On Tue, Feb 13, 2024 at 08:22:38AM +0530, Ajay Agarwal wrote:
> On Tue, Feb 06, 2024 at 07:53:19PM +0300, Serge Semin wrote:
> > On Tue, Feb 06, 2024 at 10:12:44PM +0530, Ajay Agarwal wrote:
> > > On Mon, Feb 05, 2024 at 12:52:45AM +0300, Serge Semin wrote:
> > > > On Sun, Feb 04, 2024 at 04:54:25PM +0530, Ajay Agarwal wrote:
> > > > > There can be platforms that do not use/have 32-bit DMA addresses
> > > > > but want to enumerate endpoints which support only 32-bit MSI
> > > > > address. The current implementation of 32-bit IOVA allocation can
> > > > > fail for such platforms, eventually leading to the probe failure.
> > > > >
> > > > > If there vendor driver has already setup the MSI address using
> > > > > some mechanism, use the same. This method can be used by the
> > > > > platforms described above to support EPs they wish to.
> > > > >
> > > > > Else, if the memory region is not reserved, try to allocate a
> > > > > 32-bit IOVA. Additionally, if this allocation also fails, attempt
> > > > > a 64-bit allocation for probe to be successful. If the 64-bit MSI
> > > > > address is allocated, then the EPs supporting 32-bit MSI address
> > > > > will not work.
> > > > >
> > > > > Signed-off-by: Ajay Agarwal <ajayagarwal@xxxxxxxxxx>
> > > > > ---
> > > > > Changelog since v2:
> > > > > - If the vendor driver has setup the msi_data, use the same
> > > > >
> > > > > Changelog since v1:
> > > > > - Use reserved memory, if it exists, to setup the MSI data
> > > > > - Fallback to 64-bit IOVA allocation if 32-bit allocation fails
> > > > >
> > > > > .../pci/controller/dwc/pcie-designware-host.c | 26 ++++++++++++++-----
> > > > > 1 file changed, 20 insertions(+), 6 deletions(-)
> > > > >
> > > > > diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> > > > > index d5fc31f8345f..512eb2d6591f 100644
> > > > > --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> > > > > +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> > > > > @@ -374,10 +374,18 @@ static int dw_pcie_msi_host_init(struct dw_pcie_rp *pp)
> > > > > * order not to miss MSI TLPs from those devices the MSI target
> > > > > * address has to be within the lowest 4GB.
> > > > > *
> > > >
> > > > > - * Note until there is a better alternative found the reservation is
> > > > > - * done by allocating from the artificially limited DMA-coherent
> > > > > - * memory.
> > > >
> > > > Why do you keep deleting this statement? The driver still uses the
> > > > DMA-coherent memory as a workaround. Your solution doesn't solve the
> > > > problem completely. This is another workaround. One more time: the
> > > > correct solution would be to allocate a 32-bit address or some range
> > > > within the 4GB PCIe bus memory with no _RAM_ or some other IO behind.
> > > > Your solution relies on the platform firmware/glue-driver doing that,
> > > > which isn't universally applicable. So please don't drop the comment.
> > > >
> > > ACK.
> > >
> > > > > + * Check if the vendor driver has setup the MSI address already. If yes,
> > > > > + * pick up the same.
> > > >
> > > > This is inferred from the code below. So drop it.
> > > >
> > > ACK.
> > >
> > > > > This will be helpful for platforms that do not
> > > > > + * use/have 32-bit DMA addresses but want to use endpoints which support
> > > > > + * only 32-bit MSI address.
> > > >
> > > > Please merge it into the first part of the comment as like: "Permit
> > > > the platforms to override the MSI target address if they have a free
> > > > PCIe-bus memory specifically reserved for that."
> > > >
> > > ACK.
> > >
> > > > > + * Else, if the memory region is not reserved, try to allocate a 32-bit
> > > > > + * IOVA. Additionally, if this allocation also fails, attempt a 64-bit
> > > > > + * allocation. If the 64-bit MSI address is allocated, then the EPs
> > > > > + * supporting 32-bit MSI address will not work.
> > > >
> > > > This is easily inferred from the code below. So drop it.
> > > >
> > > ACK.
> > >
> > > > > */
> > > >
> > > > > + if (pp->msi_data)
> > > >
> > > > Note this is a physical address for which even zero value might be
> > > > valid. In this case it's the address of the PCIe bus space for which
> > > > AFAICS zero isn't reserved for something special.
> > > >
> >
> > > That is a fair point. What do you suggest we do? Shall we define another
> > > op `set_msi_data` (like init/msi_init/start_link) and if it is defined
> > > by the vendor, then call it? Then vendor has to set the pp->msi_data
> > > there? Let me know.
> >
> > You can define a new capability flag here
> > drivers/pci/controller/dwc/pcie-designware.h (see DW_PCIE_CAP_* macros)
> > , set it in the glue driver by means of the dw_pcie_cap_set() macro
> > function and instead of checking msi_data value test the flag for
> > being set by dw_pcie_cap_is().
> >
> Sure, good suggestion. ACK.
>
> > >
> > > > > + return 0;
> > > > > +
> > > > > ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
> > > > > if (ret)
> > > > > dev_warn(dev, "Failed to set DMA mask to 32-bit. Devices with only 32-bit MSI support may not work properly\n");
> > > > > @@ -385,9 +393,15 @@ static int dw_pcie_msi_host_init(struct dw_pcie_rp *pp)
> > > > > msi_vaddr = dmam_alloc_coherent(dev, sizeof(u64), &pp->msi_data,
> > > > > GFP_KERNEL);
> > > > > if (!msi_vaddr) {
> > > > > - dev_err(dev, "Failed to alloc and map MSI data\n");
> > > > > - dw_pcie_free_msi(pp);
> > > > > - return -ENOMEM;
> > > > > + dev_warn(dev, "Failed to alloc 32-bit MSI data. Attempting 64-bit now\n");
> > > > > + dma_set_coherent_mask(dev, DMA_BIT_MASK(64));
> > > > > + msi_vaddr = dmam_alloc_coherent(dev, sizeof(u64), &pp->msi_data,
> > > > > + GFP_KERNEL);
> > > > > + if (!msi_vaddr) {
> > > > > + dev_err(dev, "Failed to alloc and map MSI data\n");
> > > > > + dw_pcie_free_msi(pp);
> > > > > + return -ENOMEM;
> > > > > + }
> > > >
> > > > On Tue, Jan 30, 2024 at 08:40:48PM +0000, Robin Murphy wrote:
> > > > > Yeah, something like that. Personally I'd still be tempted to try some
> > > > > mildly more involved logic to just have a single dev_warn(), but I think
> > > > > that's less important than just having something which clearly works.
> > > >
> > > > I guess this can be done but in a bit clumsy way. Like this:
> > > >
> > > > ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32)) ||
> > > > !dmam_alloc_coherent(dev, sizeof(u64), &pp->msi_data, GFP_KERNEL);
> > > > if (ret) {
> > > > dev_warn(dev, "Failed to allocate 32-bit MSI target address\n");
> > > >
> > > > dma_set_coherent_mask(dev, DMA_BIT_MASK(64));
> > > > ret = !dmam_alloc_coherent(dev, sizeof(u64), &pp->msi_data, GFP_KERNEL);
> > > > if (ret) {
> > > > dev_err(dev, "Failed to allocate MSI target address\n");
> > > > return -ENOMEM;
> > >
> > > As you pointed out already, this looks pretty clumsy. I think we should
> > > stick to the more descriptive and readable code that I suggested.
> >
> > I do not know which solution is better really. Both have pros and
> > cons. Let's wait for Bjorn, Mani or Robin opinion about this.
> >
> > -Serge(y)
> >
> Bjorn/Mani/Robin,
> Can you please provide your comment?
>
Sergey's suggestion masks out the error coming from "dma_set_coherent_mask()" by
using the same error log. This is equivalent to printing the same error log for
both API failures:
ret = dma_set_coherent_mask()
if (ret)
dev_warn(dev, "Failed to allocate 32-bit MSI target address\n");
ret = dmam_alloc_coherent()
if (ret)
dev_warn(dev, "Failed to allocate 32-bit MSI target address\n");
Which doesn't look correct to me. So let's stick to what Ajay had initially.
- Mani
--
மணிவண்ணன் சதாசிவம்
