEM_IND_SPEC_5 0x10000000 +#define PCI_NPEM_IND_SPEC_6 0x20000000 +#define PCI_NPEM_IND_SPEC_7 0x40000000 + /* Data Object Exchange */ #define PCI_DOE_CAP 0x04 /* DOE Capabilities Register */ #define PCI_DOE_CAP_INT_SUP 0x00000001 /* Interrupt Support */ -- 2.35.3
