Ask for a regression issue of vfio-pci driver with Intel DG2 (A770) discrete graphics card from Linux 6.1

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

Since Linux 6.2 kernel (same happens in Linux 6.4.1), loading vfio-pci driver to a specific HW (Intel DG2 A770) target does not work properly.
(It works fine on Linux 6.1 kernel with the same HW).

The configuration and hardware information used is described in [1].

Starting with the Linux 6.2 kernel, the following log is output to dmesg when a problem occurs.
...
[ 15.049948] pcieport 0000:00:01.0: Data Link Layer Link Active not set in 1000 msec [ 15.050024] pcieport 0000:01:00.0: Unable to change power state from D3cold to D0, device inaccessible [ 15.051067] pcieport 0000:02:01.0: Unable to change power state from D3cold to D0, device inaccessible [ 15.052141] pcieport 0000:02:04.0: Unable to change power state from D3cold to D0, device inaccessible
[ 17.286554] vfio-pci 0000:03:00.0: not ready 1023ms after resume; giving up
[ 17.286553] vfio-pci 0000:04:00.0: not ready 1023ms after resume; giving up
[ 17.286576] vfio-pci 0000:03:00.0: Unable to change power state from D3cold to D0, device inaccessible [ 17.286578] vfio-pci 0000:04:00.0: Unable to change power state from D3cold to D0, device inaccessible
...

And if you check the DG2 hardware using the "lspci -nnv" command, you will see that "Flags:" is displayed as "!!! Unknown header type 7f" as shown below. [2]
The normal output log looks like [3].

This issue has been occurring since the patch below was applied. [4]

d8d2b65a940bb497749d66bdab59b530901d3854 is the first bad commit
commit d8d2b65a940bb497749d66bdab59b530901d3854
Author: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Date:   Fri Dec 9 11:01:00 2022 -0600

    PCI/portdrv: Allow AER service only for Root Ports & RCECs


Rolling back the [4] patch makes it work on boot with the latest version of the kernel, but the same problem still occurs after "suspend to s2idle".
This problem existed even before applying [4].

Suspend has been tested with the following command.
$ systemctl suspend -i

$ cat /sys/power/mem_sleep
[s2idle] deep


Here is the log that is issued when testing suspend to s2idle. [5]


Br,

G.G.


[1] Env:

NUC: intel-nuc-13-extreme-kit-nuc13rngi7 (https://ark.intel.com/content/www/us/en/ark/products/229784/intel-nuc-13-extreme-kit-nuc13rngi7.html)
(MB: Z690, CPU: RPL-S i13700k)

PCIE Card: Intel A770 GPU

Add boot parameter: intel_iommu=on iommu=pt

$ lspci -nn |grep DG2
03:00.0 VGA compatible controller [0300]: Intel Corporation DG2 [Arc A770] [8086:56a0] (rev 08) 04:00.0 Audio device [0403]: Intel Corporation DG2 Audio Controller [8086:4f90]


$ cat /etc/modprobe.d/vfio.conf

options vfio-pci ids=8086:56a0,8086:4f90
softdep drm pre: vfio-pci

[2]
03:00.0 VGA compatible controller [0300]: Intel Corporation DG2 [Arc A770] [8086:56a0] (rev 08) (prog-if 00 [VGA controller])
	Subsystem: Intel Corporation Device [8086:1020]
	!!! Unknown header type 7f
	Memory at 93000000 (64-bit, non-prefetchable) [size=16M]
	Memory at 6000000000 (64-bit, prefetchable) [size=16G]
	Expansion ROM at 94000000 [disabled] [size=2M]
	Kernel driver in use: vfio-pci
	Kernel modules: i915

04:00.0 Audio device [0403]: Intel Corporation DG2 Audio Controller [8086:4f90]
	Subsystem: Intel Corporation Device [8086:1020]
	!!! Unknown header type 7f
	Memory at 94300000 (64-bit, non-prefetchable) [size=16K]
	Kernel driver in use: vfio-pci
	Kernel modules: snd_hda_intel


[3]
03:00.0 VGA compatible controller [0300]: Intel Corporation DG2 [Arc A770] [8086:56a0] (rev 08) (prog-if 00 [VGA controller])
	Subsystem: Intel Corporation Device [8086:1020]
	Flags: bus master, fast devsel, latency 0, IOMMU group 19
	Memory at 93000000 (64-bit, non-prefetchable) [size=16M]
	Memory at 6000000000 (64-bit, prefetchable) [size=16G]
	Expansion ROM at 94000000 [disabled] [size=2M]
	Capabilities: <access denied>
	Kernel driver in use: vfio-pci
	Kernel modules: i915

04:00.0 Audio device [0403]: Intel Corporation DG2 Audio Controller [8086:4f90]
	Subsystem: Intel Corporation Device [8086:1020]
	Flags: fast devsel, IOMMU group 20
	Memory at 94300000 (64-bit, non-prefetchable) [disabled] [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: vfio-pci
	Kernel modules: snd_hda_intel


[4]
commit d8d2b65a940bb497749d66bdab59b530901d3854
Author: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Date:   Fri Dec 9 11:01:00 2022 -0600

    PCI/portdrv: Allow AER service only for Root Ports & RCECs

    Previously portdrv allowed the AER service for any device with an AER
capability (assuming Linux had control of AER) even though the AER service
    driver only attaches to Root Port and RCECs.

    Because get_port_device_capability() included AER for non-RP, non-RCEC
    devices, we tried to initialize the AER IRQ even though these devices
    don't generate AER interrupts.

    Intel DG1 and DG2 discrete graphics cards contain a switch leading to a
    GPU.  The switch supports AER but not MSI, so initializing an AER IRQ
failed, and portdrv failed to claim the switch port at all. The GPU itself could be suspended, but the switch could not be put in a low-power state
    because it had no driver.

    Don't allow the AER service on non-Root Port, non-Root Complex Event
Collector devices. This means we won't enable Bus Mastering if the device doesn't require MSI, the AER service will not appear in sysfs, and the AER
    service driver will not bind to the device.

Link: https://lore.kernel.org/r/20221207084105.84947-1-mika.westerberg@xxxxxxxxxxxxxxx Link: https://lore.kernel.org/r/20221210002922.1749403-1-helgaas@xxxxxxxxxx
    Based-on-patch-by: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
    Signed-off-by: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@xxxxxxxxxxxxxxx>

diff --git a/drivers/pci/pcie/portdrv.c b/drivers/pci/pcie/portdrv.c
index a6c4225505d5..8b16e96ec15c 100644
--- a/drivers/pci/pcie/portdrv.c
+++ b/drivers/pci/pcie/portdrv.c
@@ -232,7 +232,9 @@ static int get_port_device_capability(struct pci_dev *dev)
        }

 #ifdef CONFIG_PCIEAER
-       if (dev->aer_cap && pci_aer_available() &&
+       if ((pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
+             pci_pcie_type(dev) == PCI_EXP_TYPE_RC_EC) &&
+           dev->aer_cap && pci_aer_available() &&
            (pcie_ports_native || host->native_aer))
                services |= PCIE_PORT_SERVICE_AER;
 #endif


[5]
[   71.995824] PM: suspend entry (s2idle)
[   72.000793] Filesystems sync: 0.004 seconds
[   72.153926] Freezing user space processes
[ 72.156234] Freezing user space processes completed (elapsed 0.002 seconds)
[   72.156244] OOM killer disabled.
[   72.156246] Freezing remaining freezable tasks
[ 72.157616] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) [ 72.157619] printk: Suspending console(s) (use no_console_suspend to debug)
[   73.756457] ACPI: EC: interrupt blocked
[ 75.103988] ucsi_acpi USBC000:00: ucsi_handle_connector_change: GET_CONNECTOR_STATUS failed (-5)
[   84.052478] ACPI: EC: interrupt unblocked
[ 86.085388] pcieport 0000:00:01.0: Data Link Layer Link Active not set in 1000 msec [ 86.085523] pcieport 0000:01:00.0: Unable to change power state from D3cold to D0, device inaccessible [ 86.086984] pci 0000:02:01.0: Unable to change power state from D3cold to D0, device inaccessible [ 86.087005] pci 0000:02:04.0: Unable to change power state from D3cold to D0, device inaccessible
[   88.335403] vfio-pci 0000:04:00.0: not ready 1023ms after resume; waiting
[   88.335427] vfio-pci 0000:03:00.0: not ready 1023ms after resume; waiting
[   89.375444] vfio-pci 0000:04:00.0: not ready 2047ms after resume; waiting
[   89.375471] vfio-pci 0000:03:00.0: not ready 2047ms after resume; waiting
[   91.615418] vfio-pci 0000:04:00.0: not ready 4095ms after resume; waiting
[   91.615439] vfio-pci 0000:03:00.0: not ready 4095ms after resume; waiting
[   95.882059] vfio-pci 0000:04:00.0: not ready 8191ms after resume; waiting
[   95.882081] vfio-pci 0000:03:00.0: not ready 8191ms after resume; waiting
[ 104.202062] vfio-pci 0000:04:00.0: not ready 16383ms after resume; waiting [ 104.202066] vfio-pci 0000:03:00.0: not ready 16383ms after resume; waiting [ 121.482058] vfio-pci 0000:04:00.0: not ready 32767ms after resume; waiting [ 121.482067] vfio-pci 0000:03:00.0: not ready 32767ms after resume; waiting [ 155.615409] vfio-pci 0000:04:00.0: not ready 65535ms after resume; giving up [ 155.615412] vfio-pci 0000:03:00.0: not ready 65535ms after resume; giving up [ 155.633757] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/tgl_guc_70.bin version 70.5.1 [ 155.633761] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3
[  155.636177] i915 0000:00:02.0: [drm] GT0: HuC: authenticated!
[  155.636860] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled
[  155.636860] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled
[  155.637228] i915 0000:00:02.0: [drm] GT0: GUC: RC enabled
[  155.661583] nvme nvme0: Shutdown timeout set to 10 seconds
[  155.663188] nvme nvme0: 24/0/0 default/read/poll queues
[  155.674267] iwlwifi 0000:00:14.3: WRT: Invalid buffer destination
[  155.823379] ucsi_acpi USBC000:00: possible UCSI driver bug 1
[  155.823390] ucsi_acpi USBC000:00: failed to re-enable notifications (-22)
[  155.833326] iwlwifi 0000:00:14.3: WFPM_UMAC_PD_NOTIFICATION: 0x1f
[  155.833358] iwlwifi 0000:00:14.3: WFPM_LMAC2_PD_NOTIFICATION: 0x0
[  155.833367] iwlwifi 0000:00:14.3: WFPM_AUTH_KEY_0: 0x90
[  155.833377] iwlwifi 0000:00:14.3: CNVI_SCU_SEQ_DATA_DW9: 0x960
[  155.942363] ata6: SATA link down (SStatus 4 SControl 300)
[  155.942537] ata5: SATA link down (SStatus 4 SControl 300)
[ 156.030241] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
[  156.030830] OOM killer enabled.
[  156.030831] Restarting tasks ...
[ 156.030894] mei_pxp 0000:00:16.0-fbf6fcf1-96cf-4e2e-a6a6-1bab8cbe36b1: bound 0000:00:02.0 (ops i915_pxp_tee_component_ops [i915])
[  156.031827] done.
[  156.031837] random: crng reseeded on system resumption
[  156.036058] PM: suspend exit
[  158.962881] wlp0s20f3: authenticate with 4c:ed:fb:a0:7f:6c
[  158.966647] wlp0s20f3: send auth to 4c:ed:fb:a0:7f:6c (try 1/3)
[  159.001337] wlp0s20f3: authenticated
[  159.001858] wlp0s20f3: associate with 4c:ed:fb:a0:7f:6c (try 1/3)
[ 159.002882] wlp0s20f3: RX AssocResp from 4c:ed:fb:a0:7f:6c (capab=0x11 status=0 aid=1)
[  159.010807] wlp0s20f3: associated
[  159.159528] IPv6: ADDRCONF(NETDEV_CHANGE): wlp0s20f3: link becomes ready
[ 287.875205] vfio-pci 0000:04:00.0: Unable to change power state from D3cold to D0, device inaccessible [ 287.936500] vfio-pci 0000:04:00.0: Unable to change power state from D3cold to D0, device inaccessible [ 289.414087] vfio-pci 0000:03:00.0: Unable to change power state from D3cold to D0, device inaccessible [ 289.475297] vfio-pci 0000:03:00.0: Unable to change power state from D3cold to D0, device inaccessible



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux