Re: [PATCH v6 3/5] dmaengine: dw-edma: Add support for native HDMA

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 13 3月 23 02:11:10, Serge Semin wrote:
> On Fri, Mar 10, 2023 at 11:23:36AM +0800, Cai Huoqing wrote:
> > Add support for HDMA NATIVE, as long the IP design has set
> > the compatible register map parameter-HDMA_NATIVE,
> > which allows compatibility for native HDMA register configuration.
> > 
> > The HDMA Hyper-DMA IP is an enhancement of the eDMA embedded-DMA IP.
> > And the native HDMA registers are different from eDMA, so this patch
> > add support for HDMA NATIVE mode.
> > 
> > HDMA write and read channels operate independently to maximize
> > the performance of the HDMA read and write data transfer over
> > the link When you configure the HDMA with multiple read channels,
> > then it uses a round robin (RR) arbitration scheme to select
> > the next read channel to be serviced.The same applies when you
> > have multiple write channels.
> > 
> > The native HDMA driver also supports a maximum of 16 independent
> > channels (8 write + 8 read), which can run simultaneously.
> > Both SAR (Source Address Register) and DAR (Destination Address Register)
> > are aligned to byte.
> > 
> > Signed-off-by: Cai Huoqing <cai.huoqing@xxxxxxxxx>
> > ---
> > v5->v6:
> >   6.Remove some unnecessary wrapper function.
> >   7.Using one loop instead two in dw_hdma_v0_core_handle_int.
> >   8.Fix the method to returning the actual IRQ-handling status.
> > 
> > v5 link:
> > 	https://lore.kernel.org/lkml/20230303124642.5519-4-cai.huoqing@xxxxxxxxx/
> > 
> >  drivers/dma/dw-edma/Makefile          |   5 +-
> >  drivers/dma/dw-edma/dw-edma-core.c    |   6 +-
> >  drivers/dma/dw-edma/dw-hdma-v0-core.c | 275 ++++++++++++++++++++++++++
> >  drivers/dma/dw-edma/dw-hdma-v0-core.h |  17 ++
> >  drivers/dma/dw-edma/dw-hdma-v0-regs.h | 129 ++++++++++++
> >  include/linux/dma/edma.h              |   3 +-
> >  6 files changed, 431 insertions(+), 4 deletions(-)
> >  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.c
> >  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-core.h
> >  create mode 100644 drivers/dma/dw-edma/dw-hdma-v0-regs.h
> > 
> > diff --git a/drivers/dma/dw-edma/Makefile b/drivers/dma/dw-edma/Makefile
> > index 8d45c0d5689d..b1c91ef2c63d 100644
> > --- a/drivers/dma/dw-edma/Makefile
> > +++ b/drivers/dma/dw-edma/Makefile
> > @@ -2,6 +2,7 @@
> >  
> >  obj-$(CONFIG_DW_EDMA)		+= dw-edma.o
> >  dw-edma-$(CONFIG_DEBUG_FS)	:= dw-edma-v0-debugfs.o
> > -dw-edma-objs			:= dw-edma-core.o \
> > -					dw-edma-v0-core.o $(dw-edma-y)
> > +dw-edma-objs			:= dw-edma-core.o	\
> > +				   dw-edma-v0-core.o	\
> > +				   dw-hdma-v0-core.o $(dw-edma-y)
> >  obj-$(CONFIG_DW_EDMA_PCIE)	+= dw-edma-pcie.o
> > diff --git a/drivers/dma/dw-edma/dw-edma-core.c b/drivers/dma/dw-edma/dw-edma-core.c
> > index dc2908b66493..05c98b803a85 100644
> > --- a/drivers/dma/dw-edma/dw-edma-core.c
> > +++ b/drivers/dma/dw-edma/dw-edma-core.c
> > @@ -18,6 +18,7 @@
> >  
> >  #include "dw-edma-core.h"
> >  #include "dw-edma-v0-core.h"
> > +#include "dw-hdma-v0-core.h"
> >  #include "../dmaengine.h"
> >  #include "../virt-dma.h"
> >  
> > @@ -923,7 +924,10 @@ int dw_edma_probe(struct dw_edma_chip *chip)
> >  
> >  	dw->chip = chip;
> >  
> > -	dw_edma_v0_core_register(dw);
> > +	if (dw->chip->mf == EDMA_MF_HDMA_NATIVE)
> > +		dw_hdma_v0_core_register(dw);
> > +	else
> > +		dw_edma_v0_core_register(dw);
> >  
> >  	raw_spin_lock_init(&dw->lock);
> >  
> > diff --git a/drivers/dma/dw-edma/dw-hdma-v0-core.c b/drivers/dma/dw-edma/dw-hdma-v0-core.c
> > new file mode 100644
> > index 000000000000..5446e9f38d65
> > --- /dev/null
> > +++ b/drivers/dma/dw-edma/dw-hdma-v0-core.c
> > @@ -0,0 +1,275 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (c) 2023 Cai Huoqing
> > + * Synopsys DesignWare HDMA v0 core
> > + */
> > +
> > +#include <linux/bitfield.h>
> > +#include <linux/irqreturn.h>
> > +#include <linux/io-64-nonatomic-lo-hi.h>
> > +
> > +#include "dw-edma-core.h"
> > +#include "dw-hdma-v0-core.h"
> > +#include "dw-hdma-v0-regs.h"
> > +
> > +enum dw_hdma_control {
> > +	DW_HDMA_V0_CB					= BIT(0),
> > +	DW_HDMA_V0_TCB					= BIT(1),
> > +	DW_HDMA_V0_LLP					= BIT(2),
> > +	DW_HDMA_V0_LIE					= BIT(3),
> > +	DW_HDMA_V0_RIE					= BIT(4),
> > +	DW_HDMA_V0_CCS					= BIT(8),
> > +	DW_HDMA_V0_LLE					= BIT(9),
> > +};
> > +
> > +static inline struct dw_hdma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
> > +{
> > +	return dw->chip->reg_base;
> > +}
> > +
> > +static inline struct dw_hdma_v0_ch_regs __iomem *
> > +__dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
> > +{
> > +	if (dir == EDMA_DIR_WRITE)
> > +		return &(__dw_regs(dw)->ch[ch].wr);
> > +	else
> > +		return &(__dw_regs(dw)->ch[ch].rd);
> > +}
> > +
> > +#define SET_CH_32(dw, dir, ch, name, value) \
> > +	writel(value, &(__dw_ch_regs(dw, dir, ch)->name))
> > +
> > +#define GET_CH_32(dw, dir, ch, name) \
> > +	readl(&(__dw_ch_regs(dw, dir, ch)->name))
> > +
> > +#define SET_BOTH_CH_32(dw, ch, name, value) \
> > +	do {					\
> > +		writel(value, &(__dw_ch_regs(dw, EDMA_DIR_WRITE, ch)->name));	\
> > +		writel(value, &(__dw_ch_regs(dw, EDMA_DIR_READ, ch)->name));	\
> > +	} while (0)
> > +
> > +/* HDMA management callbacks */
> > +static void dw_hdma_v0_core_off(struct dw_edma *dw)
> > +{
> > +	int id;
> > +
> > +	for (id = 0; id < HDMA_V0_MAX_NR_CH; id++) {
> > +		SET_BOTH_CH_32(dw, id, int_setup,
> > +			       HDMA_V0_STOP_INT_MASK | HDMA_V0_ABORT_INT_MASK);
> > +		SET_BOTH_CH_32(dw, id, int_clear,
> > +			       HDMA_V0_STOP_INT_MASK | HDMA_V0_ABORT_INT_MASK);
> > +		SET_BOTH_CH_32(dw, id, ch_en, 0);
> > +	}
> > +}
> > +
> > +static u16 dw_hdma_v0_core_ch_count(struct dw_edma *dw, enum dw_edma_dir dir)
> > +{
> > +	u32 num_ch = 0;
> > +	int id;
> > +
> > +	for (id = 0; id < HDMA_V0_MAX_NR_CH; id++) {
> > +		if (GET_CH_32(dw, id, dir, ch_en) & BIT(0))
> > +			num_ch++;
> > +	}
> > +
> > +	if (num_ch > HDMA_V0_MAX_NR_CH)
> > +		num_ch = HDMA_V0_MAX_NR_CH;
> > +
> > +	return (u16)num_ch;
> > +}
> > +
> > +static enum dma_status dw_hdma_v0_core_ch_status(struct dw_edma_chan *chan)
> > +{
> > +	struct dw_edma *dw = chan->dw;
> > +	u32 tmp;
> > +
> > +	tmp = FIELD_GET(HDMA_V0_CH_STATUS_MASK,
> > +			GET_CH_32(dw, chan->id, chan->dir, ch_stat));
> > +
> > +	if (tmp == 1)
> > +		return DMA_IN_PROGRESS;
> > +	else if (tmp == 3)
> > +		return DMA_COMPLETE;
> > +	else
> > +		return DMA_ERROR;
> > +}
> > +
> 
> > +static
> > +irqreturn_t dw_hdma_v0_core_handle_int(struct dw_edma_irq *dw_irq, enum dw_edma_dir dir,
> > +				       dw_edma_handler_t done, dw_edma_handler_t abort)
> 
> Please place the return value together with the modifier too:
> +static irqreturn_t
> +dw_hdma_v0_core_handle_int(struct dw_edma_irq *dw_irq, enum dw_edma_dir dir,
> +			    dw_edma_handler_t done, dw_edma_handler_t abort)
> 
> as it's normally done in the driver for the non-inline methods.
> 
> > +{
> > +	struct dw_edma *dw = dw_irq->dw;
> > +	unsigned long total, pos, val;
> > +	irqreturn_t ret = IRQ_NONE;
> > +	struct dw_edma_chan *chan;
> > +	unsigned long off, mask;
> > +
> > +	if (dir == EDMA_DIR_WRITE) {
> > +		total = dw->wr_ch_cnt;
> > +		off = 0;
> > +		mask = dw_irq->wr_mask;
> > +	} else {
> > +		total = dw->rd_ch_cnt;
> > +		off = dw->wr_ch_cnt;
> > +		mask = dw_irq->rd_mask;
> > +	}
> > +
> > +	for_each_set_bit(pos, &mask, total) {
> > +		chan = &dw->chan[pos + off];
> > +
> 
> > +		val = GET_CH_32(dw, chan->dir, chan->id, int_stat);
> > +		if (FIELD_GET(HDMA_V0_STOP_INT_MASK, val)) {
> > +			SET_CH_32(dw, chan->dir, chan->id,
> > +				  int_clear, HDMA_V0_STOP_INT_MASK);
> > +			done(chan);
> > +
> > +			ret = IRQ_HANDLED;
> > +		}
> > +
> > +		if (FIELD_GET(HDMA_V0_ABORT_INT_MASK, val)) {
> > +			SET_CH_32(dw, chan->dir, chan->id,
> > +				  int_clear, HDMA_V0_ABORT_INT_MASK);
> 
> In v5 I was talking about the dw_hdma_v0_core_check_done_int() and
> dw_hdma_v0_core_check_abort_int() methods only. They didn't imply any
> CSR access but merely returned a field of the passed value. So
> creating a separate function just for that seemed redundant. The rest
I know, but I think remove these methods make code simple, and
it's unnecessary to keep them just for read or write a register.

What do you think?

Thanks
-Cai
> of the inliners (dw_hdma_v0_core_clear_done_int(),
> dw_hdma_v0_core_clear_abort_int() and dw_hdma_v0_core_status_int())
> looked ok to me.
> 
> > +			abort(&dw->chan[pos + off]);
> 
> em, why not "abort(chan);" here?
> 
> -Serge(y)
> 
> > +
> > +			ret = IRQ_HANDLED;
> > +		}
> > +	}
> > +
> > +	return ret;
> > +}
> > +
> > +static void dw_hdma_v0_write_ll_data(struct dw_edma_chunk *chunk, int i,
> > +				     u32 control, u32 size, u64 sar, u64 dar)
> > +{
> > +	ptrdiff_t ofs = i * sizeof(struct dw_hdma_v0_lli);
> > +
> > +	if (chunk->chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL) {
> > +		struct dw_hdma_v0_lli *lli = chunk->ll_region.vaddr.mem + ofs;
> > +
> > +		lli->control = control;
> > +		lli->transfer_size = size;
> > +		lli->sar.reg = sar;
> > +		lli->dar.reg = dar;
> > +	} else {
> > +		struct dw_hdma_v0_lli __iomem *lli = chunk->ll_region.vaddr.io + ofs;
> > +
> > +		writel(control, &lli->control);
> > +		writel(size, &lli->transfer_size);
> > +		writeq(sar, &lli->sar.reg);
> > +		writeq(dar, &lli->dar.reg);
> > +	}
> > +}
> > +
> > +static void dw_hdma_v0_write_ll_link(struct dw_edma_chunk *chunk,
> > +				     int i, u32 control, u64 pointer)
> > +{
> > +	ptrdiff_t ofs = i * sizeof(struct dw_hdma_v0_lli);
> > +
> > +	if (chunk->chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL) {
> > +		struct dw_hdma_v0_llp *llp = chunk->ll_region.vaddr.mem + ofs;
> > +
> > +		llp->control = control;
> > +		llp->llp.reg = pointer;
> > +	} else {
> > +		struct dw_hdma_v0_llp __iomem *llp = chunk->ll_region.vaddr.io + ofs;
> > +
> > +		writel(control, &llp->control);
> > +		writeq(pointer, &llp->llp.reg);
> > +	}
> > +}
> > +
> > +static void dw_hdma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
> > +{
> > +	struct dw_edma_burst *child;
> > +	struct dw_edma_chan *chan = chunk->chan;
> > +	u32 control = 0, i = 0;
> > +	int j;
> > +
> > +	if (chunk->cb)
> > +		control = DW_HDMA_V0_CB;
> > +
> > +	j = chunk->bursts_alloc;
> > +	list_for_each_entry(child, &chunk->burst->list, list) {
> > +		j--;
> > +		if (!j) {
> > +			control |= DW_HDMA_V0_LIE;
> > +			if (!(chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL))
> > +				control |= DW_HDMA_V0_RIE;
> > +		}
> > +
> > +		dw_hdma_v0_write_ll_data(chunk, i++, control, child->sz,
> > +					 child->sar, child->dar);
> > +	}
> > +
> > +	control = DW_HDMA_V0_LLP | DW_HDMA_V0_TCB;
> > +	if (!chunk->cb)
> > +		control |= DW_HDMA_V0_CB;
> > +
> > +	dw_hdma_v0_write_ll_link(chunk, i, control, chunk->ll_region.paddr);
> > +}
> > +
> > +static void dw_hdma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
> > +{
> > +	struct dw_edma_chan *chan = chunk->chan;
> > +	struct dw_edma *dw = chan->dw;
> > +	u32 tmp;
> > +
> > +	dw_hdma_v0_core_write_chunk(chunk);
> > +
> > +	if (first) {
> > +		/* Enable engine */
> > +		SET_CH_32(dw, chan->dir, chan->id, ch_en, BIT(0));
> > +		/* Interrupt enable&unmask - done, abort */
> > +		tmp = GET_CH_32(dw, chan->dir, chan->id, int_setup) |
> > +		      HDMA_V0_STOP_INT_MASK | HDMA_V0_ABORT_INT_MASK |
> > +		      HDMA_V0_LOCAL_STOP_INT_EN | HDMA_V0_LOCAL_STOP_INT_EN;
> > +		SET_CH_32(dw, chan->dir, chan->id, int_setup, tmp);
> > +		/* Channel control */
> > +		SET_CH_32(dw, chan->dir, chan->id, control1, HDMA_V0_LINKLIST_EN);
> > +		/* Linked list */
> > +		/* llp is not aligned on 64bit -> keep 32bit accesses */
> > +		SET_CH_32(dw, chan->dir, chan->id, llp.lsb,
> > +			  lower_32_bits(chunk->ll_region.paddr));
> > +		SET_CH_32(dw, chan->dir, chan->id, llp.msb,
> > +			  upper_32_bits(chunk->ll_region.paddr));
> > +	}
> > +	/* Set consumer cycle */
> > +	SET_CH_32(dw, chan->dir, chan->id, cycle_sync,
> > +		  HDMA_V0_CONSUMER_CYCLE_STAT | HDMA_V0_CONSUMER_CYCLE_BIT);
> > +	/* Doorbell */
> > +	SET_CH_32(dw, chan->dir, chan->id, doorbell, HDMA_V0_DOORBELL_START);
> > +}
> > +
> > +static void dw_hdma_v0_core_ch_config(struct dw_edma_chan *chan)
> > +{
> > +	struct dw_edma *dw = chan->dw;
> > +
> > +	/* MSI done addr - low, high */
> > +	SET_CH_32(dw, chan->dir, chan->id, msi_stop.lsb, chan->msi.address_lo);
> > +	SET_CH_32(dw, chan->dir, chan->id, msi_stop.msb, chan->msi.address_hi);
> > +	/* MSI abort addr - low, high */
> > +	SET_CH_32(dw, chan->dir, chan->id, msi_abort.lsb, chan->msi.address_lo);
> > +	SET_CH_32(dw, chan->dir, chan->id, msi_abort.msb, chan->msi.address_hi);
> > +	/* config MSI data */
> > +	SET_CH_32(dw, chan->dir, chan->id, msi_msgdata, chan->msi.data);
> > +}
> > +
> > +/* HDMA debugfs callbacks */
> > +static void dw_hdma_v0_core_debugfs_on(struct dw_edma *dw)
> > +{
> > +}
> > +
> > +static const struct dw_edma_core_ops dw_hdma_v0_core = {
> > +	.off = dw_hdma_v0_core_off,
> > +	.ch_count = dw_hdma_v0_core_ch_count,
> > +	.ch_status = dw_hdma_v0_core_ch_status,
> > +	.handle_int = dw_hdma_v0_core_handle_int,
> > +	.start = dw_hdma_v0_core_start,
> > +	.ch_config = dw_hdma_v0_core_ch_config,
> > +	.debugfs_on = dw_hdma_v0_core_debugfs_on,
> > +};
> > +
> > +void dw_hdma_v0_core_register(struct dw_edma *dw)
> > +{
> > +	dw->core = &dw_hdma_v0_core;
> > +}
> > diff --git a/drivers/dma/dw-edma/dw-hdma-v0-core.h b/drivers/dma/dw-edma/dw-hdma-v0-core.h
> > new file mode 100644
> > index 000000000000..c373b4f0bd8a
> > --- /dev/null
> > +++ b/drivers/dma/dw-edma/dw-hdma-v0-core.h
> > @@ -0,0 +1,17 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (c) 2023 Cai Huoqing
> > + * Synopsys DesignWare HDMA v0 core
> > + *
> > + * Author: Cai Huoqing <cai.huoqing@xxxxxxxxx>
> > + */
> > +
> > +#ifndef _DW_HDMA_V0_CORE_H
> > +#define _DW_HDMA_V0_CORE_H
> > +
> > +#include <linux/dma/edma.h>
> > +
> > +/* HDMA core register */
> > +void dw_hdma_v0_core_register(struct dw_edma *dw);
> > +
> > +#endif /* _DW_HDMA_V0_CORE_H */
> > diff --git a/drivers/dma/dw-edma/dw-hdma-v0-regs.h b/drivers/dma/dw-edma/dw-hdma-v0-regs.h
> > new file mode 100644
> > index 000000000000..1106f56280c0
> > --- /dev/null
> > +++ b/drivers/dma/dw-edma/dw-hdma-v0-regs.h
> > @@ -0,0 +1,129 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/*
> > + * Copyright (c) 2023 Cai Huoqing
> > + * Synopsys DesignWare HDMA v0 reg
> > + *
> > + * Author: Cai Huoqing <cai.huoqing@xxxxxxxxx>
> > + */
> > +
> > +#ifndef _DW_HDMA_V0_REGS_H
> > +#define _DW_HDMA_V0_REGS_H
> > +
> > +#include <linux/dmaengine.h>
> > +
> > +#define HDMA_V0_MAX_NR_CH			8
> > +#define HDMA_V0_LOCAL_ABORT_INT_EN		BIT(6)
> > +#define HDMA_V0_REMOTE_ABORT_INT_EN		BIT(5)
> > +#define HDMA_V0_LOCAL_STOP_INT_EN		BIT(4)
> > +#define HDMA_V0_REMOTEL_STOP_INT_EN		BIT(3)
> > +#define HDMA_V0_ABORT_INT_MASK			BIT(2)
> > +#define HDMA_V0_STOP_INT_MASK			BIT(0)
> > +#define HDMA_V0_LINKLIST_EN			BIT(0)
> > +#define HDMA_V0_CONSUMER_CYCLE_STAT		BIT(1)
> > +#define HDMA_V0_CONSUMER_CYCLE_BIT		BIT(0)
> > +#define HDMA_V0_DOORBELL_START			BIT(0)
> > +#define HDMA_V0_CH_STATUS_MASK			GENMASK(1, 0)
> > +
> > +struct dw_hdma_v0_ch_regs {
> > +	u32 ch_en;				/* 0x0000 */
> > +	u32 doorbell;				/* 0x0004 */
> > +	u32 prefetch;				/* 0x0008 */
> > +	u32 handshake;				/* 0x000c */
> > +	union {
> > +		u64 reg;			/* 0x0010..0x0014 */
> > +		struct {
> > +			u32 lsb;		/* 0x0010 */
> > +			u32 msb;		/* 0x0014 */
> > +		};
> > +	} llp;
> > +	u32 cycle_sync;				/* 0x0018 */
> > +	u32 transfer_size;			/* 0x001c */
> > +	union {
> > +		u64 reg;			/* 0x0020..0x0024 */
> > +		struct {
> > +			u32 lsb;		/* 0x0020 */
> > +			u32 msb;		/* 0x0024 */
> > +		};
> > +	} sar;
> > +	union {
> > +		u64 reg;			/* 0x0028..0x002c */
> > +		struct {
> > +			u32 lsb;		/* 0x0028 */
> > +			u32 msb;		/* 0x002c */
> > +		};
> > +	} dar;
> > +
> > +	u32 watermark_en;			/* 0x0030 */
> > +	u32 control1;				/* 0x0034 */
> > +	u32 func_num;				/* 0x0038 */
> > +	u32 qos;				/* 0x003c */
> > +	u64 reserved[8];			/* 0x0040..0x0078 */
> > +	u32 ch_stat;				/* 0x0080 */
> > +	u32 int_stat;				/* 0x0084 */
> > +	u32 int_setup;				/* 0x0088 */
> > +	u32 int_clear;				/* 0x008c */
> > +	union {
> > +		u64 reg;			/* 0x0090..0x0094 */
> > +		struct {
> > +			u32 lsb;		/* 0x0090 */
> > +			u32 msb;		/* 0x0094 */
> > +		};
> > +	} msi_stop;
> > +	union {
> > +		u64 reg;			/* 0x0098..0x009c */
> > +		struct {
> > +			u32 lsb;		/* 0x0098 */
> > +			u32 msb;		/* 0x009c */
> > +		};
> > +	} msi_watermark;
> > +	union {
> > +		u64 reg;			/* 0x00a0..0x00a4 */
> > +		struct {
> > +			u32 lsb;		/* 0x00a0 */
> > +			u32 msb;		/* 0x00a4 */
> > +		};
> > +	} msi_abort;
> > +	u32 msi_msgdata;			/* 0x00a8 */
> > +} __packed;
> > +
> > +struct dw_hdma_v0_ch {
> > +	struct dw_hdma_v0_ch_regs wr;		/* 0x0000 */
> > +	struct dw_hdma_v0_ch_regs rd;		/* 0x0100 */
> > +} __packed;
> > +
> > +struct dw_hdma_v0_regs {
> > +	struct dw_hdma_v0_ch ch[HDMA_V0_MAX_NR_CH];	/* 0x0000..0x0fa8 */
> > +} __packed;
> > +
> > +struct dw_hdma_v0_lli {
> > +	u32 control;
> > +	u32 transfer_size;
> > +	union {
> > +		u64 reg;
> > +		struct {
> > +			u32 lsb;
> > +			u32 msb;
> > +		};
> > +	} sar;
> > +	union {
> > +		u64 reg;
> > +		struct {
> > +			u32 lsb;
> > +			u32 msb;
> > +		};
> > +	} dar;
> > +} __packed;
> > +
> > +struct dw_hdma_v0_llp {
> > +	u32 control;
> > +	u32 reserved;
> > +	union {
> > +		u64 reg;
> > +		struct {
> > +			u32 lsb;
> > +			u32 msb;
> > +		};
> > +	} llp;
> > +} __packed;
> > +
> > +#endif /* _DW_HDMA_V0_REGS_H */
> > diff --git a/include/linux/dma/edma.h b/include/linux/dma/edma.h
> > index ed401c965a87..3080747689f6 100644
> > --- a/include/linux/dma/edma.h
> > +++ b/include/linux/dma/edma.h
> > @@ -48,7 +48,8 @@ struct dw_edma_plat_ops {
> >  enum dw_edma_map_format {
> >  	EDMA_MF_EDMA_LEGACY = 0x0,
> >  	EDMA_MF_EDMA_UNROLL = 0x1,
> > -	EDMA_MF_HDMA_COMPAT = 0x5
> > +	EDMA_MF_HDMA_COMPAT = 0x5,
> > +	EDMA_MF_HDMA_NATIVE = 0x7,
> >  };
> >  
> >  /**
> > -- 
> > 2.34.1
> > 



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux