On 3/19/2024 4:41 PM, Manivannan Sadhasivam wrote:
On Fri, Mar 08, 2024 at 11:12:48AM -0600, Bjorn Helgaas wrote:
On Fri, Mar 08, 2024 at 08:38:52AM +0530, Krishna Chaitanya Chundru wrote:
On 3/8/2024 3:25 AM, Bjorn Helgaas wrote:
[+to Rafael, sorry, another runtime PM question, beginning of thread:
https://lore.kernel.org/r/20240305-runtime_pm_enable-v2-1-a849b74091d1@xxxxxxxxxxx]
On Thu, Mar 07, 2024 at 07:28:54AM +0530, Krishna Chaitanya Chundru wrote:
On 3/6/2024 1:27 AM, Bjorn Helgaas wrote:
On Tue, Mar 05, 2024 at 03:19:01PM +0530, Krishna chaitanya chundru wrote:
The Controller driver is the parent device of the PCIe host bridge,
PCI-PCI bridge and PCIe endpoint as shown below.
PCIe controller(Top level parent & parent of host bridge)
|
v
PCIe Host bridge(Parent of PCI-PCI bridge)
|
v
PCI-PCI bridge(Parent of endpoint driver)
|
v
PCIe endpoint driver
Since runtime PM is disabled for host bridge, the state of the child
devices under the host bridge is not taken into account by PM framework
for the top level parent, PCIe controller. So PM framework, allows
the controller driver to enter runtime PM irrespective of the state
of the devices under the host bridge.
IIUC this says that we runtime suspend the controller even though
runtime PM is disabled for the host bridge? I have a hard time
parsing this; can you cite a function that does this or some relevant
documentation about how this part of runtime PM works?
Generally controller should go to runtime suspend when endpoint client
drivers and pci-pci host bridge drivers goes to runtime suspend as the
controller driver is the parent, but we are observing controller driver
goes to runtime suspend even when client drivers and PCI-PCI bridge are
in active state.
It surprises me that a device could be suspended while children are
active. A PCI-PCI bridge must be in D0 for any devices below it to be
active. The controller is a platform device, not a PCI device, but I
am similarly surprised that we would suspend it when children are
active, which makes me think we didn't set the hierarchy up correctly.
It doesn't seem like we should need to enable runtime PM for a parent
to keep it from being suspended when children are active.
Here we are not enabling runtime PM of the controller device, we are
enabling runtime PM for the bridge device which is maintained by the
PCIe framework. The bridge device is the parent of the PCI-PCI
bridge and child of the controller device. As the bridge device's
runtime PM is not enabled the PM framework is ignoring the child's
runtime status.
OK, it's the host bridge, not the controller.
I'm still surprised that the PM framework will runtime suspend a
device when child devices are active.
There is a catch here. Even though the child devices are funtionally active, PM
framework will only consider their runtime_pm state, which is initially set to
'disabled' for all devices. It is upto the device drivers to enable it when
required.
Here is the initial runtime PM status of each device post boot:
Controller device -> disabled initially but enabled by pcie-qcom.c
Host bridge -> disabled initially
PCIe bridge -> disabled initially but conditionally enabled by portdrv.c
PCIe devices -> disabled initially but enabled by respective drivers like WLAN
Now, when the controller device goes to runtime suspend, PM framework will check
the runtime PM state of the child device (host bridge) and will find it to be
disabled. So it will allow the parent (controller device) to go to runtime
suspend. Only if the child device's state was 'active' it will prevent the
parent to get suspended.
But you may wonder if this is ideal? IMO NO. But we cannot blame the PM
framework here. The responsibility is within the device drivers to handle the PM
state based on the usecase. Ideally, the host bridge driver should've handled
runtime PM state during the probe time. Otherwise, PM framework wouldn't know
when would be the best time to suspend the devices.
And further confused about managing the host bridge runtime PM in a
controller driver. Which other callers of pci_alloc_host_bridge() or
devm_pci_alloc_host_bridge() will need similar changes?
This scenario applies to all host bridges. So I think we should enable it inside
pci_host_probe().
- Mani
I will these runtime enable inside the pci_host_probe().
- Krishna Chaitanya.
