Re: [PATCH v3 7/7] arm64: dts: qcom: ipq9574: add PCIe2 nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Apr 18, 2024 at 10:33:23AM -0500, mr.nuke.me@xxxxxxxxx wrote:
> 
> 
> On 4/17/24 02:34, Manivannan Sadhasivam wrote:
> > On Mon, Apr 15, 2024 at 01:20:52PM -0500, Alexandru Gagniuc wrote:
> > > On ipq9574, there are 4 PCIe controllers. Describe the pcie2 node, and
> > > its PHY in devicetree.
> > > 
> > > Only pcie2 is described, because only hardware using that controller
> > > was available for testing.
> > > 
> > 
> > You should describe all the instances in DT. Since the unused ones will be
> > 'disabled', it won't affect anyone.
> 
> My concern with untested but "disabled" descriptions is that someone may
> think it's supported, try to enable it on their board, and run into issues.
> Theoretically, we could describe pcie3, as it uses the same gen3x2 phy.
> 

Okay.

> The pcie0 and pcie1 use a gen3x1 phy, which I do not support in this series.
> I would have to leave the "phys" and "phy-names" for these nodes, leading to
> an incomplete description
> 

Fine then. Please describe at least pcie3. Also add a TODO above the first pcie
node mentioning that someone need to populate others too.

- Mani

> Given this info, do you still wish that I add all other pcie nodes?
> 
> > > Signed-off-by: Alexandru Gagniuc <mr.nuke.me@xxxxxxxxx>
> > > ---
> > >   arch/arm64/boot/dts/qcom/ipq9574.dtsi | 93 ++++++++++++++++++++++++++-
> > >   1 file changed, 92 insertions(+), 1 deletion(-)
> > > 
> > > diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> > > index 7f2e5cbf3bbb..f075e2715300 100644
> > > --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> > > +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> > > @@ -300,7 +300,7 @@ gcc: clock-controller@1800000 {
> > >   				 <0>,
> > >   				 <0>,
> > >   				 <0>,
> > > -				 <0>,
> > > +				 <&pcie2_phy>,
> > >   				 <0>,
> > >   				 <0>;
> > >   			#clock-cells = <1>;
> > > @@ -745,6 +745,97 @@ frame@b128000 {
> > >   				status = "disabled";
> > >   			};
> > >   		};
> > > +
> > > +		pcie2_phy: phy@8c000 {
> > > +			compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> > > +			reg = <0x0008c000 0x14f4>;
> > > +
> > > +			clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> > > +				 <&gcc GCC_PCIE2_AHB_CLK>,
> > > +				 <&gcc GCC_PCIE2_PIPE_CLK>,
> > > +				 <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> > > +				 <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>;
> > > +			clock-names = "aux",
> > > +				      "cfg_ahb",
> > > +				      "pipe",
> > > +				      "anoc",
> > > +				      "snoc";
> > > +
> > > +			clock-output-names = "pcie_phy2_pipe_clk";
> > > +			#clock-cells = <0>;
> > > +			#phy-cells = <0>;
> > > +
> > > +			resets = <&gcc GCC_PCIE2_PHY_BCR>,
> > > +				 <&gcc GCC_PCIE2PHY_PHY_BCR>;
> > > +			reset-names = "phy",
> > > +				      "common";
> > > +			status = "disabled";
> > > +		};
> > > +
> > > +		pcie2: pcie@20000000 {
> > > +			compatible = "qcom,pcie-ipq9574";
> > > +			reg = <0x20000000 0xf1d>,
> > > +			      <0x20000f20 0xa8>,
> > > +			      <0x20001000 0x1000>,
> > > +			      <0x00088000 0x4000>,
> > > +			      <0x20100000 0x1000>;
> > > +			reg-names = "dbi", "elbi", "atu", "parf", "config";
> > > +
> > > +			ranges = <0x81000000 0x0 0x20200000 0x20200000 0x0 0x00100000>,	/* I/O */
> > 
> > Please use below range:
> > 
> > <0x01000000 0x0 0x00000000 0x20200000 0x0 0x00100000>
> > <0x02000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>
> > 
> Of course, thank you.
> 
> > > +				 <0x82000000 0x0 0x20300000 0x20300000 0x0 0x07d00000>;	/* MEM */
> > > +
> > > +			device_type = "pci";
> > > +			linux,pci-domain = <3>;
> > > +			bus-range = <0x00 0xff>;
> > > +			num-lanes = <2>;
> > > +			max-link-speed = <3>;
> > > +			#address-cells = <3>;
> > > +			#size-cells = <2>;
> > > +
> > > +			phys = <&pcie2_phy>;
> > > +			phy-names = "pciephy";
> > > +
> > > +			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
> > > +			interrupt-names = "msi";
> > > +
> > > +			#interrupt-cells = <1>;
> > > +			interrupt-map-mask = <0 0 0 0x7>;
> > > +			interrupt-map = <0 0 0 1 &intc 0 0 164
> > > +					 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> > > +					<0 0 0 2 &intc 0 0 165
> > > +					 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> > > +					<0 0 0 3 &intc 0 0 186
> > > +					 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> > > +					<0 0 0 4 &intc 0 0 187
> > > +					 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> > 
> > Use a single line for each INTX entry even if it exceeds 80 column width.
> 
> Yes. Will do.
> 
> > - Mani
> > 

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux