On 05/07/2023 10:17, Mrinmay Sarkar wrote:
> Add pcie dtsi nodes for two controllers found on sa8775p platform.
>
> Signed-off-by: Mrinmay Sarkar <quic_msarkar@xxxxxxxxxxx>
> ---
> arch/arm64/boot/dts/qcom/sa8775p.dtsi | 201 +++++++++++++++++++++++++-
> 1 file changed, 199 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> index b130136acffe..88749cbaea8b 100644
> --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
> @@ -481,8 +481,8 @@ gcc: clock-controller@100000 {
> <0>,
> <0>,
> <0>,
> - <0>,
> - <0>,
> + <&pcie0_phy>,
> + <&pcie1_phy>,
> <0>,
> <0>,
> <0>;
> @@ -2315,4 +2315,201 @@ arch_timer: timer {
> <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> };
> +
> + pcie0: pci@1c00000{
> + device_type = "pci";
> + compatible = "qcom,pcie-sa8775p";
> + reg = <0x0 0x01c00000 0x0 0x3000>,
> + <0x0 0x40000000 0x0 0xf20>,
> + <0x0 0x40000f20 0x0 0xa8>,
> + <0x0 0x40001000 0x0 0x4000>,
> + <0x0 0x40100000 0x0 0x100000>,
> + <0x0 0x01c03000 0x0 0x1000>;
> + reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
> + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
> + bus-range = <0x00 0xff>;
> +
> + linux,pci-domain = <0>;
> + num-lanes = <2>;
> +
> + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc GIC_SPI 434 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc GIC_SPI 439 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> + <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>;
> +
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_anoc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "pcie-mem";
> +
> + resets = <&gcc GCC_PCIE_0_BCR>;
> + reset-names = "pci";
> + power-domains = <&gcc PCIE_0_GDSC>;
> +
> + phys = <&pcie0_phy>;
> + phy-names = "pciephy";
> +
> + iommus = <&pcie_smmu 0x0000 0x1>;
> + iommu-map = <0x0 &pcie_smmu 0x0000 0x1>,
> + <0x100 &pcie_smmu 0x0001 0x1>;
> +
> + perst-gpios = <&tlmm 2 1>;
> + wake-gpios = <&tlmm 0 0>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie0_default_state>;
> +
> + status = "disabled";
> + };
> +
> + pcie0_phy: phy@1c04000 {
> + compatible = "qcom,sa8775p-qmp-gen4x2-pcie-phy";
> + reg = <0x0 0x1c04000 0x0 0x2000>;
> +
> + clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
> + <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_CLKREF_EN>,
> + <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_0_PHY_AUX_CLK>,
> + <&gcc GCC_PCIE_0_PIPE_CLK>,
> + <&gcc GCC_PCIE_0_PIPEDIV2_CLK>;
> +
> + clock-names = "aux", "cfg_ahb", "ref", "rchng", "phy_aux",
> + "pipe", "pipediv2";
> +
> + assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + power-domains = <&gcc PCIE_0_GDSC>;
> +
> + resets = <&gcc GCC_PCIE_0_PHY_BCR>;
> + reset-names = "phy";
> +
> + #clock-cells = <0>;
> + clock-output-names = "pcie_0_pipe_clk";
> +
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + pcie1: pci@1c10000{
> + device_type = "pci";
compatible is always first property, then reg, then reg-names, then
ranges. Always.
> + compatible = "qcom,pcie-sa8775p";
> + reg = <0x0 0x01c10000 0x0 0x3000>,
> + <0x0 0x60000000 0x0 0xf20>,
> + <0x0 0x60000f20 0x0 0xa8>,
> + <0x0 0x60001000 0x0 0x4000>,
> + <0x0 0x60100000 0x0 0x100000>,
> + <0x0 0x01c13000 0x0 0x1000>;
> + reg-names = "parf", "dbi", "elbi", "atu", "config", "mhi";
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> + ranges = <0x01000000 0x0 0x60200000 0x0 0x60200000 0x0 0x100000>,
> + <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x1fd00000>;
> + bus-range = <0x00 0xff>;
> +
> + linux,pci-domain = <1>;
> + num-lanes = <4>;
> +
> + interrupts = <GIC_SPI 519 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "msi";
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
> + <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
> + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>;
> +
> + clock-names = "aux",
> + "cfg",
> + "bus_master",
> + "bus_slave",
> + "slave_q2a";
> +
> + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
> + assigned-clock-rates = <19200000>;
> +
> + interconnects = <&pcie_anoc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "pcie-mem";
> +
> + resets = <&gcc GCC_PCIE_1_BCR>;
> + reset-names = "pci";
> + power-domains = <&gcc PCIE_1_GDSC>;
> +
> + phys = <&pcie1_phy>;
> + phy-names = "pciephy";
> +
> + iommus = <&pcie_smmu 0x0080 0x1>;
> + iommu-map = <0x0 &pcie_smmu 0x0080 0x1>,
> + <0x100 &pcie_smmu 0x0081 0x1>;
> +
> + perst-gpios = <&tlmm 4 1>;
> + wake-gpios = <&tlmm 5 0>;
Use proper defines.
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie1_default_state>;
> +
> + status = "disabled";
> + };
> +
> + pcie1_phy: phy@1c14000 {
> + compatible = "qcom,sa8775p-qmp-gen4x4-pcie-phy";
> + reg = <0x0 0x1c14000 0x0 0x4000>;
> +
> + clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
> + <&gcc GCC_PCIE_CLKREF_EN>,
> + <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
> + <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
> + <&gcc GCC_PCIE_1_PIPE_CLK>,
> + <&gcc GCC_PCIE_1_PIPEDIV2_CLK>;
> +
> + clock-names = "aux", "cfg_ahb", "ref", "rchng", "phy_aux",
> + "pipe", "pipediv2";
> +
> + assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
> + assigned-clock-rates = <100000000>;
> +
> + power-domains = <&gcc PCIE_1_GDSC>;
> +
> + resets = <&gcc GCC_PCIE_1_PHY_BCR>;
> + reset-names = "phy";
> +
> + #clock-cells = <0>;
> + clock-output-names = "pcie_1_pipe_clk";
> +
> + #phy-cells = <0>;
> +
> + status = "disabled";
> +
No stray blank lines.
> + };
> };
Best regards,
Krzysztof
