Le 2023-03-04 00:42, Frank Rowand a écrit : > On 2/27/23 04:31, Clément Léger wrote: >> Le Mon, 27 Feb 2023 00:51:29 -0600, >> Frank Rowand <frowand.list@xxxxxxxxx> a écrit : >> >>> On 1/19/23 21:02, Lizhi Hou wrote: >>>> This patch series introduces OF overlay support for PCI devices >>>> which >>>> primarily addresses two use cases. First, it provides a data driven >>>> method >>>> to describe hardware peripherals that are present in a PCI endpoint >>>> and >>>> hence can be accessed by the PCI host. Second, it allows reuse of a >>>> OF >>>> compatible driver -- often used in SoC platforms -- in a PCI host >>>> based >>>> system. >>>> >>>> There are 2 series devices rely on this patch: >>>> >>>> 1) Xilinx Alveo Accelerator cards (FPGA based device) >>>> 2) Microchip LAN9662 Ethernet Controller >>>> >>>> Please see: >>>> https://lore.kernel.org/lkml/20220427094502.456111-1-clement.leger@xxxxxxxxxxx/ >>>> >>> >>> >>>> Normally, the PCI core discovers PCI devices and their BARs using >>>> the >>>> PCI enumeration process. However, the process does not provide a way >>>> to >>>> discover the hardware peripherals that are present in a PCI device, >>>> and >>>> which can be accessed through the PCI BARs. Also, the enumeration >>>> process >>> >>> I'm confused. The PCI Configuration Header Registers should describe >>> the >>> hardware on the PCI card. >>> >>> Ignoring case 1 above _for the moment_ (FPGA devices are a world unto >>> themselves, so I would like to analyze that case separately), does >>> the >>> second device, "Microchip LAN9662 Ethernet Controller" properly >>> implement >>> the PCI Configuration Header Registers? What additional information >>> is >>> needed that is not provided in those registers? >> >> Hi Frank, >> >> I guess Lizhi wanted to say that it does not provide a way to describe >> all the "platform" devices that are exposed by this PCI device. Which >> is of course the whole point of the work we are doing right now. But >> all the BARs are correctly described by the LAN9662 PCI card. >> >> Clément > > I remain confused. > > [RFC 00/10] add support for fwnode in i2c mux system and sfp > https://lore.kernel.org/lkml/YhQHqDJvahgriDZK@xxxxxxx/t/ > > references a PCIe driver: > [2] > https://github.com/clementleger/linux/blob/fwnode_support/drivers/mfd/lan966x_pci_mfd.c > > So there is a PCIe driver that works. > > However, the RFC patch series was proposing adding fwnode support to > the driver. My first > surface reading (just part of that one email, not the entire series or > the replies yet), > notes: > > ... However, when > plugged in a PCIe slot (on a x86), there is no device-tree support > and > the peripherals that are present must be described in some other way. > > I am assuming that the peripherals are what you mentioned above as > '"platform" > devices'. This is where my current confusion lies. Are the "platform" > devices accessed via the PCI bus or is there some other electrical > connection > between the host system and the PCIe card? Hi Frank, The platform devices exposed by this PCIe card are available via some BAR using PCI memory mapped areas, so it's totally standard PCI stuff. > > If the "platform" devices are accessed via the PCI bus, then I would > expect them > to be described by PCI configuration header registers. Are the PCI > configuration > registers to describe the "platform" devices not present? I'm not sure to understand what you mean here. PCI configuration headers only provides some basic registers allowing to identify the PCI device (vendor/product) and some memory areas that are exposed (BAR). They do not provides the "list" of peripherals that are exposed by the devices, only some BARs that can be mapped and that allows to access. In the case of the lan9662 cnetwork controller, BAR 0 and 1 exposes multiples devices that are located at some subranges of this BAR. For instance (not accurate), we have the I2C controller located at BAR 0 + offset 0X1000, then the flexcom controller exposed in BAR 0 at offset 0x20000, etc. This list of peripheral is not exposed at all by the PCI configuration headers (since it is not the purpose of course). All of these peripherals have already existing platform drivers which can then be reused thanks to the PCI device-tree overlay series. > > I'll read through the fwnode RFC thread to add to see what happened to > the proposal. You can probably read the cover letter which described the use case in details. However, don't spend too much time reading the patchset, we discarded them for many good reason (way too much modifications in subsystems, no standardization of software node bindings, etc). Clément
