On 2/27/2024 6:52 AM, Bjorn Helgaas wrote:
On Fri, Feb 23, 2024 at 10:29:28AM +0800, Ethan Zhao wrote:
On 2/22/2024 7:24 PM, Dan Carpenter wrote:
On Thu, Feb 22, 2024 at 04:02:51AM -0500, Ethan Zhao wrote:
Because surprise removal could happen anytime, e.g. user could request safe
removal to EP(endpoint device) via sysfs and brings its link down to do
surprise removal cocurrently. such aggressive cases would cause ATS
invalidation request issued to non-existence target device, then deadly
loop to retry that request after ITE fault triggered in interrupt context.
this patch aims to optimize the ITE handling by checking the target device
presence state to avoid retrying the timeout request blindly, thus avoid
hard lockup or system hang.
Devices are valid ATS invalidation request target only when they reside
in the iommu->device_rbtree (probed, not released) and present.
"valid invalidation" is awkward wording. Can we instead say:
If you read them together, sounds like tongue twister. but here "ATS
invalidation request target" is one term in PCIe spec.
"ATS invalidation request target" does not appear in the PCIe spec. I
think you're trying to avoid sending ATS Invalidate Requests when you
know they will not be completed.
It is impossible to reliably determine whether a device will be
present and able to complete an Invalidate Request. No matter what
you check to determine that a device is present *now*, it may be
removed before an Invalidate Request reaches it.
If an Invalidate Request to a non-existent device causes a "deadly
loop" (I'm not sure what that means) or a hard lockup or a system
hang, something is wrong with the hardware. There should be a
The hardware might be innocent, here in the qi_submit_sync() &
qi_check_fault() will retry the timeout request forever if the
target device is gone or the target device always takes too much
time to reponse. there is dead loop here.
This patch aims to break the dead loop for case device is not
present anymore.
But for those devices takes too much time to complete. I am
working on other patches, not in this patchset.
Thanks,
Ethan
mechanism to recover from a timeout in that situation.
You can avoid sending Invalidate Requests to devices that have been
removed, and that will reduce the number of timeout cases. But if you
rely on a check like pci_device_is_present() or
pci_dev_is_disconnected(), there is *always* an unavoidable race
between a device removal and the Invalidate Request.
@@ -1273,6 +1273,9 @@ static int qi_check_fault(struct intel_iommu *iommu, int index, int wait_index)
{
u32 fault;
int head, tail;
+ u64 iqe_err, ite_sid;
+ struct device *dev = NULL;
+ struct pci_dev *pdev = NULL;
struct q_inval *qi = iommu->qi;
int shift = qi_shift(iommu);
@@ -1317,6 +1320,13 @@ static int qi_check_fault(struct intel_iommu *iommu, int index, int wait_index)
tail = readl(iommu->reg + DMAR_IQT_REG);
tail = ((tail >> shift) - 1 + QI_LENGTH) % QI_LENGTH;
+ /*
+ * SID field is valid only when the ITE field is Set in FSTS_REG
+ * see Intel VT-d spec r4.1, section 11.4.9.9
+ */
+ iqe_err = dmar_readq(iommu->reg + DMAR_IQER_REG);
+ ite_sid = DMAR_IQER_REG_ITESID(iqe_err);
+
writel(DMA_FSTS_ITE, iommu->reg + DMAR_FSTS_REG);
pr_info("Invalidation Time-out Error (ITE) cleared\n");
@@ -1326,6 +1336,21 @@ static int qi_check_fault(struct intel_iommu *iommu, int index, int wait_index)
head = (head - 2 + QI_LENGTH) % QI_LENGTH;
} while (head != tail);
+ /*
+ * If got ITE, we need to check if the sid of ITE is one of the
+ * current valid ATS invalidation target devices, if no, or the
+ * target device isn't presnet, don't try this request anymore.
+ * 0 value of ite_sid means old VT-d device, no ite_sid value.
+ */
This comment is kind of confusing.
Really confusing ? this is typo there, resnet-> "present"
/*
* If we have an ITE, then we need to check whether the sid of the ITE
* is in the rbtree (meaning it is probed and not released), and that
* the PCI device is present.
*/
My comment is slightly shorter but I think it has the necessary
information.
+ if (ite_sid) {
+ dev = device_rbtree_find(iommu, ite_sid);
+ if (!dev || !dev_is_pci(dev))
+ return -ETIMEDOUT;
-ETIMEDOUT is weird. The callers don't care which error code we return.
Change this to -ENODEV or something
-ETIMEDOUT means prior ATS invalidation request hit timeout fault, and the
caller really cares about the returned value.
+ pdev = to_pci_dev(dev);
+ if (!pci_device_is_present(pdev) &&
+ ite_sid == pci_dev_id(pci_physfn(pdev)))
The && confused me, but then I realized that probably "ite_sid ==
pci_dev_id(pci_physfn(pdev))" is always true. Can we delete that part?
Here is the fault handling, just double confirm nothing else goes wrong --
beyond the assumption.
pdev = to_pci_dev(dev);
if (!pci_device_is_present(pdev))
return -ENODEV;
+ return -ETIMEDOUT;
-ENODEV.
The ATS invalidation request could be sent from userland in later code,
the userland code will care about the returned value, -ENODEV is one aspect
of the fact (target device not present), while -ETIMEDOUT is another
(timeout happened). we couldn't return them both.
+ }
if (qi->desc_status[wait_index] == QI_ABORT)
return -EAGAIN;
}
Sorry, again for nit picking a v13 patch. I'm not a domain expert but
this patchset seems reasonable to me.
Though this is the v13, it is based on new rbtree code, you are welcome.
Thanks,
Ethan
regards,
dan carpenter
