Re: [PATCH v3 3/3] PCI: qcom-ep: Add ICC bandwidth voting support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 9 Jun 2023 at 14:47, Krishna chaitanya chundru
<quic_krichai@xxxxxxxxxxx> wrote:
>
> Add support to vote for ICC bandwidth based on the link speed and width.
>
> This patch is inspired from pcie-qcom driver to add basic interconnect
> support.
>
> Link: https://lore.kernel.org/all/20221102090705.23634-1-johan+linaro@xxxxxxxxxx/

This link should be a part of the cover letter, not the commit msg. If
you want to refer to the previous commits, please use the standard
reference: commit abcdefabc ("PCI: qcom: Make foo and bar").

> Signed-off-by: Krishna chaitanya chundru <quic_krichai@xxxxxxxxxxx>
> ---
>  drivers/pci/controller/dwc/pcie-qcom-ep.c | 68 +++++++++++++++++++++++++++++++
>  1 file changed, 68 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom-ep.c b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> index 19b3283..baf831f 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom-ep.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom-ep.c
> @@ -13,6 +13,7 @@
>  #include <linux/debugfs.h>
>  #include <linux/delay.h>
>  #include <linux/gpio/consumer.h>
> +#include <linux/interconnect.h>
>  #include <linux/mfd/syscon.h>
>  #include <linux/phy/pcie.h>
>  #include <linux/phy/phy.h>
> @@ -28,6 +29,7 @@
>  #define PARF_SYS_CTRL                          0x00
>  #define PARF_DB_CTRL                           0x10
>  #define PARF_PM_CTRL                           0x20
> +#define PARF_PM_STTS                           0x24
>  #define PARF_MHI_CLOCK_RESET_CTRL              0x174
>  #define PARF_MHI_BASE_ADDR_LOWER               0x178
>  #define PARF_MHI_BASE_ADDR_UPPER               0x17c
> @@ -128,6 +130,9 @@
>  /* DBI register fields */
>  #define DBI_CON_STATUS_POWER_STATE_MASK                GENMASK(1, 0)
>
> +#define DBI_LINKCTRLSTATUS                     0x80
> +#define DBI_LINKCTRLSTATUS_SHIFT               16
> +
>  #define XMLH_LINK_UP                           0x400
>  #define CORE_RESET_TIME_US_MIN                 1000
>  #define CORE_RESET_TIME_US_MAX                 1005
> @@ -178,6 +183,8 @@ struct qcom_pcie_ep {
>         struct phy *phy;
>         struct dentry *debugfs;
>
> +       struct icc_path *icc_mem;
> +
>         struct clk_bulk_data *clks;
>         int num_clks;
>
> @@ -253,9 +260,51 @@ static void qcom_pcie_dw_stop_link(struct dw_pcie *pci)
>         disable_irq(pcie_ep->perst_irq);
>  }
>
> +static void qcom_pcie_ep_icc_update(struct qcom_pcie_ep *pcie_ep)
> +{
> +       struct dw_pcie *pci = &pcie_ep->pci;
> +       u32 offset, status, bw;
> +       int speed, width;
> +       int ret;
> +
> +       if (!pcie_ep->icc_mem)
> +               return;
> +
> +       offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> +       status = readw(pci->dbi_base + offset + PCI_EXP_LNKSTA);
> +
> +       speed = FIELD_GET(PCI_EXP_LNKSTA_CLS, status);
> +       width = FIELD_GET(PCI_EXP_LNKSTA_NLW, status);
> +
> +       switch (speed) {
> +       case 1:
> +               bw = MBps_to_icc(250);  /* BW for GEN1 per lane: 250MBps */

Please extract these constants to the defines. This would save you
from duplicating 250 below.

> +               break;
> +       case 2:
> +               bw = MBps_to_icc(500);  /* BW for GEN2 per lane: 500MBps */
> +               break;
> +       case 3:
> +               bw = MBps_to_icc(985);  /* BW for GEN3 per lane: 985MBps */
> +               break;
> +       default:
> +               WARN_ON_ONCE(1);
> +               fallthrough;
> +       case 4:
> +               bw = MBps_to_icc(1969); /* BW for GEN4 per lane:1969MBps */
> +               break;
> +       }
> +
> +       ret = icc_set_bw(pcie_ep->icc_mem, 0, width * bw);
> +       if (ret) {
> +               dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> +                       ret);
> +       }
> +}
> +
>  static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
>  {
>         int ret;
> +       struct dw_pcie *pci = &pcie_ep->pci;
>
>         ret = clk_bulk_prepare_enable(pcie_ep->num_clks, pcie_ep->clks);
>         if (ret)
> @@ -277,6 +326,20 @@ static int qcom_pcie_enable_resources(struct qcom_pcie_ep *pcie_ep)
>         if (ret)
>                 goto err_phy_exit;
>
> +       /*
> +        * Some Qualcomm platforms require interconnect bandwidth constraints
> +        * to be set before enabling interconnect clocks.
> +        *
> +        * Set an initial average bandwidth corresponding to GEN1x1(250 MBps)
> +        * for the pcie to mem path.
> +        */
> +       ret = icc_set_bw(pcie_ep->icc_mem, 0, MBps_to_icc(250));
> +       if (ret) {
> +               dev_err(pci->dev, "failed to set interconnect bandwidth: %d\n",
> +                       ret);
> +               goto err_phy_exit;
> +       }
> +
>         return 0;
>
>  err_phy_exit:
> @@ -550,6 +613,10 @@ static int qcom_pcie_ep_get_resources(struct platform_device *pdev,
>         if (IS_ERR(pcie_ep->phy))
>                 ret = PTR_ERR(pcie_ep->phy);
>
> +       pcie_ep->icc_mem = devm_of_icc_get(dev, "pcie-mem");
> +       if (IS_ERR(pcie_ep->icc_mem))
> +               ret = PTR_ERR(pcie_ep->icc_mem);
> +
>         return ret;
>  }
>
> @@ -572,6 +639,7 @@ static irqreturn_t qcom_pcie_ep_global_irq_thread(int irq, void *data)
>         } else if (FIELD_GET(PARF_INT_ALL_BME, status)) {
>                 dev_dbg(dev, "Received BME event. Link is enabled!\n");
>                 pcie_ep->link_status = QCOM_PCIE_EP_LINK_ENABLED;
> +               qcom_pcie_ep_icc_update(pcie_ep);
>         } else if (FIELD_GET(PARF_INT_ALL_PM_TURNOFF, status)) {
>                 dev_dbg(dev, "Received PM Turn-off event! Entering L23\n");
>                 val = readl_relaxed(pcie_ep->parf + PARF_PM_CTRL);
> --
> 2.7.4
>


-- 
With best wishes
Dmitry



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux