Re: [PATCH v2 10/10] PCI: qcom: Implement shutdown() callback to properly reset the endpoint devices

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Apr 03, 2024 at 10:03:26PM +0200, Niklas Cassel wrote:
> On Wed, Apr 03, 2024 at 07:02:17PM +0530, Manivannan Sadhasivam wrote:
> > On Tue, Apr 02, 2024 at 01:18:54PM +0200, Niklas Cassel wrote:
> > > On Mon, Apr 01, 2024 at 09:20:36PM +0530, Manivannan Sadhasivam wrote:
> > > > PCIe host controller drivers are supposed to properly reset the endpoint
> > > > devices during host shutdown/reboot. Currently, Qcom driver doesn't do
> > > > anything during host shutdown/reboot, resulting in both PERST# and refclk
> > > > getting disabled at the same time. This prevents the endpoint device
> > > > firmware to properly reset the state machine. Because, if the refclk is
> > > > cutoff immediately along with PERST#, access to device specific registers
> > > > within the endpoint will result in a firmware crash.
> > > > 
> > > > To address this issue, let's call qcom_pcie_host_deinit() inside the
> > > > shutdown callback, that asserts PERST# and then cuts off the refclk with a
> > > > delay of 1ms, thus allowing the endpoint device firmware to properly
> > > > cleanup the state machine.
> > > 
> > > Hm... a QCOM EP device could be attached to any of the PCIe RC drivers that
> > > we have in the kernel, so it seems a bit weird to fix this problem by
> > > patching the QCOM RC driver only.
> > > 
> > > Which DBI call is it that causes this problem during perst assert on EP side?
> > > 
> > > I assume that it is pci-epf-test:deinit() callback that calls
> > > pci_epc_clear_bar(), which calls dw_pcie_ep_clear_bar(), which will both:
> > > -clear local data structures, e.g.
> > > ep->epf_bar[bar] = NULL;
> > > ep->bar_to_atu[bar] = 0;
> > > 
> > > but also call:
> > > __dw_pcie_ep_reset_bar()
> > > dw_pcie_disable_atu()
> > > 
> > > 
> > > Do we perhaps need to redesign the .deinit EPF callback?
> > > 
> > > Considering that we know that .deinit() will only be called on platforms
> > > where there will be a fundamental core reset, I guess we could do something
> > > like introduce a __dw_pcie_ep_clear_bar() which will only clear the local
> > > data structures. (It might not need to do any DBI writes, since the
> > > fundamental core reset should have reset all values.)
> > > 
> > > Or perhaps instead of letting pci_epf_test_epc_deinit() call
> > > pci_epf_test_clear_bar()/__pci_epf_test_clear_bar() directly, perhaps let
> > > pci_epf_test_epc_deinit() call add a .deinit()/.cleanup() defined in the
> > > EPC driver.
> > > 
> > > This EPC .deinit()/.cleanup() callback would then only clear the
> > > local data structures (no DBI writes...).
> > > 
> > > Something like that?
> > > 
> > 
> > It is not just about the EPF test driver. A function driver may need to do many
> > things to properly reset the state machine. Like in the case of MHI driver, it
> > needs to reset channel state, mask interrupts etc... and all requires writing to
> > some registers. So certainly there should be some time before cutting off the
> > refclk.
> 
> I was more thinking that perhaps we should think of .deinit() as in how
> dw_pcie_ep_init() used to be. It was not allowed to have any DBI writes.
> (The DBI writes were all in dw_pcie_ep_init_complete()).
> So perhaps we could define that a EPF .deinit() callback is not allowed
> to have any DBI writes.
> 
> If we take qcom-ep as an example, as soon as you get a PERST assertion
> the qcom-ep driver calls notify_deinit(), then asserts the reset control,
> disables clocks and regulators.
> 
> Since the PCIe core is held in reset, the hardware is in a well defined
> state, no? Sure, the data structures e.g. bar_to_iatu[], etc., might be
> out of sync, but these could be memset():ed no? Since this is a fundamental
> reset, all registers should be reset to their default state (once reset
> is deasserted).
> 

Well, we could prevent the register access during PERST# assert time in the
endpoint, but my worry is that we will end up with 2 version of the cleanup
APIs. Lets take an example of dw_pcie_edma_remove() API which gets called
during deinit and it touches some eDMA registers.

So should we introduce another API which just clears the sw data structure and
not touching the registers? And this may be needed for other generic APIs as
well.

Ideally, if there is a Link Down event before PERST# assert, then this could've
been solved, but that is also not a spec defined behavior.

- Mani

> For a real PCIe card, if you assert + msleep(100) + deassert PERST, surely
> the endpoint is supposed to be in a good/well defined state, regardless if
> he REFCLK was cutoff at the exact time as PERST was asserted or not?
> 
> I would assume that we would want a PCI EPF driver to behave the same way,
> if possible.
> 
> 
> Kind regards,
> Niklas

-- 
மணிவண்ணன் சதாசிவம்




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux