On Wed, Apr 10, 2024 at 09:48:31AM +0900, Yoshihiro Shimoda wrote:
> This driver previously supported r8a779f0 (R-Car S4-8). Add support
> for r8a779g0 (R-Car V4H).
>
> To support r8a779g0, it requires specific firmware.
>
Add more information about the new SoC. Like features, why firmware is needed,
how it is downloaded/verified etc...
> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@xxxxxxxxxxx>
> ---
> drivers/pci/controller/dwc/pcie-rcar-gen4.c | 201 +++++++++++++++++++-
> 1 file changed, 200 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/pci/controller/dwc/pcie-rcar-gen4.c b/drivers/pci/controller/dwc/pcie-rcar-gen4.c
> index 47ec394885f5..a62804674f4e 100644
> --- a/drivers/pci/controller/dwc/pcie-rcar-gen4.c
> +++ b/drivers/pci/controller/dwc/pcie-rcar-gen4.c
> @@ -5,8 +5,10 @@
> */
>
> #include <linux/delay.h>
> +#include <linux/firmware.h>
> #include <linux/interrupt.h>
> #include <linux/io.h>
> +#include <linux/iopoll.h>
> #include <linux/module.h>
> #include <linux/of.h>
> #include <linux/pci.h>
> @@ -20,9 +22,10 @@
> /* Renesas-specific */
> /* PCIe Mode Setting Register 0 */
> #define PCIEMSR0 0x0000
> -#define BIFUR_MOD_SET_ON BIT(0)
> +#define APP_SRIS_MODE BIT(6)
> #define DEVICE_TYPE_EP 0
> #define DEVICE_TYPE_RC BIT(4)
> +#define BIFUR_MOD_SET_ON BIT(0)
>
> /* PCIe Interrupt Status 0 */
> #define PCIEINTSTS0 0x0084
> @@ -37,19 +40,47 @@
> #define PCIEDMAINTSTSEN 0x0314
> #define PCIEDMAINTSTSEN_INIT GENMASK(15, 0)
>
> +/* Port Logic Registers 89 */
> +#define PRTLGC89 0x0b70
> +
> +/* Port Logic Registers 90 */
> +#define PRTLGC90 0x0b74
> +
> /* PCIe Reset Control Register 1 */
> #define PCIERSTCTRL1 0x0014
> #define APP_HOLD_PHY_RST BIT(16)
> #define APP_LTSSM_ENABLE BIT(0)
>
> +/* PCIe Power Management Control */
> +#define PCIEPWRMNGCTRL 0x0070
> +#define APP_CLK_REQ_N BIT(11)
> +#define APP_CLK_PM_EN BIT(10)
> +
> +/*
> + * The R-Car Gen4 documents don't describe the PHY registers' name.
> + * But, the initialization procedure describes these offsets. So,
> + * this driver makes up own #defines for the offsets.
> + */
This provides no information at all. So better hardcode them.
> +#define RCAR_GEN4_PCIE_PHY_0f8 0x0f8
> +#define RCAR_GEN4_PCIE_PHY_148 0x148
> +#define RCAR_GEN4_PCIE_PHY_1d4 0x1d4
> +#define RCAR_GEN4_PCIE_PHY_514 0x514
> +#define RCAR_GEN4_PCIE_PHY_700 0x700
> +
> #define RCAR_NUM_SPEED_CHANGE_RETRIES 10
> #define RCAR_MAX_LINK_SPEED 4
>
> #define RCAR_GEN4_PCIE_EP_FUNC_DBI_OFFSET 0x1000
> #define RCAR_GEN4_PCIE_EP_FUNC_DBI2_OFFSET 0x800
>
> +#define RCAR_GEN4_PCIE_FIRMWARE_NAME "rcar_gen4_pcie.bin"
> +#define RCAR_GEN4_PCIE_FIRMWARE_BASE_ADDR 0xc000
> +
> +MODULE_FIRMWARE(RCAR_GEN4_PCIE_FIRMWARE_NAME);
> +
> struct rcar_gen4_pcie;
> struct rcar_gen4_pcie_platdata {
> + void (*additional_common_init)(struct rcar_gen4_pcie *rcar);
> int (*ltssm_enable)(struct rcar_gen4_pcie *rcar);
> enum dw_pcie_device_mode mode;
> };
> @@ -57,12 +88,144 @@ struct rcar_gen4_pcie_platdata {
> struct rcar_gen4_pcie {
> struct dw_pcie dw;
> void __iomem *base;
> + void __iomem *phy_base;
> struct platform_device *pdev;
> const struct rcar_gen4_pcie_platdata *platdata;
> };
> #define to_rcar_gen4_pcie(_dw) container_of(_dw, struct rcar_gen4_pcie, dw)
>
> /* Common */
> +static void rcar_gen4_pcie_phy_reg_update_bits(struct rcar_gen4_pcie *rcar,
> + u32 offset, u32 mask, u32 val)
> +{
> + u32 tmp;
> +
> + tmp = readl(rcar->phy_base + offset);
> + tmp &= ~mask;
> + tmp |= val;
> + writel(tmp, rcar->phy_base + offset);
If you use FIELD_* macros, then the values can be passed sensibly ie., just 0
and 1.
> +}
> +
> +static int rcar_gen4_pcie_reg_check_bit(struct rcar_gen4_pcie *rcar,
rcar_gen4_pcie_reg_check()?
> + u32 offset, u32 mask)
> +{
> + struct dw_pcie *dw = &rcar->dw;
> +
> + if (dw_pcie_readl_dbi(dw, offset) & mask)
> + return -EAGAIN;
> +
> + return 0;
> +}
> +
> +static int rcar_gen4_pcie_update_phy_firmware(struct rcar_gen4_pcie *rcar)
> +{
> + const u32 check_addr[] = { 0x00101018, 0x00101118, 0x00101021, 0x00101121};
What are these addresses?
> + struct dw_pcie *dw = &rcar->dw;
> + const struct firmware *fw;
> + unsigned int i, timeout;
> + u32 data;
> + int ret;
> +
> + ret = request_firmware(&fw, RCAR_GEN4_PCIE_FIRMWARE_NAME, dw->dev);
Is this the PHY firmware or PCIe?
> + if (ret) {
> + dev_err(dw->dev, "%s: Requesting firmware failed\n", __func__);
Please, do not print function names in error log.
> + return ret;
> + }
> +
> + for (i = 0; i < (fw->size / 2); i++) {
> + data = fw->data[i * 2] | fw->data[(i * 2) + 1] << 8;
Well, the usual concat order is:
data << 8 | data
> + timeout = 100;
> + do {
> + dw_pcie_writel_dbi(dw, PRTLGC89, RCAR_GEN4_PCIE_FIRMWARE_BASE_ADDR + i);
> + dw_pcie_writel_dbi(dw, PRTLGC90, data);
> + if (rcar_gen4_pcie_reg_check_bit(rcar, PRTLGC89, BIT(30)) >= 0)
What is going on here? Please add a comment to make it clear.
> + break;
> + if (!(--timeout)) {
> + ret = -ETIMEDOUT;
> + goto exit;
> + }
> + usleep_range(100, 200);
> + } while (1);
> + }
> +
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_0f8, BIT(17), BIT(17));
> +
> + for (i = 0; i < ARRAY_SIZE(check_addr); i++) {
> + timeout = 100;
> + do {
> + dw_pcie_writel_dbi(dw, PRTLGC89, check_addr[i]);
> + ret = rcar_gen4_pcie_reg_check_bit(rcar, PRTLGC89, BIT(30));
> + ret |= rcar_gen4_pcie_reg_check_bit(rcar, PRTLGC90, BIT(0));
> + if (ret >= 0)
> + break;
> + if (!(--timeout)) {
> + ret = -ETIMEDOUT;
> + goto exit;
> + }
> + usleep_range(100, 200);
> + } while (1);
> + }
> +
> + ret = 0;
return 0
> +exit:
> + release_firmware(fw);
> +
> + return ret;
> +}
> +
> +static int rcar_gen4_pcie_enable_phy(struct rcar_gen4_pcie *rcar)
> +{
> + struct dw_pcie *dw = &rcar->dw;
> + u32 val;
> + int ret;
> +
> + val = dw_pcie_readl_dbi(dw, PCIE_PORT_FORCE);
> + val |= PORT_FORCE_DO_DESKEW_FOR_SRIS;
> + dw_pcie_writel_dbi(dw, PCIE_PORT_FORCE, val);
> +
> + val = readl(rcar->base + PCIEMSR0);
> + val |= APP_SRIS_MODE;
> + writel(val, rcar->base + PCIEMSR0);
> +
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(28), 0);
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(20), 0);
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(12), 0);
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_700, BIT(4), 0);
> +
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
> + GENMASK(23, 22), BIT(22));
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
> + GENMASK(18, 16), GENMASK(17, 16));
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
> + GENMASK(7, 6), BIT(6));
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_148,
> + GENMASK(2, 0), GENMASK(11, 0));
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_1d4,
> + GENMASK(16, 15), GENMASK(16, 15));
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_514, BIT(26), BIT(26));
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_0f8, BIT(16), 0);
> + rcar_gen4_pcie_phy_reg_update_bits(rcar, RCAR_GEN4_PCIE_PHY_0f8, BIT(19), BIT(19));
> +
> + val = readl(rcar->base + PCIERSTCTRL1);
> + val &= ~APP_HOLD_PHY_RST;
> + writel(val, rcar->base + PCIERSTCTRL1);
> +
> + ret = readl_poll_timeout(rcar->phy_base + RCAR_GEN4_PCIE_PHY_0f8, val,
> + !(val & BIT(18)), 100, 10000);
> + if (ret < 0)
> + return ret;
> +
> + ret = rcar_gen4_pcie_update_phy_firmware(rcar);
Updating or downloading the PHY firmware?
> + if (ret)
> + return ret;
> +
> + val = readl(rcar->base + PCIERSTCTRL1);
> + val |= APP_LTSSM_ENABLE;
> + writel(val, rcar->base + PCIERSTCTRL1);
> +
> + return 0;
> +}
> +
> static void rcar_gen4_pcie_ltssm_control(struct rcar_gen4_pcie *rcar,
> bool enable)
> {
> @@ -200,6 +363,9 @@ static int rcar_gen4_pcie_common_init(struct rcar_gen4_pcie *rcar)
> if (ret)
> goto err_unprepare;
>
> + if (rcar->platdata->additional_common_init)
> + rcar->platdata->additional_common_init(rcar);
> +
> return 0;
>
> err_unprepare:
> @@ -241,6 +407,10 @@ static void rcar_gen4_pcie_unprepare(struct rcar_gen4_pcie *rcar)
>
> static int rcar_gen4_pcie_get_resources(struct rcar_gen4_pcie *rcar)
> {
> + rcar->phy_base = devm_platform_ioremap_resource_byname(rcar->pdev, "phy");
> + if (IS_ERR(rcar->phy_base))
> + return PTR_ERR(rcar->base);
rcar->phy_base?
- Mani
--
மணிவண்ணன் சதாசிவம்
