On 22-08-23, 10:23, Pavan Kondeti wrote:
> +linux-pm and OPP maintainers
>
> On Tue, Aug 22, 2023 at 09:57:41AM +0530, Krishna Chaitanya Chundru wrote:
> >
> > On 8/22/2023 9:33 AM, Pavan Kondeti wrote:
> > > On Mon, Aug 21, 2023 at 07:45:43PM +0530, Krishna chaitanya chundru wrote:
> > > > Before link training vote for the maximum performance state of RPMH
> > > > and once link is up, vote for the performance state based upon the link
> > > > speed.
> > > >
> > > > Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> > > > ---
> > > > drivers/pci/controller/dwc/pcie-qcom.c | 47 ++++++++++++++++++++++++++++++++++
> > > > 1 file changed, 47 insertions(+)
> > > >
> > > > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> > > > index 7a87a47..c57ca1a 100644
> > > > --- a/drivers/pci/controller/dwc/pcie-qcom.c
> > > > +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> > > > @@ -22,6 +22,7 @@
> > > > #include <linux/of_device.h>
> > > > #include <linux/of_gpio.h>
> > > > #include <linux/pci.h>
> > > > +#include <linux/pm_opp.h>
> > > > #include <linux/pm_runtime.h>
> > > > #include <linux/platform_device.h>
> > > > #include <linux/phy/pcie.h>
> > > > @@ -1357,6 +1358,32 @@ static int qcom_pcie_icc_init(struct qcom_pcie *pcie)
> > > > return 0;
> > > > }
> > > > +static void qcom_pcie_opp_update(struct qcom_pcie *pcie)
> > > > +{
> > > > + struct dw_pcie *pci = pcie->pci;
> > > > + struct dev_pm_opp *opp;
> > > > + u32 offset, status;
> > > > + int speed, ret = 0;
> > > > +
> > > > + offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> > > > + status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
> > > > +
> > > > + /* Only update constraints if link is up. */
> > > > + if (!(status & PCI_EXP_LNKSTA_DLLLA))
> > > > + return;
> > > > +
> > > What happens if link is not up during probe? We set max vote before
> > > this, should not we bring it down in suspend and vote it back again in
> > > resume?
> >
> > ok, I will set to lower value in the suspend path if the link is not up. If
> > the link is already up driver will not
> >
> > do any modifications.
> >
> > >
> > > > + speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
> > > > +
> > > > + opp = dev_pm_opp_find_level_exact(pci->dev, speed);
> > > > + if (!IS_ERR(opp)) {
> > > > + ret = dev_pm_opp_set_opp(pci->dev, opp);
> > > > + if (ret)
> > > > + dev_err(pci->dev, "Failed to set opp: %d\n", ret);
> > > > + dev_pm_opp_put(opp);
> > > > + }
> > > Since you added an error message, make it more useful by printing the
> > > opp level also. dev_pm_opp_get_level().
> > Sure I will add this in next patch.
> > >
> > > > +
> > > > +}
> > > > +
> > > > static void qcom_pcie_icc_update(struct qcom_pcie *pcie)
> > > > {
> > > > struct dw_pcie *pci = pcie->pci;
> > > > @@ -1439,8 +1466,10 @@ static void qcom_pcie_init_debugfs(struct qcom_pcie *pcie)
> > > > static int qcom_pcie_probe(struct platform_device *pdev)
> > > > {
> > > > const struct qcom_pcie_cfg *pcie_cfg;
> > > > + unsigned long max_freq = INT_MAX;
> > > > struct device *dev = &pdev->dev;
> > > > struct qcom_pcie *pcie;
> > > > + struct dev_pm_opp *opp;
> > > > struct dw_pcie_rp *pp;
> > > > struct resource *res;
> > > > struct dw_pcie *pci;
> > > > @@ -1511,6 +1540,22 @@ static int qcom_pcie_probe(struct platform_device *pdev)
> > > > if (ret)
> > > > goto err_pm_runtime_put;
> > > > + /* OPP table is optional */
> > > > + ret = devm_pm_opp_of_add_table(dev);
> > > > + if (ret && ret != -ENODEV) {
> > > > + dev_err(dev, "Invalid OPP table in Device tree\n");
> > > > + goto err_pm_runtime_put;
> > > > + }
> > > > +
> > > > + /* vote for max level in the opp table */
> > > > + opp = dev_pm_opp_find_freq_floor(dev, &max_freq);
> > > > + if (!IS_ERR(opp)) {
> > > > + ret = dev_pm_opp_set_opp(dev, opp);
> > > > + if (ret)
> > > > + dev_err(pci->dev, "Failed to set opp: %d\n", ret);
> > > > + dev_pm_opp_put(opp);
> > > > + }
> > > > +
> > > This needs an update since you moved from frequency based voting to link
> > > speed based voting.
> >
> > dev_pm_opp_find_freq_floor will give us the max the opp level opp we don't
> > have a similar API to get max opp-level
> >
> > For that reason we are using this API.
> >
>
> Ok, thanks. I get that it is working. Would you be not knowing the exact
> level for the max speed supported? if that is unknown, I believe we have
> a use case for dev_pm_opp_find_level_floor() API. Adding the best people
> on this matter for thei valuable opinion/suggestions.
If required feel free to add dev_pm_opp_find_level_floor(), based on
dev_pm_opp_find_level_ceil().
--
viresh
